B.David 9333 Instructions And Operating Manual

(Page 1 )
B. David Company
Nano Filtration System
Instructions and Operating Manual
Model # 9333
Important – set flow meter to 1000 gallons

Specifications

Pressure Range: 2.1--8.62 bar (20-115 psi)
Temperature Range: 4.4-38.8°C (4G-102°F)
Service Flow Rate
@60 psi (4.1 bar):
2.3 Lpm at
Rated Service Life:
3,785 L (1000 gallons)
Dimensions: 394 mm
(15.5 in.
Weight (filled with water): 8.6 kg (19 lbs.)
Parts Included
•Filter system with filter cartridges
•Installation hardware (mounting screws, saddle valve, fittings)
• 6.35 mm (1/4-inch) tubing
• Lead-free faucet
Tools and Materials
Required:
• Safety Glasses
•Hand electric drill
or
(cordless recommended)
•File
• Phillips head screwdriver
•2 Adjustable wrenches
•Tube cutters or util i t y knife
Precautions
WAR NING
L P rotect filters against freezing, which can cause
cracking of the filter and water leakage.
The rubber o-ring provides the water-tight seal between
the cap and the bottom of the housing. It is important that
the o-ring
be properly seated in the groove below
housing or a water leak could
To prevent costly repairs or possible
sump of plastic housings must be replaced every five years
for clear, and ten years for opaque. I f sump i s older than
recommended, replace immediately. Date
reference and indicate replacement
NOTE:
For cold water use only.
•
Make certain that installation compl i e s
•
laws and regulations.
4.1 bar 0.6 gpm
x 133 mm x 356 mm
x 5.25 in. x 14 in.)
I i i i f sink does not have hole
for separate faucet:
• Center punch
• 19 mm (3/4-inch) drill bit
the threads of the
occur.
water damage, the
sump for
date.
with all local
RS-90
• After prolonged periods of non-use (such as during a vacation) i t
is recommended that the system be flushed thoroughly. Let
water run for 5-6 minutes before using.
• The filter cartridges
l i f e. Changes in taste, odor, and/or flow of the water being filtered
indicate that the cartridges should be replaced.
I Installation
• For standard under-sink installation on 10 mm (3/8-inchl cold
water line.
• Please read all instructions and precautions before installing and
using your filtration System.
• Numbered diagrams correspond
1. Installing the Saddle Valve
Diagram on page 2
Use of a hand drill is recommended. To protect
yourself from serious injury or fatal shock when using an electric drill,
be sure the drill and the
grounded. When using a drill, follow the manufacturer's guidelines
and procedures.
NOTE: Saddle valve must be installed on a 51 mm (2-inch) long,
walled section of 10-22 mm (3/8-inch to 7/8-inch)
PVC pipe.
(A) Turn off cold water supply and (turn on nearest
starting installation. Place
line to catch excess
(C) Drill a 3 mm (1/8-inch) hole in cold water
burrs with sandpaper or
(D) Turn handle on the saddle
mm (3/16-inch) beyond black rubber gasket.
(E) Place valve body over hole in cold
hole.
(F) Attach back plate of clamp and tighten bolts evenly and firmly so
brackets are parallel.
(G) Turn valve handle clockwise to closed position and leave closed
until installation is complete.
2. Selecting the Faucet Location
Diagram on page 2
NOTE: The drinking water faucet should be positioned with function,
convenience, and appearance i n mind. An adequate flat area is
required to allow faucet
through a 19mm (3/4-inch) hole.
38mm
(1-inch) diameter holes that may be used for faucet installation of
these pre-drilled holes cannot be used or
location, i t will be necessary to drill a 19mm (3/4-inch) hole in the
sink to accommodate the
RC-93
-Filter placement above-
(B. David Specific filters)
used with this system have a limited service
with numbered steps.
outlet i t is plugged into are properly
steel, brass, copper, or
faucet
a tray or towels under the
water.
line. Remove any
file.
valve to expose lance no more than 5
water l i ne so lance fits
base to rest securely. The faucet fits
Most sinks have pre-drilled 35 or
are in an inconvenient
faucet.
RP-100
straight-
before
cold water
into