Download Print this page

Elecom MR-K009 User Manual page 2

Usb 2.0 multi type card reader

Advertisement

Reading from and writing to a memory card using a PC
1
Activate the PC
1
If the PC is started with this product connected, the product may not be recognized.
The power of PC is turned on.
If this problem occurs, remove and reconnect the product.
2
Connect to the PC
1
2
Pull out the USB connector
Connect the USB connecter to the PC
from the product.
USB port. The product will be auto-
matically recognised by the PC.
USB connector
USB connector
3
Insert a memory card
1
2
Inser t a memor y card in the
Windows
®
The inserted memory card can be accessed.
appropriate slot with the correct
orientation and alignment.
2
Refer to "How to insert memory cards
Macintosh
®
A drive icon appears on the
into the corresponding card slots" (on
desktop and you can access the
the front side) for details
memory card.
Only insert one media card at a time.
Media may not be recognised if multiple cards are inserted at the same time.
4
Remove the memory card
1
Open "My Computer" ("Computer" in
Windows
®
Windows 7 and Windows Vista).
1
Macintosh
Drag the drive icon to the Trash (Eject).
®
The Trash icon(
) becomes an Eject (
5
Disconnect the card reader from the PC
1
2
Click the
,
,
, or
Click the message that appears.
Windows
®
icon in the Taskbar or the
Notification Area.
* If the
icon is displayed in the
®
Notification Area in Windows
7,
click it and then click the USB
icon (
) that appears.
* If removing a memory card
®
using Windows
7, proceed to
step
.
• If using a USB device or PC card besides this product, both names will be dis-
played. In this case, click the message that appears for this product (indicating a
USB mass storage device or USB disc).
If a memory card is inserted into the memory card slot when using Windows
click "Eject Mass Storage Device".
Remove all memory cards from the card reader slots.
Macintosh
®
Always disconnect the card reader from the PC before turning off the PC.
3
The card reader is automatically recognised and
the connection procedure is complete.
When using Windows
, an "installation complete"
®
* Confirm the
notification will appear in the taskbar.
proper up/down
orientation of the
connector when
you connect it.
If an Auto Play dialog box appears, select
the action that you want Windows to perform.
* If the card is empty, it is opened directly
as a removable disk.
Do not remove a memory card while the PC is writing to or reading from it.
2
3
Right-click the removable disk that the
Remove the memor y
memory card was assigned to, and on the
card from the slot.
context menu that appears, click [Eject].
2
Check that the drive icon has disap-
peared and remove the memory card
from the slot.
) icon.
Do not disconnect the card reader while the PC is writing to or reading from it.
3
The "Safe to Remove Hardware" notifica-
tion is displayed.
®
Windows
7, Windows
Proceed to Step
®
Windows Vista
7, Windows
Click
, and proceed to Step
7,
®
4
Disconnect the card reader from the USB port.
When using this product with Windows
Windows
®
2000 Service Pack 4 or later is required to use this product. Perform
the following steps to confirm your version. If using Service Pack 3 or earlier, use
Windows Update to update it to the latest version of Windows
tion on performing the update, refer to your PC manual or consult the manufacturer
of your PC.
1. Right-click the My Computer icon on your desktop, and then click "Properties"
from the menu.
The system properties window is displayed.
2. Confirm your version of Windows
®
If the Windows
installed on your computer does not support USB 2.0
When performing step 2 of "2. Connect to the PC", the following taskbar message or
system notification will appear when you connect the USB connector to the PC USB port.
When using Windows
®
XP Service Pack 1 or earlier
"HI-SPEED USB Device Plugged into non-HI-SPEED USB Hub"
When using Windows Vista
®
or Windows
"This Device Can Perform Faster"
This message is to inform you that even though this product is a USB 2.0-com-
patible device, the port that it is connected to does not support USB 2.0. In this
case, this product will operate at USB 1.1 speed, not that of USB 2.0.
®
About Windows
drive letters
®
In Windows
, a single drive letter will be assigned to the 4 memory card slots (the
letter shown in parenthesis is an example that assumes that the last assigned
drive letter is E).
More than 1 memory card slot cannot be used at the same time.
®
In Windows
7, the drive icon will appear once a memory card is inserted
into a slot.
®
About Macintosh
drive icons
When using a Macintosh
®
, a different drive icon will appear depending on which
memory slot you insert a card into.
Slot
Drive icon
If the PC does not recognise the card reader
If the PC does not recognise the card reader, disconnect it from the PC and try connecting
it again.
®
XP
®
In Windows
7, even if this product is recognised, the drive will not be dis-
played until a memory card has been inserted.
®
2000
- 2 -
®
2000
®
2000. For informa-
®
2000.
®
XP Service Pack 2 or later
ELECOM CO., LTD.
1-1 Fushimi-machi 4-Chome Chuoku, Osaka Japan 541-8765
URL: http://www.elecom.co.jp/global/
overseas@elecom.co.jp
ELECOM Korea Co., Ltd.
5F Suam Bldg. 1358-17, Seocho2-dong, Seocho-gu, Seoul 137-862, Korea
TEL : 1588-9514
FAX : (02)3472-5533
URL : www.elecom.co.kr
ELECOM Singapore Pte. Ltd
or
or
33 UBI AVENUE 3 # 03-56. VERTEX SINGAPORE (408868)
TEL : (65)-6347-7747
FAX : (65)-6753-1791
ELECOM India Pvt. Ltd.
408-Deepali Building, 92- Nehru Place, New Delhi-110 019, India
TEL: 011-40574543
e-mail: support@elecom-india.com
URL: http://www.elecom-india.com/
This manual is copyright of ELECOM Co., Ltd.
• Unauthorised copying and/or reproducing of all or part of this manual is prohibited.
The specifications and appearance of this product may be changed without prior notice for
product improvement purposes.
ELECOM Co., Ltd. shall bear no responsibility for any and all affects resulting from the use
of this product regardless of the above reasons.
Export or service transaction permission under the Foreign Exchange and Foreign Trade
Control Law is required in order to export this product or parts of this product that constitute
strategic materials or services.
The SD logo, SDHC logo, SDXC logo, microSD logo, and microSDHC logo are trademarks of
SD-3C, LLC.
• Multimediacard is trademark of Infineon Technologies AG .
• Memory Stick, Memory Stick PRO, Memory Stick Duo, Memory Stick PRO Duo, and
Memory Stick Micro are trademarks of Sony Corporation.
Windows and the Windows logo are trademarks of the Microsoft group of companies.
• Mac and the Mac logo are trademarks of Apple Inc., registered in the United States and other
countries.
• Company names, product names, and other names in this manual are generally trademarks
or registered trademarks.
USB 2.0 Multi Type Card Reader
MR-K009 series
User's manual
1st edition, January 10, 2012
©2012 ELECOM Co., Ltd. All Rights Reserved.

Advertisement

loading
Need help?

Need help?

Do you have a question about the MR-K009 and is the answer not in the manual?

Subscribe to Our Youtube Channel