Table of Contents
Advertisement
Table of Contents
1
Introduction ..................................................................... 2
1.1 Pictograms ................................................................2
1.2 Notes on Use of this Handbook ....................................3
2
Safety Notes ..................................................................... 3
2.1 General Safety Notes..................................................4
2.2 End of Life ................................................................5
3
Technical Specifications .................................................... 7
3.1 Machine Rating Sheet .................................................7
3.2 Machine Specification .................................................8
4
Machine Layout Guide ....................................................... 10
4.1 Description of Machine ...............................................10
5
Parts Identification ........................................................... 11
6
Control Panel .................................................................... 12
7
Operating Overview .......................................................... 13
8
Set Up ............................................................................... 14
9
Double Document Calibration ........................................... 18
10
Handfeed .......................................................................... 18
11
Operator Maintenance ...................................................... 19
12
Supervisor Mode ............................................................... 24
13
Operator's Troubleshooting Guide .................................... 25
14
Error/Status Messages ..................................................... 26
Issue 5 January 2012
8.1 Loading the Paper Hopper ........................................14
8.2 Setting the Fold Plates .............................................14
8.2.1 Fold Plate 1 ......................................................14
8.2.2 Fold Plate 2 ......................................................15
8.2.3 Using V-folds ....................................................15
8.2.4 Fold Options .....................................................16
11.1 Cleaning the Fold and Seal Rollers ...........................19
11.2 Cleaning the Sensors .............................................21
11.3 Clearing Paper Jams ..............................................22
LM-5.5 Operator Manual
LM-5.5 Operator Manual
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Lasermate LM-5.5
-
Page 1: Table Of Contents
LM-5.5 Operator Manual Table of Contents Introduction ..............2 1.1 Pictograms ..............2 1.2 Notes on Use of this Handbook ........3 Safety Notes ..............3 2.1 General Safety Notes..........4 2.2 End of Life ..............5 Technical Specifications ............ 7 3.1 Machine Rating Sheet ..........7 3.2 Machine Specification ..........8... -
Page 2: Introduction
LM-5.5 Operator Manual INTrODUCTION With this pressure sealer you have an advanced, medium-volume pressure sealing machine. Two sets of fold rollers provide secure sealing on all edges and its ease of operation makes it the ideal complement to the small-office environment. In order to ensure the long usage of this machine and its components, and above all the safe use of the machine, you must read and adhere to the operating instructions and safety notes. -
Page 3: Notes On Use Of This Handbook
LM-5.5 Operator Manual 1.2 Notes on the Use of this Handbook This document contains all general information and explanatory text necessary in order to be able to carry out the operation of the machine. When some action is expected from the operator, this will always be explicitly stated, and where relevant, accompanied by an illustration or graphic. -
Page 4: General Safety Notes
LM-5.5 Operator Manual General safety notes Caution! Please, read these notes with care. Save these instructions for later use. All notes and warnings found on the machine are to be followed. Installing Important! The machine must be installed on a suitably strong surface. - Page 5 LM-5.5 Operator Manual Spare Parts When repair work is carried out, only original spare parts or spare parts corresponding to the original parts may be used. Repairs Do not disassemble the machine any further than is described in this handbook. Other than the top cover, the opening of the machine by unauthorized personnel is not permitted.
-
Page 6: End Of Life
LM-5.5 Operator Manual End of Life The objectives of the European Community’s environment policy are, in particular, to pre- serve, protect and improve the quality of the environment, protect human health and uti- lise natural resources prudently and rationally. That policy is based on the precautionary principle and principles that preventive action should be taken, that environmental damage should as a priority be rectified at source. -
Page 7: Technical Specifications
LM-5.5 Operator Manual TECHNICaL SPECIfICaTION Machine rating sheet CAUTION: In order to ensure correct safety and operation, this machine must only be installed and maintained by an authorized Service Engineer. CAUTION: Should any cover or safety interlock be damaged, the machine must not be used until service repairs have been completed. -
Page 8: Machine Specification
LM-5.5 Operator Manual 3.2 Machine specifications form Size: Standard Lengths: 11”, 11.69”, 12” & 14” Standard Widths: 8.27” & 8.5” fold Types: Standard V-fold: 8.5 x 11” Standard C-fold: 8.5 x 11” Standard Z-fold: 8.5 x 11”, 8.5 x 14” Eccentric Z-fold: 8.5 x 11”... - Page 9 LM-5.5 Operator Manual Physical Dimensions: Length: 23 ¾”, tray retracted 29 ¾”, tray extended Width: 17.5” Height: 18.5” to top of fold plate footprint: 15” long x 17.5” wide Weight: 140lbs Electrical: Voltage: 115V @ 60Hz Current: 2.5A Noise Level: 75dBA (Based on A4, Z-fold, 90gsm paper, measured at 1.6m height, 1m from nearest cover).
-
Page 10: Machine Layout Guide
A jog function is provided, which operates the machine in short ‘spurts’ in order to help clear The function of the LM-5.5 Pressure Sealer jammed forms through the paper path. A jam- is to feed unfolded forms from a stack, fold... -
Page 11: Parts Identification
LM-5.5 Operator Manual ParTS IDENTIfICaTION Shown below are the main areas of the LM-5.5 Pressure Sealer. Button for fold Paper hopper roller access Fold plate 2 adjustor Fold plate 2 Fold plate 1 Fold plate 1 adjustor Control panel Receiving tray... -
Page 12: Control Panel
LM-5.5 Operator Manual CONTrOL PaNEL Zero reset Display button Stop button Calibration/ Run/jog jog back- forward ward button button Button/Item Description Button/Item function Zero reset button: Sets the forms count on the display to zero. (Press again to restore count). -
Page 13: Operating Overview
LM-5.5 Operator Manual OPEraTING OVErVIEW Shown below is an operating summary of the machine. Further details may be found in the section indicated. aCTION PaGE Plug in the machine and switch on. Load paper into the paper hopper. Extend the receiving tray. This may be set to accommodate the size of the folded form. -
Page 14: Set Up
LM-5.5 Operator Manual SET UP Loading the paper hopper Fan a stack of forms (max. 350) and align the edges. Adjust the width of the side guides to give approx, 1/32" Press down on the tray and load clearance on the forms. -
Page 15: Fold Plate 2
LM-5.5 Operator Manual 8.2.2 fold Plate 2 Loosen the knob and adjust the stop so that the bottom edge of the backstop plate aligns with the scale measurement of the 2nd. fold length (see section 8.2.4). Retighten the knob. Scale (inches or cm) 8.2.3... -
Page 16: Fold Options
LM-5.5 Operator Manual 8.2.4 fold Options Indicated below are the three types of folds that may be used. Use the arrow as a guide to which way the paper should be stacked on the tray; normally the address will be on the same side and at the same end as the arrow. - Page 17 LM-5.5 Operator Manual frequently used form Sizes The list shown below indicates the Fold Plate settings for some typical folded forms.
-
Page 18: Double Document Calibration
LM-5.5 Operator Manual DOUBLE DOCUMENT CaLIBraTION Each time the machine is run, it will automatically calibrate the first form to measure its size and thickness. Thereafter, if two forms are fed at the same time, they will be ejected through the slot below fold plate 2 before reaching the sealing rollers. If the paper size or weight is changed without switching off, it is advisable to use the cali- bration button to calibrate again, as shown below. -
Page 19: Operator Maintenance
LM-5.5 Operator Manual operator maintenance After a long period of use, dirt and toner can build up on the fold and seal rollers, and dust can cause the sensors to become obscured. This will need to be cleaned off to ensure reli- able operation. - Page 20 LM-5.5 Operator Manual rear Seal roller The rear seal roller is accessed by press- ing the button on top of the machine, then lowering the cover and hinging the inner chassis open. Clean the full width of the two rollers using the same fluid as the fold rollers. Rotate the roller as for the front rollers above until it is fully cleaned.
-
Page 21: Cleaning The Sensors
LM-5.5 Operator Manual 11.2 Cleaning the Sensors The optical sensors on the machine consists of two halves, spaced slightly apart. They should be cleaned at regular intervals using only a non-flammable airduster (part number 9103707C or equivalent), ensuring that both halves are cleaned. Do not use a liquid solvent on the sensors. -
Page 22: 11.3 Clearing Paper Jams
LM-5.5 Operator Manual 11.3 Clearing Paper Jams If paper jams occur, they can usually be cleared by using the jog function or jam clearance lever. The jog function operates the machine in short spurts to drive out the jammed docu- ment in a controlled manner. - Page 23 LM-5.5 Operator Manual Cleaning rollers If you are using the jog function to clean rollers, it will be necessary to force a fault before the function will operate. To do this, simply remove all paper from the machine and press the Run button - after a few seconds, an out of paper fault will be flagged and the jog func- tion can be used.
-
Page 24: Supervisor Mode
LM-5.5 Operator Manual SUPErVISOr MODE Supervisor Mode reveals various statistics about the machine, namely Eprom version num- ber, total running hours and overall forms count. To enter the mode, press the Stop button while the machine is displaying the 'HELLO' message after switching on. The message 'SU- PErViSOr' on the display indicates that the mode has been entered. -
Page 25: Operator's Troubleshooting Guide
LM-5.5 Operator Manual OPEraTOr’S TrOUBLESHOOTING GUIDE If problems occur, refer to the guide shown below before contacting the Service De- partment. problem SuggeSted cauSe and remedy 1. Machine will not run. 1. Ensure emergency stop button is not depressed and that power cord is plugged into power outlet. -
Page 26: Error/Status Messages
LM-5.5 Operator Manual ErrOr/STaTUS MESSaGES If operating faults occur, a code will appear on the control panel display, for example: where 'nn' = one of the numbers indi- cated below. The fault code will alternate with a scrolling description of the problem. If more than one fault has caused the machine to stop, each code and description will cycle through before repeating.
Need help?
Do you have a question about the LM-5.5 and is the answer not in the manual?
Questions and answers
Why does the form not feed? The roller turn but the document does not feed.
The Lasermate LM-5.5 may not feed documents even though the roller turns due to improperly loaded forms. Ensure that the leading edges of the forms are firmly against the chassis bridge and that the tray is properly depressed.
This answer is automatically generated