Summary of Contents for LOHBERGER THermo Insert independent
- Page 1 THermo Insert independenT of indoor air dependenT on indoor air O peratI ng M an ua l wi t h in sta ll at io n in st r u ct i on s Issued January 2012...
-
Page 2: Table Of Contents
1. Safety instructions ..............................3 2. important instructions prior to installation and start-up ...................4 3. Transport / Unpacking / inspection ..........................5 4. important standards / guidelines ..........................5 5. Special notes ................................5 6. design of the appliance ............................6 7. Fuels ..................................7 8. Chimney / Flue pipe connection ..........................7 9. -
Page 3: Safety Instructions
With the above in mind, we are convinced that this appliance will give satisfactory service for many years. Your LoHBerGer Heiz + Kochgeräte Technologie GmbH During combustion, wood only emits the same amount of CO2 that it previously held as a tree. -
Page 4: Important Instructions Prior To Installation And Start-Up
2. Important instructions prior to installation and start-up 2. Important instructions prior to installation and start-up Correct installation and Start-up Before connecting the appliance to the chimney, Before connecting the appliance to the chimney, inform the local qualified chimney sweep. inform the local qualified chimney sweep. -
Page 5: Transport / Unpacking / Inspection
3. Transport / Unpacking / Inspection 3. Transport / Unpacking / Inspection the packaging of your appliances provides good protection against damage in Report visible faults to the supplier immediately. Report visible faults to the supplier immediately. transit. nevertheless, damage to the appliance and fittings cannot be entirely Later claims for damages cannot be entertained. -
Page 6: Design Of The Appliance
6. Design of the appliance 6. Design of the appliance sheet-metal panelling black Combustion chamber door body (only with appliance type „Design sheet-metal Combustion chamber door sealant panelling“) Combustion chamber door viewing glass Combustion chamber door Combustion chamber door latch Fuel drawer Decorative glass inlay of fuel drawer Connection at the top... -
Page 7: Fuels
7. Fuels 7. Fuels Suitable fuels FireWood (LoGS) Firewood (Figure 4) should have a moisture content of approx. 20 % of the dry weight, a length of 1/3 m and should be split into small pieces. this way, the firewood quickly catches fire and produces a higher heat output than the same volume of large logs. -
Page 8: Air Supply For Combustion With Dependence On Indoor Air (Open-Flued Appliance)
9. Air supply for combustion WITH dependence on indoor air 9. Air supply for combustion WITH dependence on indoor air (open-flued appliance) (open-flued appliance) Air supply for combustion via the room where the appliance is Negative pressures in the room where the ap- Negative pressures in the room where the ap- pliance is located (e.g. -
Page 9: Air Supply For Combustion Not Dependent On Indoor (Room-Sealed Appliance)
10. Air supply for combustion NOT dependent on indoor 10. Air supply for combustion NOT dependent on indoor (room-sealed appliance) (room-sealed appliance) the air for combustion is entirely supplied to the combustion chamber via a supply air pipe of 100 mm diameter (to be provided by the customer). the oval-shaped pipe connection for the combustion air system is located on convection air the cover plate behind the flue gas connection. -
Page 10: Safety Clearances
(measurements in cm) for this pad as shown in Figure 11 must be observed. Biegemaul 30 LOHBERGER ZUSCHNITTMAß SONSTIGE NAME DATUM Heiz + Kochgeräte... -
Page 11: Customer-Supplied Panelling
Figure 12 Under no circumstances does Lohberger assume Under no circumstances does Lohberger assume liability for the installation of the appliance. The liability for the installation of the appliance. -
Page 12: Operation
14. Operation 14. Operation Accessories supplied by the manufacturer to ensure a safe operation of the appliance, it comes with a grate lifter and a cleaning brush. Closing the heating door the door of the thermoInsert is self-closing and self-locking. to open the hea- ting door, press the integrated release button fully while pulling on the door handle. -
Page 13: Start-Up
15. Start-up 15. Start-up after completion of the assembly and connecting work and prior to the first start-up, a few actions are still required: Ö Open the door of the combustion chamber and remove appliance accesso- ries and transportation safety devices. after you have familiarised yourself with the operating procedures for the stove, the first start-up can begin. -
Page 14: Maintenance / Cleaning
16. Maintenance / Cleaning 16. Maintenance / Cleaning regular maintenance and care or cleaning of the appliance, the fuel gas ducts Allow the appliance to cool down before doing Allow the appliance to cool down before doing and the chimney are particularly important for the operational safety, efficiency any cleaning work to avoid coming into con- any cleaning work to avoid coming into con- and maintaining the value of the appliance. - Page 15 Cleaning the flue gas duct Baffles Open the combustion chamber door and remove both flue gas baffles (Figure 17). Clean the flue gas duct as well as the flue with a suitable cleaning tool (brush). after cleaning reinstall the baffles and the baffle plate to their original position.
-
Page 16: Troubleshooting
Austria (Head office) to enable our customer service to deal with repairs and supplying spare parts lOHBerger Heiz u. Kochgeräte technologie quickly and to your satisfaction, we require the following information with your gmbH service request: landstraße 19 •... -
Page 17: Technical Data
20. Type testing / Quality certification 20. Type testing / Quality certification the stove type thermoInsert made by lohberger, which is independent of in- door air, was successfully tested in compliance with the following standards: • DIn en 13240 (room heating appliance for solid fuels) •... -
Page 18: Appliance Dimensions / Appliance Connections
21. Appliance dimensions / appliance connections 21. Appliance dimensions / appliance connections Design „Customer-supplied panelling“ Dimensions in cm exhaust Ø air intake 107* Ø 109,5 52,5 14,3 42,5 36,8* 21,5 * Installation dimensions Design „Sheet-metal panelling“ exhaust Ø air intake 128,5 Ø... - Page 19 Design „Sheet-metal panelling“ + heat-storage block exhaust Ø air intake Ø 52,5 22,5 50,5 Seite 19...
-
Page 20: Warranty
Warranty claims must always be directed to a local lOHBerger specialist dealer or the dealer from whom you have bought the appliance.