Subscribe to Our Youtube Channel
Related Manuals for Baxall HYPER-D Series
Summary of Contents for Baxall HYPER-D Series
- Page 1 HYPER-D Series Cameras Installation Instructions Please read these instructions first!
- Page 2 Hyper-D Series Installation Instructions IMPORTANT The first few pages of these instructions contain important information on safety and product conformity. Please read, and ensure that you understand this information before continuing.
- Page 3 Installation Instructions Hyper-D Series INTRODUCTION These instructions cover Baxall Hyper-D series cameras. Read all of these instructions. Use them to install your camera and have them available for its lifetime. If you have any problems, contact Baxall Limited. FEATURES The Hyper D camera range has been designed to function with the minimum of set up. The default settings of the camera should be able to cope with most applications.
-
Page 4: Product Safety
Good engineering practice must be carried out at all times and all servicing and repairs carried out indoors. • Hyper-D series cameras are to be powered with a class 2 power supply. • Under no circumstances must the power consumption of the Auto Iris connector exceed 50 mA or the Direct Drive connector exceed 25 mA. -
Page 5: Connectors And Controls
Installation Instructions Hyper-D Series CONNECTORS AND CONTROLS 7. Menu up button 1. Low-voltage power supply terminals 8. Enter button 2. Composite video output BNC 9. DD/Video Lens conector 3. Power LED 10.Back focus adjustment screws 4. Decrease parameter button 11.Video format selector switch 5. -
Page 6: Video Connection
Hyper-D Series Installation Instructions VIDEO CONNECTION FOCUS ADJUSTMENT Turn the back focus adjuster screw (10, figure 1) clockwise or anticlockwise to obtain focus. When the focus is sharp, turn the adjustment screw 2 or 3 turns anticlockwise. The picture will lose sharpness. Turn the screw clockwise until focus is once again obtained. If you pass the point of best focus, repeat the procedure. -
Page 7: Menu System
Installation Instructions Hyper-D Series MENU SYSTEM Hyper-D series cameras utilise a menu system to facilitate setup and adjustment. The buttons used to access and navigate the menu are located behind the flap on the side of the camera. Entering the Menu System To enter the menu system, press and hold the Enter button (8, figure 1) for approximately two seconds. - Page 8 Hyper-D Series Installation Instructions MODE NORMAL The default setting provides maximum dynamic range and is suitable for high-contrast scenes. REDUCED DR This setting limits the dynamic range. This can provide higher contrast images when not viewing wide-dynamic scenes. AI LENS SET This setting allows you to set the lens level on a video Auto Iris lens.
- Page 9 Installation Instructions Hyper-D Series MOTION This setting has a maximum gain of 24dB. This setting does not use DNR at high gain. The images are sharper than DNR but the visible gain in the image is greater. WHITE BALANCE RANGE This menu is used to adjust the camera’s white balance to compensate for different lighting...
- Page 10 Hyper-D Series Installation Instructions SYNC This menu is used to select the way the camera maintains frame synchronisation. MODE NORMAL WHITE BALANCE RANGE FLUORESCENT > SYNC <INTERNAL> SAVE AND EXIT INTERNAL For internal synchronisation. PHASE 1, PHASE 2, PHASE 3 When synchronising multiple Hyper-D cameras in a three-phase installation.
-
Page 11: Specifications
Installation Instructions Hyper-D Series SPECIFICATIONS Horizontal resolution >480 TVL Vertical resolution >400 TVL Dynamic range 95 dB (14-bit) typical; 120 dB max. Video Output Composite 1V pk-pk 75 Ohm Pixel type DPS™ technology Image size 6.3mm diagonal (type 1/3”) Sensor array size 5.04mm (H) x 3.78mm (V) - Page 12 Baxall Limited, Stockport, England. Visit our Web site: http://www.baxall.com Baxall Limited reserve the right to make changes to the product and specification of the product without prior notice to the customer. HB-HYPER-D-1 Issue 1 01/04...
Need help?
Do you have a question about the HYPER-D Series and is the answer not in the manual?
Questions and answers