1. Manuals
  2. Brands
  3. Masalta Manuals
  4. Cutter
  5. MF16
  6. Operation manual

Masalta MF16 Operation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
OPERATION MANUAL
CONCRETE CUTTER MF16
!
WARNING
To reduce the risk of injury, all operators and maintenance personnel must read and understand these
instructions before operating, changing accessories, or performing maintenance on Masalta power
equipment. All possible situations cannot be covered in these instructions. Care must be exercised
by everyone using, Maintaining or working near this equipment.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MF16 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Masalta MF16

  • Page 1 To reduce the risk of injury, all operators and maintenance personnel must read and understand these instructions before operating, changing accessories, or performing maintenance on Masalta power equipment. All possible situations cannot be covered in these instructions. Care must be exercised...

  • Page 2: Table Of Contents

    RULES FOR SAFE OPERATION influence or drugs or alcohol. General Safety …………………………………….1-2 ¡ ö NEVER use accessories or attachments, Diamond Blade Safety ……………………….……..2 which are not recommended by MASALTA Cutter Transportation Safety ………………….……2 this equipment. Damage Emergencies …………………………………………3 equipment and/or injury to user may result.

  • Page 3: Diamond Blade Safety

    and cleanliness before mounting blade. ¡ ö NEVER use fuel as a cleaning agent. Blade should fit snugly on the shaft and ¡ ö ALWAYS read, understand, and follow procedures in against the inside/outside blade flanges. operator’s Manual before attempting to operate ¡...

  • Page 4: Emergencies

    EMERGENCIES asphalt with a concrete cutter. Our MF16 ALWAYS know the location of the nearest fire ¡ ö utilized for jobs requiring precision cutting extinguisher and first aid kit. Know the location of the including floors, pavements, walkways, ramps nearest telephone. Also know the phone numbers of and other flat sawing applications.

  • Page 5: Installing Blade

    INSTALLING BLADE engine, to run. Open the throttle approximately half way and apply the choke. Pull the starter 1. Be certain that the spark plug is disconnected or saw rope sharply. When the engine starts, open the is unplugged. choke and adjust the throttle as necessary to 2.

  • Page 6: Cutting

    Cutting/Belts & Pulleys CUTTING Lower the blade into concrete to required depth by turning the tilt crank counterclockwise. Ease the saw slowly forward. Slow forward pressure if the saw begins to stall. Note: For deeper cuts (4 inches/102mm or more), several cuts should be made in incremental steps of 1-1/2 inch (38mm) to 2 inches (51mm) until the desired depth is reached.

  • Page 7: Troubleshooting

    MAINTAINENACE - TROUBLESHOOTING PROBLEM CAUSE REMEDY UNEVEN SEGMENT WEAR (In wet cutting) Insufficient water Flush water system. ¡ ñ ¡ ñ (usually on one side of blade). Check flow to both sides of blade. ¡ ñ Equipment defects also can cause Replace bad bearings, worn arbor ¡...
  • Page 8 MAINTAINENACE - TROUBLESHOOTING PROBLEM CAUSE REMEDY BLADE WOBBLES Blade is on a damaged or Check for bad bearings, bent shaft, ¡ ñ ¡ ñ worn saw. or worn mounting arbor. Worn collar. Check collars/flanges to make sure ¡ ñ ¡ ñ Blade runs at an incorrect speed.

  • Page 9: Lubrication And Service

    LUBRICATION AND SERVICE ¢ ô ¢ õ SEPECIFICATION ¡ ñ Check oil levels, wiring, hoses (air, fuel, water) and Motor lubricate machine daily. MF16-1 Diesel, 186 7.5kw output ¡ ñ Repair replace worn damaged MF16-2 Petrol, 188F 9.8kw output components immediately.
  • Page 11 MF16 PARTS LIST 1 ITEM ITEM PART NO. DESCRIPTION PART NO. DESCRIPTION 05780012 BOLT M12X20-GB5780 00180902 BEARING & BRACKET 09300012 SPRING WASHER 12-GB93 01096008 KEY C8 X 38 - GB1096 18030104 DEEP WASHER 18090002 PRINCIPAL AXIS 00180303 RUBBER WHEEL ( REAR)
  • Page 13 MF16 PARTS LIST 2 ITEM NO. PART NO. DESCRIPTION 00180006 PLASTIC PIPE 00180005 TEE PIPE 00180002 COCK 18050006 ELBOW BEND 00180501 00180502 18050011 ELBOW 18050000 WATER TANK 00180009 THROTTLE CABLE 00180010 THROTTLE CONTROL 00180011 HANDLE BAR GRIP 18060000 HANDLE LEVER...
  • Page 14 Add:RM 501, Fortune Plaza, No.278 of Suixi Rd., Hefei 230041,China Tel: 86-551-5609770, 5609780 Fax: 86-551-5609010, 5621707 E-mail: masalta@mail.hf.ah.cn Http://www.masalta.com.cn Version: 01/05...

Table of Contents