Checking before Operation Start OSD Menu Preset Group OSD Display of Main Screen ○ OSD Menu General Rules of Key Operation for Menu Main Menu Display Setup Preset Setup Group Setup Alarm Setup ○ Specification 2/21 Mini Pan/Tilt Dome Camera Instruction Manual...
Compact size and Easy installation The size of the dome is as small as ∅104 × 110(H) mm. There are two mounting choices. Direct ceiling mount with mounting plate. Wall mount with wall mount bracket. 3/21 Mini Pan/Tilt Dome Camera Instruction Manual...
INTRODUCTION Product & Accessories Product & Accessories Dome Camera Mount Plate Terminal Blocks Screws Options Wall mount bracket Alarm I/O module 4/21 Mini Pan/Tilt Dome Camera Instruction Manual...
Also, camera always regard this home position as zero angle and move pan motion from - 172.5° to +172.5°. Home Position 172.5 172.5 5/21 Mini Pan/Tilt Dome Camera Instruction Manual...
By pushing and twisting the gray ring, assemble ○ ○ mounting plate, fix the camera to the mounting the clear dome cover. Care must be taken not to plate. make fingerprint on to the clear dome. 6/21 Mini Pan/Tilt Dome Camera Instruction Manual...
Then, tighten screw completely. Make cable to pass through the center hole of By pushing and twisting the camera into the ○ ○ bracket. mounting plate, fix the camera to the wall mount. 7/21 Mini Pan/Tilt Dome Camera Instruction Manual...
Assemble the top cover of wall mount bracket with By pushing and twisting the gray ring, assemble ○ ○ screws included. the clear dome cover. Care must be taken not to make fingerprint on to the clear dome. 8/21 Mini Pan/Tilt Dome Camera Instruction Manual...
When you want to operate the camera with a controller. The Camera ID in this DIP switch setting must be identical to the camera ID of the controller. If you have multiple cameras, it is recommended to memorize the Camera IDs and their camera locations. 9/21 Mini Pan/Tilt Dome Camera Instruction Manual...
Page 10
Otherwise, the camera will be out of control. If you changed camera protocol by changing DIP S/W, the change will be effective after you reboot the camera. 10/21 Mini Pan/Tilt Dome Camera Instruction Manual...
‘ON’ state. The last camera may be decided by longest cable length. Do not turn on the terminal resistor of all cameras. Controller Terminal Resistor ON RS-485 Terminal Resistor Terminal Resistor Terminal Resistor 11/21 Mini Pan/Tilt Dome Camera Instruction Manual...
The D+, D- lines should be connected ‘+’, ‘-‘ pins respectively. Alarm I/O Use this connecter if you have Alarm I/O module. If you need detail information, please refer User’s manual of Alarm I/O module. 12/21 Mini Pan/Tilt Dome Camera Instruction Manual...
Since the operation method can be different for each controller available, refer to the manual for your controller if camera can not be controlled properly. Major operations of this manual are based on the standard Pelco® Controller. 13/21 Mini Pan/Tilt Dome Camera Instruction Manual...
<Using controller without Pattern key> After type 80+Group No. (i.e. 81~84), press Preset key in the controller. [81~84] + [Preset] Ex) If group number is 3, press 83 + Preset Delete Group Use OSD Menu. 14/21 Mini Pan/Tilt Dome Camera Instruction Manual...
If the I/O is OFF state, '-' will be displayed. Ex) Point 1 and 7 of Alarm inputs are ON state and 2 and 4 of output are ON. OSD will be show as below. O:-2-4 I:1-----7- 15/21 Mini Pan/Tilt Dome Camera Instruction Manual...
P/T INFORMATION ALARM INFORMATION Camera ID [ON/OFF] DISPLAY FACTORY RESET ------------------------------ Action Title [ON/OFF] P/T Information [ON/AUTO/OFF] Alarm Info. [ON/OFF] If you activate Display Factory Reset, all options will return to ON state. 16/21 Mini Pan/Tilt Dome Camera Instruction Manual...
By tilting joystick Up/Down, the value can be toggled the '-' sign or a number representing its digit. ③ Also, by tilting joystick Left/Right, you can move to next digit. ④ After you have changed values, press Near key to save it or press FAR key to cancel it. 17/21 Mini Pan/Tilt Dome Camera Instruction Manual...
② After changing the value desired using joystick, press the Near GROUP NUMBER : 1 P32 x0 key to save. If you press the Far key corresponding changes will be canceled. Up/Down GROUP NUMBER : 1 P32 x0 18/21 Mini Pan/Tilt Dome Camera Instruction Manual...
1 whenever Alarm 1 ALARM7 ACTION : NOT USED ALARM8 ACTION : NOT USED is activated. Also, camera will move to preset 2 ------------------------------ whenever Alarm 2 is activated. 19/21 Mini Pan/Tilt Dome Camera Instruction Manual...
DC 12V / 1A (With Alarm I/O) 110∅ × 110(H) mm Size Weight Approx. 450g Operating Temperature 0°C ~ 40°C * Specifications of this product are subjected to change without notice. Accessory Wall mount bracket 37.5 20/21 Mini Pan/Tilt Dome Camera Instruction Manual...