Advertisement
Quick Links
Bentintoshape llc
Installation and Operation
Fire Pit - Remote Tank
INTRODUCTION
Your bentintoshape Cor-Ten Steel
Gas Fire Pit is designed for installation in a
fully vented, open air patio area which is
constructed of non-combustible material.
See page 9 for installation on wood deck.
Do not place this appliance on a grass or dirt
area. This may prevent proper safety venting.
This appliance is designed as an
"attended appliance". Adults must
be present when the unit is operating.
DO NOT leave this unit burning when
unattended. If this product is left
burning unattended it may cause
damage, serious injury
OR LOSE OF LIFE.
GENERAL INFORMATION
These instructions are intended as a general
guide and do not supersede national or local
codes in any way. Authorities having
jurisdiction should be consulted before
installation.
Installation and provision for combustion and
ventilation air must conform with the National
Fuel Gas Code.
IMPORTANT !
Read all instructions carefully before starting
installation. Failure to follow these installation
instructions may result in a possible fire hazard
and void the warranty.
WARNING !
For outdoor use only. Do not use for cooking.
CUSTOMER CARE
For any replacement parts or questions please
contact customer care at 1-888-226-0658
Bentintoshape llc - Fire Pit Instruction Manual
Published 1/1/11
Instructions
Cor-Ten Steel Maintenance ..............8
WHAT TO DO IF YOU SMELL
Shut off gas supply to the appliance.
DO NOT ATTEMPT TO LIGHT THE
APPLIANCE!
Do not touch any electrical switch.
Do not use a cell phone in the area.
Extinguish any open flames.
Immediately call your gas supplier. Follow
the gas supplier's instructions.
If you can not reach your gas supplier, call
the fire department
!!!WARNING ! !!
Improper installation, adjustment, alteration,
service or maintenance can cause injury or
property damage. Read this manual thoroughly
before installing or servicing this equipment.
A liquid propane tank, not connected for use
with this decorative gas fire pit, shall not be
stored in the vicinity of this or any other
appliance.
This appliance must be used only outdoors in a
well ventilated space and must not be used
inside a building, garage, or any other enclosed
area.
www.bentintoshape.net
Table of Contents
....................2
............................3-5
...........5
...........6
....................6
...........7
....................7
GAS
Advertisement
Summary of Contents for Bentintoshape LP series
-
Page 1: Table Of Contents
For outdoor use only. Do not use for cooking. area. CUSTOMER CARE For any replacement parts or questions please contact customer care at 1-888-226-0658 Bentintoshape llc – Fire Pit Instruction Manual Published 1/1/11... -
Page 2: Safety Information
The LP gas cylinder supply system must be arranged for vapor withdrawal. The LP gas cylinder used must include a collar to protect the cylinder valve Bentintoshape llc – Fire Pit Instruction Manual... -
Page 3: Installation
(shown in Figure 1A and 1B). The fire pit is completely assembled to the key valve. Check to make sure there is no damage to Bentintoshape llc – Fire Pit Instruction Manual the line from the burner ring to the key valve. - Page 4 LP/NG MODEL - NATURAL WOOD/CERAMIC LOG MEDIA Fire Ring Media grate 38” ROUND/ SQUARE MODELS 30” ROUND MODEL Gas On/Off Valve Key valve accepts ½”male pipe Air/Gas Defuser thread source connection. (Propane Only) FIGURE 1B Bentintoshape llc – Fire Pit Instruction Manual...
-
Page 5: Operating Instructions
4. WHEN LIGHTING FIRE PIT, ONLY OPEN KEY VALVE SLIGHTLY. ALWAYS PLACE MATCH NEAR CENTER ORIFICE PRIOR TO OPENING KEY VALVE. Bentintoshape llc – Fire Pit Instruction Manual... -
Page 6: Lighting Instructions
For an LP appliance, turn the key valve appliance turn the key valve completely completely clockwise to the closed position clockwise to the closed position. and then turn the valve on the LP tank clockwise to the closed position Bentintoshape llc – Fire Pit Instruction Manual... -
Page 7: Maintenance Instructions
Clean burner ports Faulty valve Replace Valve Faulty Regulator eplace Regulator High Altitude Adjust orifice size for altitude Backfire of burner Blocked orifice Check orifice opening Clogged or dirty burner ports Clean burner ports Bentintoshape llc – Fire Pit Instruction Manual... -
Page 8: Cor-Ten Steel Maintenance
NOTE: Do not get water into any of the burner components. Water in the burner components can cause dangerous back pressure. If you think there is water in the burner components, call a licensed technician to check the burner components prior to use. Bentintoshape llc – Fire Pit Instruction Manual... - Page 9 Figure 3A is an example of a acceptable heat and fire barrier for a glass media/lava rock configuration fire pit. Always check with local code prior to installation of any heat and fire barrier. Bentintoshape llc – Fire Pit Instruction Manual...