Related Manuals for Nidec SUNVS4
Summary of Contents for Nidec SUNVS4
- Page 1 SWIMMING POOL PUMP FOR POOLS AND SPAS OWNER’S MANUAL 59926-XXXX 877.278.2797 fax 888.610.3839...
-
Page 2: Table Of Contents
Owner’s Manual Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference. -
Page 3: General Safety Information
General Safety ELECTRICAL HAZARDS in the motor trips or if the GFCI trips A licensed electrician, experienced in determine the reason and correct the Information (Cont.) swimming pools and spas, should inspect problem before re-starting pump. Always follow basic safety precautions your equipment to make sure everything is •... -
Page 4: Threaded Connections
Owner’s Manual Installation (Cont.) ENTRAPMENT PROTECTION connection to pipe. The suction line is The pump suction must be designed to also designed to accept 3 in. NPT external water system. The pump is only designed for threaded connection. For best results use eliminate the possibility of suction entrap- pool or spa installation. -
Page 5: Electrical
Electrical WIRING Failure to tighten clamp ring as indicated will reduce product strength, resulting in Follow all national and local wiring codes. A Ground Fault Circuit Interrupter (GFCI) failure of components, and bodily injury. If unsure of code requirements consult a is required in the circuit. -
Page 6: Draining Pump
Owner’s Manual Maintenance indicating the power is to remain OFF. (Cont.) 9. Then grasp impeller and rotate counter- • CLOSE GATE VALVES in suction and clockwise to remove impeller from shaft. Hazardous suction discharge pipes. 10. Pull mechanical seal rotating assembly can trap hair or body •... -
Page 7: Troubleshooting Guide
Maintenance 7. Replace main seal plate o-ring with (Cont.) Some safety vacuum a new one. Clean the surface before release system Stationary installing. (SVRS) devices are not compatible with o-ring installation of check valves. If the pool 8. Slide rotating assembly back into has an SVRS device, be sure to confi... -
Page 8: Swimming Pool Pump
Owner’s Manual Swimming Pool Pump Flow Rates... -
Page 9: Notes
Notes... - Page 10 Owner’s Manual For replacement parts or technical assistance, call 1-877-278-2797 Please provide following information: - Model number - Serial number - Part description and number as shown in parts list...
-
Page 11: Replacement Parts List
Replacement Parts List Ref. Description Part Number Qty. Machine Screw 3/8-16 x 1.00 UNC 2A 4383 Base Screw 4951 Machine Screw 10-32 x 1/2 UNC 2A 08831 Machine Screw 1/4-20 x 1 UNC 2A Left Handed 14052 Diffuser O-Ring 19014-001 Strainer Basket O-Ring 19084-001 Housing O-Ring... -
Page 12: Warranty
Owner’s Manual Limited Warranty ( ) year from the date of purchase, the manufacturer will repair or replace, at its option, for the original owner any parts of its pumps (“Product”) which are found upon examination by the manufacturer to be defective in materials or workmanship. - Page 13 INSTALLATION AND MAINTENANCE MANUAL For Non-SVRS Models Programmable Pool Pump Motor/Control This Product Does NOT Provide A Safety Vacuum Release System (SVRS). Save this instruction manual for future reference. M017898010000 REV: August 31, 2012...
- Page 16 Always disconnect electrical power at the fuse box or circuit breaker before handling electrical connections. Double check to be sure Power is OFF, and that it cannot be turned on while you are working on the equipment.
- Page 18 A properly functioning motor may be too hot to touch and can cause injury.
- Page 21 Run/Stop button. This button is used to activate or stop the unit operation. The button will illuminate when in Run mode. This button does not disconnect power to the unit. Press the Enter button to confirm and save your selections. Use the arrow keys for menu navigation purposes and to change values.
- Page 22 Run/Stop button. This button is used to activate or stop the unit operation. The button will illuminate when in Run mode. This button does not disconnect power to the unit. Press the Enter button to confirm and save your selections. Use the arrow keys for menu navigation purposes and to change values.
- Page 23 The “Press ENTER to Confirm” icon illuminates when the unit requests you to confirm your selection. The Attentionsection displays important operating information regarding your unit. Detailed information on these items can be found in The Fault section of this manual – Pages 24-25. sional.
- Page 24 Each Menu Option has its own programming procedure. See Pages 13-17. P re ssin g th e “ ” b u tto n w ill P re ssin g th e “ ” bu tto n w ill e n te r th e M e nu O p tion s le vel. P re ssin g P rogram re tu rn th e u nit to R u n m o d e E xit...
- Page 34 How it works:...
- Page 36 Pool Cleaners with Booster Pumps: Pool Cleaners without Booster Pumps: Heaters:...