Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Soundbarrier PC8MA
- Page 1 PC8MA / PC10MA OWNER’S MANUAL www.soundbarrier.com...
- Page 2 Convenient storage The PC8MA/PC10MA can be used in even the most cramped quarters, inside or outside, since the mixer is built into one of the speaker cabinets. The other speaker has a special compartment for storing speaker cables and microphones, letting you put all you need for your performance in one convenient place.
- Page 3 CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following: Power supply/Power cord Connections Remove the electric plug from the outlet when the devices is not to Before connecting the device to other devices, turn off the power for...
-
Page 4: Specifications
Specifications PC8MA PC10MA ENCLOSURE ENCLOSURE Nominal impedance: 4 ohm Nominal impedance: 4 ohm Frequency response: 70—20K Hz Frequency response: 60—20K Hz Sensitivity (1M/1W): 95 db Sensitivity (1M/1W): 96 db Rated power (RMS): 150W Rated power (RMS): 250W l\LF1*8” woofer will 2” voice coil l\LF1*10”... -
Page 5: Package Contents
Package Contents Two speakers, mixer, panel, power cord, two speaker cables, Owner’s Manual (this booklet) NOTE: The mixer and the panel are installed in the speakers when the PC8MA/PC10MA leaves the factory. Before turning on the mixer Before turning on the mixer Remove the mixer Be sure that the mixer’s power switch is turned off. -
Page 6: Troubleshooting
Troubleshooting Power does not turn on Is the included power cord correctly connected to a power outlet? Amplifier shuts down suddenly Is the vent on the top panel of the mixer blocked? Since inadequate ventilation can result in overheating the mixer, the amplifier may be turned off automatically and the mix may reset itself. - Page 7 When using a condenser microphone, set the PHANTOM switch to ON. Turning the power on First, turn on the power to any connected devices, then turn the PC8MA/PC10MA power on. If you’ve connected powered speakers to the mixer, turn on the power of the mixer first, then the powered speakers.
-
Page 8: Controls And Functions
Use the MASTER LEVEL control to adjust the overall volume. If the LIMITER indicator flashes continuously, the internal power amplifier section is being excessively overloaded and may malfunction. CAUTION Applying reverb or echo to the sound Reverb recreates the warm ambience of an actual performance space, such as a concert hall or a night club. For each channel you want to apply reverb, set the corresponding REVERB switch to ON（... - Page 9 AC IN JACK Connect the included power cord here. Be sure to use the included power cord. Use of other cords may result in malfunction, heat generation, or fire. CAUTION POWER switch For turning the power to the mixer on and off. SPEAKERS L/R jacks (for included speakers only) These output the mixed signal channels from 1 to 7/8, and the level is adjusted with the MASTER LEVEL control.
- Page 10 (this booklet), and an optional microphone and the cable. Remove the real panel of the speaker and put in the things you need. Carry the PC8MA/PC10MA with you, and you’ve got all you need to set up and perform—anywhere, anytime.
-
Page 11: Connection Example
Connection Example Connection Example The PC8MA/PC10MA can be used in a wide variety of sound reinforcement applications, from a full-band performance onstage to solo street performance-providing a powerful, high-performance system in an exceptionally compact and portable package. Connect a guitar or a microphone to the monaural input jacks (channels 1to 4) and connect a keyboard to the stereo input jacks (channels 5/6 to 7/8). - Page 12 PC8MA / PC10MA www.soundbarrier.com...
Need help?
Do you have a question about the PC8MA and is the answer not in the manual?
Questions and answers