Makita 9553NB Instruction Manual

Makita 9553NB Instruction Manual

Hide thumbs Also See for 9553NB:

Advertisement

Angle Grinder
MODEL 9553NB
MODEL 9554NB
MODEL 9555NB
I N S T R U C T I O N
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
DOUBLE
INSULATION
M A N U A L
005801

Advertisement

Table of Contents
loading

Summary of Contents for Makita 9553NB

  • Page 1 Angle Grinder MODEL 9553NB MODEL 9554NB MODEL 9555NB 005801 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
  • Page 2: Specifications

    SPECIFICATIONS Model 9553NB 9554NB 9555NB Wheel diameter 100mm (4”) 115mm (4-1/2”) 125mm (5”) No load speed (RPM) 11,000/min 10,000/min 10,000/min Overall length 258 mm (10-1/8”) 258 mm (10-1/8”) 258 mm (10-1/8”) Net weight 1.4 kg (3.1 lbs) 1.4 kg (3.1 lbs) 1.4 kg (3.1 lbs)
  • Page 3 5. Avoid body contact with grounded sur- 14. Use safety equipment. Always wear eye faces such as pipes, radiators, ranges and protection. Dust mask, non-skid safety refrigerators. There is an increased risk of shoes, hard hat, or hearing protection must electric shock if your body is grounded.
  • Page 4: Specific Safety Rules

    24. When servicing a tool, use only identical SERVICE replacement parts. Follow instructions in 23. Tool service must be performed only by the Maintenance section of this manual. qualified repair personnel. Service or main- Use of unauthorized parts or failure to follow tenance performed by unqualified personnel Maintenance instructions may create a risk of could result in a risk of injury.
  • Page 5 14. Before using the tool on an actual work- cracked or damaged wheel immediately. Run the tool (with guard) at no load for piece, let it run for a while. Watch for about a minute, holding tool away from vibration or wobbling that could indicate others.
  • Page 6 SYMBOLS USD201-2 The followings show the symbols used for tool. V ....... volts ....no load speed ˚ A ....... amperes ....Class II Construction Hz ..... hertz .../min....revolutions or reciprocation per minute ....alternating current...
  • Page 7: Functional Description

    FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Shaft lock 005802 CAUTION: • Never actuate the shaft lock when the spindle is moving. The tool may be damaged. Press the shaft lock to prevent spindle rotation when install- ing or removing accessories.
  • Page 8 Screw the side grip securely on the position of the tool as shown in the figure. Installing or removing wheel guard 005805 9553NB CAUTION: • When using a depressed center grinding wheel/Multi- disc, flex wheel, wire wheel brush or cut-off wheel, the wheel guard must be fitted on the tool so that the closed side of the guard always points toward the operator.
  • Page 9: Installing/Removing Flex Wheel/Abrasive Disc

    Installing or removing depressed center grinding 001070 wheel/Multi-disc WARNING: • Always use supplied guard when depressed center grinding wheel/Multi-disc is on tool. Wheel can shatter during use and guard helps to reduce chances of personal injury. 1. Lock nut Mount the inner flange onto the spindle. Fit the wheel/disc on 2.
  • Page 10: Operation

    spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise. To remove the disc, follow the installation procedure in reverse. OPERATION WARNING: • It should never be necessary to force the tool. The weight of the tool applies adequate pressure. Forcing and excessive pressure could cause dangerous wheel breakage.
  • Page 11 Operation with wire cup brush 005834 (optional accessory) CAUTION: • Check operation of brush by running tool with no load, insuring that no one is in front of or in line with brush. • Do not use brush that is damaged, or which is out of balance.
  • Page 12: Maintenance

    A cut-off wheel can also be used with an optional guard. If you decide to use your Makita grinder with approved accessories which you purchase from your Makita distributor or factory service center, be...
  • Page 13 Your failure to do so could result in personal injury to you and others. If you need any assistance for more details regarding these accessories, ask your local Makita service center. 005836 C00166 9553NB...
  • Page 14 Memo...
  • Page 15 Memo...
  • Page 16 Memo...
  • Page 17 Stamp Timbre Makita Canada Inc. 1950 Forbes Street, Whitby, Ontario L1N 7B7 Fold...
  • Page 18 Your answers to the following questions are appreciated. 1. This product was purchased from? 3. How did you first learn of Makita Power Tools? Hardware/lumber Store Industrial Supply Magazine/Newspaper Catalog Tool Distributor Other ( From dealer Other ( Store display 2.
  • Page 19 When you need service... DATE • Explain the problem in a letter PURCHASED: • Enclose the letter with the tool DEALER’S NAME • Package carefully and send prepaid & ADDRESS: to the nearest Makita factory or authorized service centre MODEL NO.: SERIAL NO.:...
  • Page 20: Warranty Policy

    WARRANTY. “The Makita Warranty is the only and the entire written warranty given by Makita for the Makita tools. No dealer or his agent or employee is authorized to extend or enlarge upon this warranty by any verbal or written statement or advertisement.”...

This manual is also suitable for:

9554nb9555nb

Table of Contents