Subscribe to Our Youtube Channel
Summary of Contents for Interlogix NX-592E
- Page 1 NX-592E-GSM Wireless Gateway Installation Manual P/N 466-2204 • REV F • January 2011...
- Page 2 Copyright Copyright © 2011 Interlogix, a UTC Fire & Security Company. All rights reserved. This document may not be copied in whole or in part or otherwise reproduced without prior written consent from UTC Fire & Security except where specifically permitted under US and international copyright law.
-
Page 3: Table Of Contents
Status LEDs .................. 14 Specifications................15 Troubleshooting................17 Contacting us ..............17 Online resources ................17 Creating a new subscriber account........... 19 Customer information..............20 System operation from Alarm.com ..........20 FCC notice ..................20 NX-592E-GSM Wireless Gateway Installation Manual... -
Page 5: Preface
Preface This is the . This document NX-592E-GSM Wireless Gateway Installation Manual includes an overview of the product and detailed instructions explaining: • how to install the unit; and • how to program the unit. There is also information describing how to contact technical support if you have questions or concerns. - Page 6 WARNING: Warning identify conditions or practices that could result in equipment damage or serious personal injury. NX-592E-GSM Wireless Gateway Installation Manual...
-
Page 7: Product Summary
Product summary The NX-592E-GSM Wireless Gateway (Figure 1 below) allows NetworX owners to control and monitor their system status from the Alarm.com website. Through a wireless, two-way paging network, your customer has limited controls on such features as security, notifications, history, and authentication (see “System operation from Alarm.com”... - Page 8 Indicates data bus activity between panel and module Status LED Indicate communications status with two-way pager network (see “Status LEDs” on page 14) Wiring terminals Panel wiring connections (see “Wiring connections” on page 11) Antenna jack Antenna connection for wireless data transceiver NX-592E-GSM Wireless Gateway Installation Manual...
-
Page 9: Before Installation
Modem Serial # dialog box, enter the 10-character ID found on the gateway you purchased. If you are unable to proceed with the modem serial number, contact Alarm.com. 10. Select NX in the list box Panel Type NX-592E-GSM Wireless Gateway Installation Manual... -
Page 10: Programming The Number Of Zones
To program the number of zones into the gateway, do the following: 1. Once the account is created, log on to the Alarm.com Dealer website at: https://www.alarm.com/dealer 2. Click the Customers tab, and then click the Customer Support subtab. NX-592E-GSM Wireless Gateway Installation Manual... -
Page 11: Installation
• Do not exceed the panel’s total output power when using panel power for bus devices and hardwired sensors (refer to your panel documentation). Tools and supplies needed • Slotted and Phillips screwdrivers NX-592E-GSM Wireless Gateway Installation Manual... -
Page 12: Mounting Locations
Wear a grounding strap or touch a bare grounded metal surface to discharge static electricity. Figure 3: Removing the enclosure Press here 2. Fasten the antenna to the antenna jack (see Figure 2 on page 6). NX-592E-GSM Wireless Gateway Installation Manual... -
Page 13: Wiring Connections
Table 3: Terminal descriptions Terminal Description Connect to the KP POS terminal of the NetworX panel Connect to the KP COM terminal of the NetworX panel DATA Connect to the KP DATA terminal of the NetworX panel NX-592E-GSM Wireless Gateway Installation Manual... -
Page 14: Case Tamper Switch Installation
When you exit Program Mode, the control panel automatically enrolls the devices. This process takes about 12 seconds. During this time, the Service LED will illuminate and User codes will not be accepted. NX-592E-GSM Wireless Gateway Installation Manual... -
Page 15: Programming Using The Keypad
2. Enter the “Go to program” code (the default code is 9, 7, 1, 3). If the code is valid, the keypad display will prompt you for a device address. 3. Enter the address of the NX-592E (7, 8) then press #. At this point, the keypad display will prompt you for a programming location to be entered. -
Page 16: Status Leds
Red REG LED The bottom red REG LED indicates the module is registered and in range. When the module is registered and in range. When the module is out of range and not registered with the network. NX-592E-GSM Wireless Gateway Installation Manual... -
Page 17: Specifications
Flashes Module in range, first message sent, currently sending message. Specifications Compatibility NetworX panels Power requirements 9.5 to 15 VDC, 12 V nominal, 65 mA (continuous), 1600 mA (instantaneous peak), maximum from panel or auxiliary power supply NX-592E-GSM Wireless Gateway Installation Manual... - Page 18 Humidity 90% relative humidity, noncondensing Case color Belgian gray Case materials High impact, ABS plastic Dimensions (H x W x 5.25 x 4.125 x 1.0 in. (13.3 x 10.5 x 2.5 cm) Installation Wall mount NX-592E-GSM Wireless Gateway Installation Manual...
-
Page 19: Troubleshooting
PDFs. To read these documents, you will need Adobe Reader, which you can download free from Adobe’s website at www.adobe.com Training To view any available online training for UTC Fire & Security products, select the Training link. (Online training is not available for all products.) NX-592E-GSM Wireless Gateway Installation Manual... - Page 20 Customer service and technical support From the Customer Support menu, select Customer Service or Technical & Application. Select the appropriate product category for the contact information or use the menu to select a location outside the US. NX-592E-GSM Wireless Gateway Installation Manual...
-
Page 21: Creating A New Subscriber Account
Leave “Customer information” on page 20 from this document with your customer. The information on these pages describes security system use and limitations of the Alarm.com website. This information does not appear in any owner’s manual or user guide. NX-592E-GSM Wireless Gateway Installation Manual... -
Page 22: Customer Information
Changes or modifications not expressly approved by UTC Fire & Security can void the user’s authority to operate the equipment. The wireless modem used with this product is an intentional radiator. Refer to labeling on the modem for the FCC ID. NX-592E-GSM Wireless Gateway Installation Manual...
Need help?
Do you have a question about the NX-592E and is the answer not in the manual?
Questions and answers