SHURflo Water wizard 150 Instructions

SHURflo Water wizard 150 Instructions

Hand pump

Advertisement

Available languages

Available languages

WATER WIZARD

FEATURES

• • • •
Delivers Water in both stroking directions.
• • • •
Retrofits into most existing hand pump installations.
• • • •
"Twist of the Wrist" Hands-Free operation with city water.
• • • •
Easy winterizing and sanitizing.
• • • •
FDA materials.
• • • •
All corrosion resistant materials.
Parts supplied with aftermarket pump, model # 150-001-00:
• • • •
(1) Swivel Barb 1/2" Hose Fitting
(2) Hose Clamps
#
(4)
6 Screws
(1) Sealing Cap
READ ALL INSTRUCTIONS BEFORE STARTING THE INSTALLATION
READ ALL INSTRUCTIONS BEFORE STARTING
READ ALL INSTRUCTIONS BEFORE STARTING
READ ALL INSTRUCTIONS BEFORE STARTING
CAUTION: DO NOT freeze with water in pump. Refer to page 2 for
Winterizing instructions.
CAUTION: DO NOT snap the square trim cover to the pump until the
unit is correctly located and screwed into position.
NOTE: To remove trim plate, slip screwdriver into slot on plate, and
gently pry up on both sides.
The procedure outlined below is for new installations. To install
the spout there must be 2½"
behind the unit (back wall) and there must be 4¾"
interference to the left side of the unit
pump, modifications to the existing hole may be required. Use the template to determine if the
trim cover will cover an existing hole after modifications.
limitations on space. Use of a hole saw allows the easiest and most precise method to make the
cut out.
1. Determine the position and check under the counter for adequate space to mount the pump. Make
certain there is sufficient clearance to rotate the spout when installing. Also, if mounted in a flip galley,
check for proper clearance in both positions for the pump and tubing. Mark layout lines in-line with the
center of the drain, and 2¼"
will allow cleaning between the trim cover and the sink rim.
2. Cut the template
(Page: 3)
lines and hold in place with tape. Mark (pilot drill) the position of the four 1¾"
3. Use a 1¾"
hole saw to cut the four holes. Trim out the remaining material to attain the cut-out
[4.44 cm]
shown on the template
shown.
4. Place the pump in the cut-out and square it to the sink. Squaring up the pump is easier if the trim
cover is placed in position, but DO NOT snap it in place! Mark the four mounting holes and
remove the pump before drilling small pilot holes for
pilot holes may not be necessary. If installing into an existing hole, simply install the supplied
screws into the existing holes.
5. On the water line between the tank and pump a water strainer is recommend. To protect the pump
a 50 mesh screen
(or finer)
*
supplied with after market pump
911-439 Rev. G 5/99
HAND PUMP MODEL 150
TM
#
8-161-00

THE INSTALLATION

THE INSTALLATION
THE INSTALLATION
clearance from the template centerline to any interference
[6.35 cm]
(see template)
from the outer edge of the sink rim. The ¼"
[5.72 cm]
out around the "edge of trim cover." Position the template over the layout
. The trim cover may not cover the hole if enlarged past the size
(bold line)
is necessary, such as the SHURflo Potable Water Strainer
#
150-001-00
SEALING
CAP
from the centerline to any
[12.06 cm]
. If the Wizard is to replace an existing hand
In most installations there are
#
6 hardware*. If using a power screwdriver,
SPOUT
TRIM COVER
3/8"[10mm]
*
1/2" - 14
THREAD
*
*
*
REGULATED
CITY WATER
clearance
[6.35 mm]
holes.
[4.44 cm]
#
170-061-XX
Page: 1 of 4
INLET
FITTING
POTABLE
WATER
TANK

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Water wizard 150 and is the answer not in the manual?

Questions and answers

Summary of Contents for SHURflo Water wizard 150

  • Page 1 5. On the water line between the tank and pump a water strainer is recommend. To protect the pump a 50 mesh screen is necessary, such as the SHURflo Potable Water Strainer 170-061-XX (or finer)
  • Page 2 In no case will the terms of this limited warranty extend beyond two years from the date of manufacture. Warranty claims may be resolved by the nearest authorized dealer service center, or by a SHURflo service center. All returns are to be shipped with charges pre-paid. Package all returns carefully. SHURflo will not be responsible for freight damage incurred during shipping.
  • Page 3 SPOUT INSTALL POSITION 1-3/4" DIA. [4.44 cm] (4 PLACES) 2-1/2" [6.35 cm] EDGE OF CLEARANCE TRIM COVER 2-1/4" [5.72 cm] SUGGESTED 4-3/4" [12.06 cm] CLEARANCE Water Wizard ALIGN TAB TO INSERT SPOUT SHURflo OUTER RIM OF SINK Template...
  • Page 4 à compter de la date de fabrication. Les détails complets de la garantie figurent dans le Bulletin de service SHURflo n°1041. SHURflo se réserve le droit de modifier les caractéristiques ou les prix de ses produits ou d’effectuer des substitutions. 911-439 Rev. G 5/99...

Table of Contents

Save PDF