Related Manuals for Aimco UDBP-T40
Summary of Contents for Aimco UDBP-T40
- Page 1 UDBP-T Series 40, 50, 60 & 70 Lithium Ion Battery-powered Direct Drive Auto-shutoff Pulse INSTRUCTION MANUAL PO Box 16460, Portland, OR 97292-0460 503-254-6600 Fax 503-255-2615 - 1 -...
-
Page 2: For Safety Operation
Indicates a critical operating step that must DANGER be followed. Carefully read this instruction for safe use, understand the contents, and use the tool properly. Keep this manual. Indicates that incorrect handling may create a CAUTION hazardous condition, resulting in injury to an operator or physical damage to the tool. - Page 3 DANGER 4. Do not allow unauthorized persons at the worksite. Tool should be used by trained adult personnel and kept away from all children. 5. Use correct charger, power cord, and battery with this tool. Do not charge the battery by other charger. Do not use our charger for other maker’s batteries.
- Page 4 DANGER 11. Release your finger from the trigger, and remove the battery from the tool whenever performing the following: ・ Torque adjustment. ・ Replace driver bit or socket. ・ Repairing the tool. 12. Wash your eyes should any battery liquid get to your eyes, and have your eyes examined and medically treated by an eye care doctor immediately.
- Page 5 CAUTION 1. Proper fastening time ・ Battery pulse tool will allow tightening an average of 6 cycles per minute when averaged on a B joint. Softer joints will require less aggressive duty cycles. ・ Temperature protection will function to stop the tool when motor heats due to exceeding duty cycle.
- Page 6 CAUTION 4. Cautions for tool’s operation ・ Confirm that no person interferes with work environment or is in a hazardous position. ・ Stop the operation at once, and request service if abnormalities are found with the tool’s operation. 5. Do not do recklessly handle the power cord of the charger. ・...
- Page 7 CAUTION 11. Overload protect function of motor ・ This function will work to stop the motor when the anvil becomes locked for about 1 second with the trigger depressed. 12. Use appropriate tool whose capacity can cover the requirements of your work.
- Page 8 CAUTION 18. Do not give battery shock due to drops. Do not throw batteries. Doing so will deform batteries, destroy integrated protection circuit, can result in a charge of the battery by abnormal current or voltage resulting in damage or injury. 19.
-
Page 9: Parts Name
Parts Name Shut-off LED Lamp Torque Adjust Allen Wrench Trigger Reverse Lever Battery Specifications Ambient temperature: 0 ～ 4 0 ℃ Rotating speed change: 3 steps Slow speed: 500rpm → 1 ,000rpm for socket and bolt entry and tentative fastening Free speed: 4,800rpm for regular fastening - 9 -... -
Page 10: Handle Controls
Handle Controls Select rotating direction (factory supplied lever orientation) １ １ １ １ Trigger Reverse lever Set LEVER to R ： Forward Set LEVER to L ： Reverse Press trigger ２ ２ ２ ２ 1 ） Speed increases in 3 steps as you press the trigger progressively for both forward and reverse. - Page 11 Handling point Torque adjustment in forward rotation (CW) only ４ ４ ４ ４ ・ Release hands from trigger, then remove the battery from the tool. ・ Insert an allen key in the hole to adjust relief valve as follow. ・ Never touch oil plug. Removal of oil plug will result in leakage and tool requiring service.
-
Page 12: Handle Operation
Remove allen Handle Operation bolt Changeable Fwd/Rev Lever (if desired) ５ ５ ５ ５ Ｒ ： F orward Ｌ ： R everse （ Ｒ ） （ Ｌ ） Pull forward （ Ｌ ） （ Ｒ ） Reverse lever １ ） Remove allen bolt (use 2mm hexagon bar spanner). ２... - Page 13 Handling point Press the trigger and the LED will light in white. ７ ７ ７ ７ Avoid staring at LED. CAUTION Factors that affects fastening torque １ １ １ １ Fastening torque can change even for the same size bolt because of torque coefficient determined by finishing status of the bolt or the work such as industrial quality ranking of the bolt or the length.
-
Page 14: Battery Charger
Battery charger UDBP utilizes lithium ion battery. Battery replacement interval １ １ １ １ Batteries may be charged up to 500 times after full discharge. This number ・ of times can change depending upon the operating conditions. Consider that the battery has come to an end and replace with a new one when number of fasteners per full charge gets about a half of new battery condition. - Page 15 Battery and the charger Charge brand-new battery completely before first use of the tool. Suspension of battery charging prematurely can cause the LED to incorrectly display remaining capacity ( ＊ 2 ). ( ＊ 2 ): Charge the battery full 2 to 3 times and the display will get back to normal.
-
Page 16: Troubleshooting
Troubleshooting Check the following before you ask for repair. When Charging Symptom Potential Cause Remedy Charge only room Waiting lamp lights Battery is overheated temperature batteries Battery is damaged or at Replace the battery with Battery error lamp lights. the end of it’s service life a new one. -
Page 17: Maintenance
Maintenance DANGER 1 Check for any loose parts, breakage, or wear of all parts prior to each use. CAUTION 1 Maintenance ・ C asing is made of plastic. Wipe it by soft cloth. Do not use volatile liquids or wet cloth because doing so will cause deterioration/discoloration of the materials. - Page 18 Notes:__________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ - 18 -...
- Page 19 - 19 -...
- Page 20 Corporate Headquarters 10000 SE Pine Street Ave. Cristóbal Colon 14529 Portland, OR 97216 Chihuahua, Chihuahua. 31109 800-852-1368 Mexico FAX 800-582-9015 011- 52-(614) 380-1010 www.aimco-global.com FAX 011-52-52 (614) 380-1019 LIT-MAN950 Rev. 12/2010 Printed in USA ©2010 AIMCO - 20 -...
Need help?
Do you have a question about the UDBP-T40 and is the answer not in the manual?
Questions and answers