Related Manuals for Merloni WASHING MACHINE AND WASHER-DRIER
Summary of Contents for Merloni WASHING MACHINE AND WASHER-DRIER
- Page 1 Merloni Elettrodomestici Technical Fitting Manual WASHING MACHINE AND WASHER-DRIER Language Issue/Edition Page 99-11-03/01 1-14...
-
Page 2: Table Of Contents
Fitting the machine into the units PLUMBING IN Connecting to the water supply Connecting the drainage pipe CONNECTION TO THE MAINS CAUTIONS AND ADVICE All measurements are expressed in millimetres (mm). N.B. Technical Fitting Manual Language Issue/Edition Page WASHING MACHINE AND WASHER-DRIER 99-11-03/01 2-14... -
Page 3: Conformity Of Appliance
The housing space, as well as having the dimensions indicated in Fig. 1, must obviously allow the electric cable and the water supply and drainage pipes to pass. Technical Fitting Manual Language Issue/Edition Page WASHING MACHINE AND WASHER-DRIER 99-11-03/01 3-14... -
Page 4: Unpacking
Fig. 2. Fig. 2 Technical Fitting Manual Language Issue/Edition Page WASHING MACHINE AND WASHER-DRIER 99-11-03/01 4-14... -
Page 5: Levelling
Fig. 3 The angle of inclination measured on the worktop must not exceed 2 degrees. When fitting on carpeting, ensure that ventilation is not blocked at floor level. Technical Fitting Manual Language Issue/Edition Page WASHING MACHINE AND WASHER-DRIER 99-11-03/01 5-14... -
Page 6: Fitting The Front Panel And Inserting The Machine Into The Units
La to po D oo r si rt e C ot e po Tu r se Technical Fitting Manual Language Issue/Edition Page WASHING MACHINE AND WASHER-DRIER 99-11-03/01 6-14... -
Page 7: Fitting Accessories For Wooden Panel (Door)
Fitting accessories for wooden panel (door) The accessories provided to fit the wooden panel are shown in the following figures. Fig. 5 Fig. 6 N° 2 Hinge supports N° 2 Hinges Technical Fitting Manual Language Issue/Edition Page WASHING MACHINE AND WASHER-DRIER 99-11-03/01 7-14... - Page 8 Metric screws l = 15 mm “type C” to fasten the hinge supports to the unit n˚4 Metric screws l = 7 mm “type D” to fasten the hinges to the supports Technical Fitting Manual Language Issue/Edition Page WASHING MACHINE AND WASHER-DRIER 99-11-03/01 8-14...
-
Page 9: Fitting The Elements To The Front Of The Machine
Insert the prong of the hinge indicated by an arrow in Fig. 6 into the housing on the hinge support, press the panel towards the surface of the machine and fasten the two hinges using two screws of “type D”. Technical Fitting Manual Language Issue/Edition Page WASHING MACHINE AND WASHER-DRIER 99-11-03/01 9-14... -
Page 10: Fitting The Machine Into The Units
Fig. 12. Fig. 12 Using the screws “type F”, adjust the depth according to the position of the mopboard, and if necessary fix it to the guides. Technical Fitting Manual Language Issue/Edition Page WASHING MACHINE AND WASHER-DRIER 99-11-03/01 10-14... -
Page 11: Plumbing In
If this precaution is not taken, the water inlet may become clogged, damaging the machine. Connect the other end of the pipe to the machine at the water connector provided, top right hand side (Fig. 14). Fig. 13 Fig. 14 Technical Fitting Manual Language Issue/Edition Page WASHING MACHINE AND WASHER-DRIER 99-11-03/01 11-14... -
Page 12: Connecting The Drainage Pipe
In all cases, the free end of the pipe must measure between 40 and 100 mm and it must not be underwater. Fig. 15 Technical Fitting Manual Language Issue/Edition Page WASHING MACHINE AND WASHER-DRIER 99-11-03/01 12-14... -
Page 13: Connection To The Mains
2. To ensure that the machine operates correctly it must be properly levelled, so that its inclination does not exceed 2â on the top. To do this, turn the adjusting feet (Chapter 4). Technical Fitting Manual Language Issue/Edition Page WASHING MACHINE AND WASHER-DRIER 99-11-03/01 13-14... - Page 14 Merloni Elettrodomestici Merloni Elettrodomestici spa viale Aristide Merloni, 47 - 60044 Fabriano tel. 0732/6611 - telex 560196 - fax 0732/662954 www.Merloni.com Language Issue/Edition Page 99-11-03/01 14-14...