Using Your Quartet; Additional Handset - BT Quartet 1000 User Manual

Quartet 1000 – Edition 3 – 5/9/00 approved
In Use/Battery Aerial
Low light Can be extended.
Indicates when the
handset rings, is in
use or, if the hand-
set is on standby, to
indicate the battery
needs recharging.
M1/M2 buttons Volume control
Allows you to store
buttons
and dial one touch Adjusts the handset
numbers. ringer and earpiece
speech volume.
M1 M2
Talk button
Press to make or
Channel button
receive a call. Selects an alterna-
tive radio frequency
1 2 3
Quickdial button if
Allows you to store interference occurs
4 5 6
and dial up to 10 during a call.
numbers in the
7 8 9
memory. Keypad
0
Redial button Recall button
Redials the last For use with a
Redial R
number called, or switchboard/PBX
press to enter a and BT Select
1471
Secrecy
pause in a stored Services.
number.
1471 button
Secrecy Lets you hear the
Press to mute the telephone number
call so your caller Charging contacts of the last person
cannot hear you. who called.
If you experience any problems then please call
the Quartet Helpline on 0845 769 7146
Setting up
Follow these steps to get your Quartet 1000 addi-
tional handset ready for use.
Like all cordless phones, your Quartet 1000
additional handset will need charging for 24
hours before use.
1 Plug the power cable into the charging unit
Plug the power cable into the socket located on
the bottom of the charging unit, then feed the
cable through the channel.
1
Quartet 1000 – Edition 3 – 5/9/00 approved
2 Connect the power supply unit into a
convenient mains socket
3 Place the handset on the charging unit
Make sure the red CHARGING light at the front
of the charging unit comes on.
4 Leave the handset to charge for 24 hours
When fully charged and in good condition, the
handset will provide up to 7 hours talktime or
72 hours standby.
If the handset battery is running low, the IN
USE/BATTERY LOW light will flash every
10–15 seconds.
If you are making a call and the handset
battery is running low you will hear a warning
tone every 10–15 seconds.
Registering your handset
You must register your Quartet additional hand-
set before it can be used with your Quartet base
unit. Make sure that each additional handset is
registered with a different number (2, 3 or 4) so
it can be identified from other additional hand-
sets, see page 3.
The Quartet 1500 does not feature a PAGE
button. When registering an additional handset
to a base unit please use the base unit
INTERCOM button.
To register an additional handset
Page
• Place the handset you wish to register on the
base unit and then remove it.
• Press and hold the base unit PAGE button for
5 seconds until both the POWER/IN USE light
on the base unit and the IN USE/BATTERY
LOW light on the handset begin to flash.
• Release the PAGE button and press the TALK
button on the handset.
• Your additional handset is registered
automatically and you will hear a long
confirmation beep and the IN USE light will
stop flashing.
2
Quartet 1000 – Edition 3 – 5/9/00 approved
To re-register an additional handset
Before re-registering, the old registration code
must first be erased. If necessary you can
re-register your Quartet 1000 handset by simply
following the above procedures.
To erase a registration code
• Press the QUICKDIAL button
• Press the CHANNEL button.
• Press the button 4 times.
• Press the QUICKDIAL button. You will hear a
confirmation tone.
Your old registration code is now erased and
you can re-register your Quartet 1000 handset
following the procedure above.
Check that your Quartet 1000 handset is
registered correctly by pressing the TALK button
and listening for a dial tone. If you do not hear
a dial tone your Quartet 1000 handset is either
out of range of the base unit or it has not been
registered properly, or the base unit line cord is
not plugged in.
To set the handset number
Each additional handset must be assigned an
identity number (2, 3 or 4). Your Quartet 1100 or
1500 handset is already registered as HANDSET 1.
A Quartet additional handset is pre-set as HAND-
SET 2. However, further additional handsets can
be numbered as they are added.
Secrecy
• Press the QUICKDIAL button.
• Press the SECRECY button.
• Enter the handset number between (2 and 4).
• Press the QUICKDIAL button. You will hear a
beep confirming that the new number has been
stored.
Make a note of the handset number by writing
it on the quickdial label on the additional
handset's charger.
3
Quartet 1000 – Edition 3 – 5/9/00 approved

Using your Quartet

1000 Additional
Handset
Your Quartet 1000 can be used with the Quartet
1100 and Quartet 1500. Please refer to your main
Quartet User Guide for a complete list of product
features and operating instructions.
To make an external call
Press the buttons in the order shown:
• Lift the handset off the base unit.
• Press the TALK button. The POWER/IN USE
light on the base unit begins to flash and the
IN USE light on the handset comes on.
• Listen for the dialling tone.
• Dial the number you want.
To end a call
• Press the TALK button.
Or
• Replace the handset on the base unit.
The handset range is up to 250 metres from the
base unit in ideal conditions. If you start to go
out of range while using the phone, you will
hear warning beeps. Move closer to the base
unit. If you do not move back into range your
call may be disconnected.
Your Quartet 1000 additional handset uses a
compact aerial which can be pulled out to
obtain the best signal and reception available.
Page button – Quartet 1100
The Quartet 1100 base unit features a PAGE but-
ton. When pressed, the base unit and all the
handsets registered to that base unit will ring
and the IN USE/BATTERY LOW light on the
handset will flash. The PAGE button feature does
not enable conversation between the base unit
and handset.
4