Caro VISION II Operating Instructions Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Table of Contents

Troubleshooting

Summary of Contents for Caro VISION II

Page 2: Operating Instructions
Operating Instructions CARO VISION II Date: August 2006 Software Version 1.07...
Page 3: Proper Use And Operation
Proper use and operation This product has been designed for use in a fixed installation on mobile homes or trailers with a maximum speed of no more than 130 km/h. It is designed to automatically aim a parabolic antenna mounted on a stationary vehicle at geostationary television satellites transmitting directly to Europe.
Page 4: Table Of Contents
Table of contents Proper use and operation Table of contents Introduction The first steps Switching ON / switching OFF General menu Automatic satellite search Manual satellite search Satellite swap Menu "Settings" DISEqC system Restarting the system Troubleshooting table DISEqC troubleshooting table Safety instructions Appendix - Search satellites Reception in remote areas...
Page 5: Introduction
TV signal will be received. The first few pages of these instructions contain information about using the general functions of your CARO, followed by an explanation of all the adjustment options. The last pages of the instructions cover...
Page 6: The First Steps
We have produced a separate manual – the “Installation Instructions” – which covers the installation, wiring and initial taking into operation of your CARO. All of the steps from unpacking and installing the system to switching it on for the first time are explained there, together with various default settings that need to be performed.
Page 7 To ensure safe and reliable operation of the system, please make sure the CARO is in rest mode before disconnecting the control panel. Check that no text is displayed on the panel – this is an indication that it is in...
Page 8: Switching On / Switching Off
Switching ON / switching OFF Your CARO system is very straightforward to use. Simply press the button and your CARO will immediately start to work. Please remember to switch on your satellite receiver and your TV set or flat-screen display. The CARO system functions independently of your TV set or receiver, but if these devices are switched off, no TV or radio channel can be received.
Page 9: General Menu
General menu Whenever your CARO system is active and not performing any special functions such as retracting or opening or automatically searching or changing to a different satellite, you have direct access to the general menu from which you can start all functions or select submenus.
Page 10: Automatic Satellite Search
Automatic satellite search After switching on the system by pressing , the antenna opens and moves into the position in which a satellite was last received. If not satellite is found, the system starts the fully automated search for the preset satellite (default setting: Astra 1).
Page 11: Manual Satellite Search
Manual satellite search The manual search is usually used to fine-tune the antenna to a found satellite under adverse reception conditions. If you wish to receive signals from a new satellite that is not yet stored as a search satellite in the control unit, the manual search function can be used to tune the system to this satellite.
Page 12: Satellite Swap
Satellite swap Generally, satellites can be swapped by entering a different satellite in the menu option "Search satellite" and selecting the automatic search. To facilitate a quick and convenient swap to a different satellite, the so- called "quick satellite-swap" function has been added to the DISEqC system.
Page 13 automatic search has been started and the vehicle has not moved since, aiming will be much quicker. However, after retracting and re-opening the system, the antenna will be moved into the position of the preset "search satellite" (see page 14).
Page 14: Menu "Settings
In the general menu, scroll to item Settings and press to activate it. The menu cannot be accessed when the system is switched off. Therefore you need to switch the CARO system on before you can use the menu. Menu controls...
Page 15: Menu Structure
Menu structure Automatic Manual search Swap satellite search Sat mode Settings return Language (to Settings) Mechanical Search adjustment satellite Min. elevation Service Info Diseqc/Sat- Pos. DiseqC: return monitor (to Diseqc/Sat-Pos) DiseqC: Sat position 4 On/Off Sat position 3 Sat position 2 Sat position 1...
Page 16 Language Selection of the language for the texts displayed on the control panel. Search satellite Select "Astra 1", "Hotbird" or any other satellite (see Search satellite on page 26). Select the satellite transmitting your preferred channel which is receivable at your current location. To receive English-language channels in Europe, "Astra II"...
Page 17 (LNB) will move over the roof during the satellite search. If any vehicle parts are within the pivoting space, collisions may occur which may result in a damage of your CARO or the respective vehicle part. Often, the satellite system needs to be installed in restricted spaces. The minimum elevation setting will then prevent the LNB from moving into positions below the set value.
Page 18 Only activate the DISEqC function if you wish to frequently change between individual satellites and if your receiver is DISEqC-compatible. Even when activated, the DISEqC function (DISEqC: ON) is only operational when your CARO system is in "rest mode". This is indicated by the messages (Main menu) or (sat-mode) in the control panel.
Page 19 Please note: Your CARO system as well as your receiver must be correctly programmed and matched to each other to ensure that the DISEqC features work. Please refer to the manual of your receiver for further information on programming the receiver.
Page 20: Diseqc System
(DVB-S receivers). The CARO system uses this DISEqC signal to automatically move the antenna into up to four preset satellite positions. The initial configuration of a DISEqC system is relatively complex and can be a challenge even to the experienced user.
Page 21 If this is not the case, you will need to store the channels first. To do this, search for the relevant satellite with your CARO by selecting the relevant search satellite (see page 14) and using the automatic search.
Page 22 02 should be displayed, as this satellite has been assigned to position B (2). If the position display functions correctly, the satellite position is assigned to the corresponding satellite in the CARO control panel. To do this, select the menu option "SAT position" (see page 17).
Page 23 Please note that the DISEqC signals can only be processed when your CARO is in "rest mode". This is indicated by the message (Main menu) or (Sat-mode) in the display.
Page 24: Restarting The System
If you think that your CARO system is responding incorrectly or it is not responding at all, then we recommend restarting the microprocessor. There are different ways to do this: - If the fuse in the wiring harness is easily accessible, remove the fuse and then re-insert it into its holder after a few seconds.
Page 25: Troubleshooting Table
Troubleshooting table Malfunctions of the automatic antenna unit may occur e. g. when the antenna's motion is obstructed by branches or snow. Such malfunctions are automatically detected and will be indicated in the display of the control unit. Malfunction Remedial action The search did not yield Do you have a clear view to the reception...
Page 26: Diseqc Troubleshooting Table
Activate the simplest DISEqC function. (Refer to the manual of your satellite receiver.) DISEqC function activated at the CARO system? (DISEqC: On) In the menu option "DISEqC monitor", the values are shown Does the control panel display correctly, but the system does show "Main menu"...
Page 27 "SAT position" correctly correctly, and the antenna moves set? The assignment in the when changing the channel, but CARO system must be the same the TV screen remains blank. as in the receiver. 3) Are you located in an area in...
Page 28: Safety Instructions
Safety instructions In order to ensure that your CARO system works properly, you must ensure that it is correctly connected to the ignition of your vehicle (see Installation Instructions). When it is correctly installed, the antenna automatically assumes the rest position when the ignition is switched on and locks itself there.
Page 29: Appendix - Search Satellites
Appendix - Search satellites These satellites are pre-set in your CARO system for direct searching. To select, navigate to Main menu SAT settings Search satellite (see page 14). ASTRA 1 Astra 1 primarily serves the German-speaking regions of Europe. It transmits all German-language television channels, private and public channels and all regional public TV and radio channels.
Page 30 ATLANTIC BIRD 3 Atlantic Bird 3 mainly covers France and Benelux, but can also be received all over Europe, depending on the transponder. It transmits several digital free- to-air French channels. ATLANTIC BIRD 2 Atlantic Bird 2 is mainly used for internet services, but also transmits some TV channels.
Page 31: Reception In Remote Areas
Reception in remote areas State-of-the art digital technology can considerably enlarge the area in which a satellite can be received. Most satellites broadcasting channels of interest to Central European viewers are aimed at Central Europe. In locations outside this area, the antenna has a lateral "view"...
Page 32: Notes On Protection Of The Environment
Notes on protection of the environment At the end of its lifecycle, this product must not be disposed of with your normal waste, but instead must be returned to a recycling facility for electric and electronic devices. This is indicated by the symbol on the product, the operating manual or the packaging.
Page 33: Contact And Service
Phone: +49 (0)72 37 / 48 55 – 0 We are available Monday – Friday 7.30 a.m. – 5.30 p.m. We hope you get a lot of enjoyment out of your CARO VISION II system. ten Haaft GmbH www.ten-haaft.de E-mail:...