Download
Share
Print this page
  1. Manuals
  2. Brands
  3. BETCO Manuals
  4. Garage Door Opener
  5. DOOR SYSTEMS
  6. Installation instructions & owner's manual

BETCO DOOR SYSTEMS Installation Instructions & Owner's Manual

Hide thumbs
1
2
3
4
5
6
7
8
9

Advertisement

Quick Links

Download this manual
WARNING
THE FOLLOWING INSTRUCTIONS ARE A GUIDE
FOR PROFESSIONAL DOOR INSTALLERS,
SERIOUS INJURY MAY RESULT IF
INEXPERIENCED PERSONNEL
ATTEMPT TO WORK ON THIS PRODUCT
1.
Read entire instructions carefully before
installing door.
2.
Installation, adjustments and repairs must be
performed by an experienced, trained professional
door installer.
3.
Use proper lifting equipment and lifting procedures
when installing door in opening.
4.
Do not cut retention band around door roll or unwrap
protective wrapper until instructions indicate.
5.
Do not stand in door opening during
operation of door.
6.
Do not allow anyone other than authorized
installers to adjust or install.
7.
If door becomes inoperative or hard to
operate, contact a qualified door agency.
ITEM
DESCRIPTION
A
DOOR CURTAIN
B
DOOR TRACK, LEFT
DOOR TRACK, RIGHT
C
DOOR AXLE ASSEMBLY
D
DOOR LATCH BASE
DOOR LATCH SLIDE
E
DOOR EXTRUSION ASSEMBLY
F
DOOR STIFFENER CHANNEL
G
DOOR ASTRAGAL
H
DOOR BRACKET, LEFT
DOOR BRACKET, RIGHT
I
DOOR BRACKET ASSEMBLY
J
DOOR STOP
K
DOOR HANDLE
L
TENSION ADJUSTER
M
FELT SEPARATOR STRIP
N
HARDWARE PACKAGE
O
HARDWARE PACKAGE
P
DOOR CURTAIN DAMPENER
BETCO DOOR SYSTEMS
INSTALLATION INSTRUCTION & OWNERS MANUAL
SAFETY TIPS
DP6-WITH HEIGHT COLOR
DTA-HEIGHT-DL
DTA-HEIGHT-DR
DB-WIDTH-2D OR 3D
D20006
D20007
DX-WIDTH-AL
DS-WIDTH-GL
D20008
D20005
D20004
D20002
D20009
D20017 W/BEARING
D20018 W/O/BEARING
D20028
STEEL CONSTRUCTION
WOOD OR MASONRY CENTER
D20028
I
H
J
D
WARNING LABEL
B
A
BETCO LABEL
(OUTSIDE DOOR)
PART NO.
ORDER BY OPENING WIDTH, HEIGHT & COLOR
ORDER BY DOOR OPENING HEIGHT
ORDER BY DOOR OPENING WIDTH
NONE
ORDER BY DOOR OPENING WIDTH
ORDER BY DOOR OPENING WIDTH
NONE
NONE
WITH DOOR BRACKET ADAPTER
NONE
NONE
OPTIONAL-ORDER W/BEARING OR
W/O/BEARING AT TIME OF ORIGINAL ORDER
NONE
ORDER BY BUILDING CONSTRUCTION
ORDER BY BUILDING CONSTRUCTION
NONE
M
E
F
G
K
NOTES
Page 1
12/31/03
c
C
P

Advertisement

loading
Need help?

Need help?

Do you have a question about the DOOR SYSTEMS and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for BETCO DOOR SYSTEMS

  • Page 1 BETCO DOOR SYSTEMS INSTALLATION INSTRUCTION & OWNERS MANUAL WARNING THE FOLLOWING INSTRUCTIONS ARE A GUIDE FOR PROFESSIONAL DOOR INSTALLERS, SERIOUS INJURY MAY RESULT IF INEXPERIENCED PERSONNEL ATTEMPT TO WORK ON THIS PRODUCT SAFETY TIPS Read entire instructions carefully before installing door.
  • Page 2 STEP 1. Check the door opening height and width and make sure it is correct with the size door ordered. Make sure jambs are plumb and floor is level. STEP 2. Do not cut bands or unwrap protective cover around door at this time. Instruc- tions to do so will come in Step 8.
  • Page 3 STEP 4. Slide DOOR BRACKET ASSEMBLY onto the end of the AXLE as shown in Figure 3. Slide AXLE WASHER in place over AXLE and install COTTER PIN into AXLE through hole provided to secure the assembly. (NOTE: Locate Extrusion as shown for STEP 5 to provide 2-1/2 turns of spring tension) DOOR DOOR TRACK...
  • Page 4 DOOR AXLE ASSEMBLY JAMB INTERIOR WALL FIGURE 5 STEP 6. WARNING Position bottom of DOOR • Lift the DOOR AXLE ASSEMBLY. Do not lift Door by TRACKS against the back of wall tracks. columns, lift the DOOR AXLE • Door is not designed for a 1 man liftup installation. ASSEMBLY to position against wall At least 2 persons are needed to lift and position columns (Figure 5).
  • Page 5 12 ga. “ZEE” INSTALL A 12 GA. “CEE” INSTALL A 12 GA. “ZEE” REINFORCEMENT PLATE OVER THE REINFORCEMENT PLATE OVER THE DOOR TRACK IF SPECIFIED ON BETCO DOOR TRACK IF SPECIFIED ON BETCO DOOR SCHEDULE. DOOR SCHEDULE. OPENING WIDTH 5/16” X 1 1/2”...
  • Page 6 NOTE: If DOOR is equipped with TENSION ADJUSTER skip Steps 8 & 9 at this time and go to Step 10. STEP 8. Pre-tension the door springs by rotating the entire DOOR AXLE ASSEMBLY two and a half (2-1/2) complete turns in the direction of the arrow shown in Figure 7. While holding the BOTTOM EXTRUSION of the door securely, cut the straps around the door.

  • Page 7: Adjusting Tension

    ADJUSTING TENSION WARNING SINCE SPRINGS ARE UNDER EXTREME TENSION, NEVER REMOVE SPRING FASTENERS. KEEP A SECURE HOLD ON THE DOOR AND BOTTOM BAR WHEN ANY TENSION ADJUSTMENTS ARE MADE OR WHEN DOOR STOPS ARE NOT SECURELY ATTACHED. THE DOOR ROLL WILL TRY TO UNROLL RAPIDLY FIGURE 8 AND CAN CAUSE SEVERE INJURY.
  • Page 8 STEP 10. INSTALLING OPTIONAL TENSION ADJUSTER Slide DOOR TRACK ASSEMBLY with DOOR BRACKET onto AXLE ASSEMBLY. (TENSION ADJUSTER is factory assembled with DOOR BRACKET.) Attach spring to TENSION ADJUSTER into the offset hole with a 5/16” x 3/4” bolt and washer. Slide large WASHERS onto AXLE.

  • Page 9: Step 12. Preventive Maintenance

    STEP 12. PREVENTIVE MAINTENANCE When doors are originally installed, door axles, springs and door tracks are lubricated to ensure smooth movement. Over time, these oils dry out and problems arise where rubber and plastic surfaces come in contact with metal doors and tracks. While units are vacant, we suggest doors be rolled down and springs and axles be lubricated with spray on lithium grease.