Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for IEI Technology PPC-5022
- Page 1 PPC-5022 12.1” TFT Panel PC User Manual (Version1.0) May 21, 2003...
- Page 2 All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer. Trademarks PPC-5022 is a registered trademark of ICP Electronics Inc. IBM PC is registered trademark International...
-
Page 3: Table Of Contents
Table of Contents Introduction ............. 3 Checklist..................3 Features ..................3 Specifications ................4 Dimensions ................6 System Setup........... 7 Assembly Diagram ..............7 POS-566/370 CPU Board Installation ......10 Power Supply Installation..........11 Disk Drive Installation ............12 Panel Mounting................4 Arm Mounting ................6 Rack Mounting .................7 Appendix A Power Supply......8 Appendix B Display Interface ..... -
Page 4: Introduction
1 Introduction The PPC-5022, a 12.1" high brightness LCD TFT Panel PC, takes advantage of the modern flat-panel display technology. It consists of a POS-566/370 CPU board, one hard drive bay and an integrated power supply to ensure minimum size. The PPC-5022 is an IBM... -
Page 5: Specifications
LCD Display The PPC-5022 is equipped with a high brightness 12.1" TFT LCD. Power Supply The PPC-5022 is equipped with a standard ACE-816APS 150W power supply with PFC. Touch Screen (optional) Aluminum front panel supports both resistive and capacitive touch screens. - Page 6 3M touch capacitive type touch screen (optional) Type: Analog Resistive Resolution: Continuous Light transmission: Typical value 88% Support Operating Systems: Supports DOS, Windows 3.1, 95, 98, NT/Me/2000, WinCE. NET. Please download the capacitive type driver from IEI web site. Environmental Specifications Operating Temperature: 0 ~ 50¢...
-
Page 7: Dimensions
Dimensions Front Panel: 340mm x 260mm x 9mm (WxHxD) Cabinet: 310mm x 230mm x 99mm (WxHxD) -
Page 8: System Setup
Assembly Diagram The Reverse Side of PPC-5022 The diagram below shows the reverse side of PPC-5022. For maintenance, installation or upgrade, please remove the back cover first by unfastening the 9 screws shown in the diagram. - Page 9 The Rear View of Cabinet being Upside Down The following figure shows the rear view of cabinet with the upside down. One HDD and one power supply are accessible for operation on the driver frame. POS-370 POS-566...
- Page 10 The Side View of PPC-5022 On the side panel, one fan and two speakers will be found. Please bear this in mind when mounting the unit.
-
Page 11: Pos-566/370 Cpu Board Installation
POS-566/370 CPU Board Installation Simply place the board into the cabinet and then fasten it by four screws. -
Page 12: Power Supply Installation
Power Supply Installation Step 1. Fasten the power supply to the bracket with two screws. Step 2. Slide and push the whole module of power supply into the cabinet as the figure shown below, and then fasten it with two screws. Input Voltage: 90V to 264VAC Output rating: Nominal... -
Page 13: Disk Drive Installation
Disk Drive Installation The following sections will guide you how to install the HDD. Step1. Unscrew and take out the five screws shown .below. Step2. Slide out the cabinet from the panel as the diagram shown below. - Page 14 HDD Installation Step1. Fasten the HDD to the HDD cage as the diagram shown below. Step2. Push the HDD cage into the HDD bracket and fix it by the key lock. NOTE: connect HDDs and CD-ROM as the manner shown below MASTER SLAVER IDE1...
- Page 15 FDD and CD-ROM Installation Step 1. Slide FDD into the bottom of disk bay and fasten it with four screws on both sides. Step 2. With two screws, attach the slime type floppy adapter board to the back of disk bay. Step 3.
- Page 16 Step 5. Put the whole set of FDD and CD-ROM into chassis and fasten it with five screws as the following figure shown.
- Page 17 Speakers and Fan Installation Step1. Place the speakers and the fan into the positions as the diagram shown below. Step2. Fasten them with six screws.
-
Page 18: Panel Mounting
Panel Mounting PPC-5022 is designed for panel mounting. Step1. Check the cut out dimension first. Step2. Mount it into the panel by four supporters. Please refer to the diagrams below. 312.0 UNIT:mm... - Page 19 Step1. Drill holes on the place for wall mounting according to the holder shown below. 153.00 90.00 4-D4.5 Step2. Fasten the two holders to the PPC-5022 with the screws as the diagram shown here. Step3. Hang the whole machine onto the wall.
-
Page 20: Arm Mounting
Arm Mounting PPC-5022 is not only suitable for panel and wall mounting but also ideal for arm mounting with a 75/100 mm interface pad; and the specification conform to proposed VESA standards. -
Page 21: Rack Mounting
DM/SRM/PPC serial product provides optional rack mount kit for industrial racks. The following diagram shows how to mount DM/SRM serial product onto the 19" Rack. Step1 & 2. Fasten the rack-mount-kit onto PPC-5022. Step3 & 4. Fasten the whole machine onto the rack as shown below. -
Page 22: Appendix A Power Supply
Appendix A Power Supply Industrial Power Supply: ACE-816APS series Power Supply High reliability triple output switching power supply (just 40.6mm in height) Standard power supply: ACE-816APS Efficiency: 68% min Protection: Over Voltage/Load protection and short circuit protection Operating temperature: 0°C to 50°C Vibration: 5~17Hz, 0.1”... -
Page 23: Appendix B Display Interface
Appendix B Display Interface A-1: For POS-566 Power on/off switch LCD on/off switch RESET switch B-2: For POS-370 Power on/off switch RESET switch LCD on/off switch... -
Page 24: Appendix C Touch Panel Controller
Appendix C Touch Panel Controller The optional touch screen provides RS232 interface, and the wire diagram of the controller is shown below.