Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Advantech IDK2121WNK2FHA2EES
- Page 1 User Manual IDK2121WNK2FHA2E- TFT-LCD 21.5” FHD (LED Backlight)
- Page 2 No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. How- ever, Advantech Co., Ltd.
- Page 3 Whether your new Advantech equipment is destined for the labo- ratory or the factory floor, you can be assured that your product will provide the reliability and ease of operation for which the name Advantech has come to be known.
- Page 4 Because of Advantech’s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defec- tive, it will be repaired or replaced at no charge during the warranty period. For out- of-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight.
-
Page 5: Table Of Contents
Contents Chapter Overview..........1 General Description .................. 2 Display Characteristics................2 Table 1.1: Display Characteristics ..........2 Optical Characteristics ................3 Table 1.2: Display Characteristics ..........3 Functional Block Diagram ................. 5 Figure 1.1 Function block diagram ..........5 Absolute Maximum Ratings ..............5 1.5.1 Absolute Ratings of TFT LCD Module .......... - Page 6 Touch Screen..................26 5.1.1 Touch Characteristics ..............26 5.1.2 Optical Characteristics..............26 5.1.3 Environment Characteristics............26 5.1.4 Mechanical Characteristics............26 5.1.5 Electronic Characteristics ............26 5.1.6 General specification ..............27 Touch controller ..................27 5.2.1 Touch Controller Characteristics ..........27 5.2.2 Pin Assignment and Description..........
-
Page 7: Chapter 1 Overview
Chapter Overview... -
Page 8: General Description
General Description IDK-2121W series is a Color Active Matrix Liquid Crystal Display composed of a TFT- LCD panel, a driver circuit, and backlight system. The screen format is intended to support the FHD (1920(H) x 1080(V)) screen and 16.7M colors (RGB 8-bits data). All input signals are dual LVDS interface. -
Page 9: Optical Characteristics
Optical Characteristics Table 1.2: Display Characteristics Item Unit Conditions Min. Typ. Max. Note Horizontal(Right) CR = 10 (Left) Viewing Angle [degree] Vertical (Up) CR = 10 (Down) Contrast ratio Normal Direction 3500 Raising Time (TrR) Response Time [msec] Falling Time (TrF) Raising + Falling Red x 0.589... - Page 10 Note 2: 9 points position 90 % 50 % 10 % 10 % 50 % 90 % Note 3: The luminance uniformity of 9 points is defined by dividing the maximum luminance values by the minimum test point luminance Minimum Brightness of nine points Maximum Brightness of nine points Note 4: Measurement method The LCD module should be stabilized at given temperature for 30 minutes to avoid...
-
Page 11: Functional Block Diagram
Functional Block Diagram The following diagram shows the functional block of the 21.5 inches Color TFT-LCD Module: Figure 1.1 Function block diagram Absolute Maximum Ratings Absolute maximum ratings of the module is as following: 1.5.1 Absolute Ratings of TFT LCD Module Item Symbol Min. -
Page 12: Outline Dimension
Note 2: Permanent damage to the device may occur if exceeding maximum values Note 3: For quality performance, please refer to AUO IIS (Incoming Inspection Stan- dard). 1. 90% RH Max ( Ta ≤ 39 °C 2. Max wet-bulb temperature at 39 or less. - Page 13 Rear View IDK-2121W User Manual...
-
Page 14: Idk-2121Wn-1Kfha1E
1.6.2 IDK-2121WN-1KFHA1E Front View IDK-2121W User Manual... - Page 15 Rear View IDK-2121W User Manual...
- Page 16 IDK-2121W User Manual...
-
Page 17: Chapter 2 Electrical Characteristics
Chapter Electrical Characteristics... -
Page 18: Power Specification
Power Specification Input power specifications are as follows: Table 2.1: Power specification Symbol Parameter Min. Typ. Max. Unit Condition ± Logic/LCD Drive [Volt] Voltage VDD= 5.0V,All white pattern, At 60Hz Input Current 0.81 0.89 VDD= 5.0V, All white pattern At 75Hz [Watt] VDD= 5.0V,All white pattern, At 60Hz... -
Page 19: Signal Electrical Characteristics
2.1.1 Signal Electrical Characteristics Input signals shall be low or Hi-Z state when VDD is off. Table 2.2: Signal electrical characteristics Symbol Parameter Min. Typ. Max. Unit Condition Differential Input High Threshold +100 [mV] VCM = 1.2V, Note 1 Differential Input Low Threshold -100 [mV] VCM = 1.2V... - Page 20 IDK-2121W User Manual...
-
Page 21: Chapter 3 Signal Characteristics
Chapter Signal Characteristics... -
Page 22: Pixel Format Image
Pixel Format Image Following figure shows the relationship between input signal and LCD pixel format. Pin Description The module using a pair of LVDS receiver SN75LVDS82 (Texas Instruments) or com- patible. LVDS is a differential signal technology for LCD interface and high speed data transfer device. - Page 23 Table 3.1: Pin Description RxE1- Negative LVDS differential data input (Even data) RxE1+ Positive LVDS differential data input (Even data) Power Ground RxE2- Negative LVDS differential data input (Even data) RxE2+ Positive LVDS differential data input (Even data) RxEC- Negative LVDS differential clock input (Even clock) RxEC+ Positive LVDS differential clock input (Even clock) RxE3-...
-
Page 24: The Input Data Format
The Input Data Format Note1: Normally DE mode only. VS and HS on EVEN channel are not used. Note2: Please follow VESA. Note3: 8-bit in IDK-2121W User Manual... -
Page 25: Interface Timing
Interface Timing 3.4.1 Timing Characteristics Signal Name Item Symbol Min. Typ. Max. Unit Clock Frequency 1/ TClock Frame Rate Frequency 1/Tv Period 1088 1120 2047 Vertical Active 1080 1080 1080 T_line Section Blanking Period 1034 1060 2047 Horizontal Active T_clock Section Blanking 1087... -
Page 26: Power On/Off Sequence
Power ON/OFF Sequence VDD power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals from any system shall be Hi-Z state or low level when VDD is off. Power Sequence Timing Value Parameter Unit Min. -
Page 27: Chapter 4 Connector & Pin Assignment
Chapter Connector & Pin Assignment... -
Page 28: Tft Lcd Module
TFT LCD Module The physical connector interface is described below. These connectors are capable of accommodating the following signals and components. 4.1.1 Connector Table 4.1: Connector Connector Name / Description Interface Connector / Interface card Manufacture JAE or compatible Type Part Number JAE (FI-XB30SRL-HF11) or equivalent Mating Housing Part Number FI-X30HL (JAE) or compatible... -
Page 29: Led Driver Board
4.2.1.1 LED input connector pin define (CN1): Pin No. Pin Definition Vin(+12V) Vin(+12V) ON/OFF(0V: Off ; +5V: On) Dimming (PWM) 4.2.1.2 LED output connector pin define (CN2,CN3): Pin No. Pin Definition VLED- VLED+ 4.2.2 LED Driver Board 4.2.2.1 Specification: Table 4.3: Specification Symbol Characteristics Condition... -
Page 30: Figure 4.1 Dimension
Note1: When the input ≤ 1KHz, the high-level digital output must be greater than the total output level of only 5%. 4.2.2.2 LED driver board dimension Figure 4.1 Dimension IDK-2121W User Manual... -
Page 31: Chapter 5 Touch Screen & Touch Controller
Chapter Touch Screen & Touch Controller... -
Page 32: Touch Screen
Touch Screen 5.1.1 Touch Characteristics The touch panel is a resistance type used with flat LCD displays. Touches via finger or stylus send coordinate points to the PC from voltage changes at the contact point. 5.1.2 Optical Characteristics Item Specification Remarks 80% ±... -
Page 33: General Specification
Tail length 205.00±6.00 mm Touch controller Advantech ETM-RES04C Touch Control Board, is the ultimate combo board. This touch panel controller provides optimum performance of your analog resistive touch panels for 5-wire models. It communicates with the PC system directly through USB and RS-232 connectors. -
Page 34: Pin Assignment And Description
Touch resistance under 3K ohm Serial Interface EIA 232E (Serial RS-232) No parity, 8 data bits, 1 stop bit, 9600 baud (N, 8, 1, 9600) Supports Windows 2000/ Vista/ XP/ 7, Windows CE 5.0/ 6.0/ 7.0, Windows NT4, Linux, DOS, QNX USB Interface ... -
Page 35: Figure 5.1 Board Mounted Header
5.2.2.2 Combo Interface Connector, JP1, Pins and signal descriptions The combo interface connector, USB and RS-232, is a box 2.0mm 10-pins 90 degree, Male type with lock connector, intended to be used with single wired pins in 5+5 pins header. The pins are numbered as shown in the table below. Signal Signal Function RS-232... -
Page 36: Physical Dimension
5.2.3 Physical dimension ETM-RES04C-EEH4EE Touch Control Board (Unit: mm) IDK-2121W User Manual... -
Page 37: Handling Precautions
Appendix Handling Precautions... -
Page 38: Optical Characterisctics
Optical Characteristics The optical characteristics are measured under stable conditions at 25°C (Room Temperature) Since the front polarizer is easily damaged, pay attention not to scratch it. Be sure to turn off the power supply when inserting or disconnecting from the input connector. - Page 39 No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permis- sion of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2013...