Advertisement
Quick Links
Operating & Service Manual
Airetool
®
90103-IM
05/25/2011
EIC Series
Tube Cutters
Complete Cutter
5/8" OD
3/4" OD
7/8" OD
1" OD
Model #
Order #
Model #
Order #
Model #
Order #
Model #
Order #
EIC-626-626
5515772
EIC-625-750
5515635
EIC-625-875
5523035
EIC-625-1000
5518583
For additional product information visit our website at http://www.apextoolgroup.com
Advertisement
Related Manuals for Airetool EIC-626-626
Summary of Contents for Airetool EIC-626-626
- Page 1 5/8" OD 3/4" OD 7/8" OD 1" OD Model # Order # Model # Order # Model # Order # Model # Order # EIC-626-626 5515772 EIC-625-750 5515635 EIC-625-875 5523035 EIC-625-1000 5518583 For additional product information visit our website at http://www.apextoolgroup.com...
-
Page 2: Eye And Face Protection
Safety Recommendations moving components can entangle and enwrap, and can For your safety and the safety of others, read and un- result in serious injuries. Never wear long hair, loose fitting derstand the safety recommendations and operating in- clothes, gloves, ties or jewelry when working with or near structions before operating this tool. - Page 3 OR TURNED SIDE TO SIDE. STRESSFUL POSTURES SHOULD BE AVOIDED AND This Airetool product is designed to operate on minimum CAN BE CONTROLLED THROUGH TOOL SELECTION 90 psig ( 6.2 bar ), maximum 125 psig ( 8.6 ) air pressure.
-
Page 4: Cutting The Tubes
See replacing the tool bits page 13. Proper depending on tube material. tool bit care is very important in operating your Airetool tube cutter. NOTE : Tool bits can be sharpened if removed F. Have a container of solvent for washing or flush... - Page 5 CUTTER BODY COMPLETE FOR MODEL “EIC” & “TIC” TUBE CUTTERS P A R T S L I S T I N G F O R M O D E L " E I C " & " T I C " T U B E C U T T E R B O D Y C O M P L E T E I T E M #...
- Page 6 PARTS LISTING FOR MODEL " EIC " & "TIC" TUBE CUTTER BODY COMPLETE ITEM # PART # DESCRIPTION QUAN. ITEM # PART # DESCRIPTION QUAN. M ODEL IC-875 ( 7/8" O.D. ) ( 5515581 ) M ODEL IC-1000 ( 1" O.D. ) ( 5515571 ) 2672500 TTC-36-12 PILOT 2676400...
- Page 7 LEVER HOUSING ASSEMBLY FOR MODELS “EIC” & “TIC” TUBE CUTTERS PARTS LISTING FOR MODEL TTC-21-A LEVER HOUSING ASSEMBLY 5514403 ITEM # PART # DESCRIPTION QUAN. ITEM # PART # DESCRIPTION QUAN. 2671300 TTC-21 LEV ER HOUSING 8000800 10-32 x 1/4" SOC SET SCREW 2670200 TTC-11 SLEEV E BEA RING 2670400...
- Page 8 AIRETOOL AIR DRIVEN MODEL “TIC” INTERNAL TUBE CUTTER NEW - MANDREL DRIVER - SAME ONE FITS ALL SIZE “EIC” ELECTRIC CUTTERS LEFT HAND THREAD MANDREL DRIVER # ETC-30 ( 3073240 ) PARTS NEEDED TO CONVERT TI NEW "IC" TYPE TUBE CUTTER SIZE 5/8"...
-
Page 9: Motor Lubrication
After careful inspection of parts for wear, they should be thoroughly cleaned. Reassemble in reverse order of disas- sembly. The Airetool Models #ELEC-1001-600 and ELEC-1201-350 Electric tube cutter motos r will , when given proper care , give satisfactory operation for a very long period of time . - Page 10 ELECTRIC TUBE CUTTER MOTOR MODEL ELEC-1001-600 ( 3070050 ) ( See parts List On Adjacent Page 13 ) Page - 10...
- Page 11 PARTS LISTING FOR MODEL ELEC-1001-600 ELECTRIC TUBE CUTTER MOTOR 3070050 ITEM # PART # DESCRIPTION QUAN. ITEM # PART # DESCRIPTION QUAN. 06-82-5316 PA N HD SCREW 22-64-3190 CORD SET 06-82-7270 PA N HD SCREW 28-28-0601 DIA PHRA GM 31-44-1651 RIGHT SIDE HA NDLE 02-50-2440 NEEDLE BEA RING 06-95-0075 TRUSS HD SCREW 32-75-1606 SPINDLE GEA R...
- Page 12 TOOL BIT REPLACEMENT INSTRUCTIONS FOR AIRETOOL TUBE CUTTER MODELS: EIC, PIC & TIC NOTE : THESE INSTRUCTIONS PERFORMED WITH ASSEMBLY “BB” ATTACHED TO THE LEVER HOUSING (MODELS EIC & TIC) OR SPRING HOUSING (MODEL PIC). 1. REMOVE ASSEMBLY “AA” BY TURNING THE CUTTER BODY COUNTERCLOCKWISE THEN TURN THE MANDREL TIP COUNTERCLOCKWISE.
- Page 13 POINTS FOR GOOD TUBE CUTTING 1. KEEP BITS COOL - This will extend the bits life. It possible, use a flushing system of air and some type of good cutting fluid. 2. DO NOT FORCE FEED - To much pressure of the tool bits can cause the bits to puncture thru the tube wall which may cause the bits to break.
- Page 14 RECOMMENDED CUTTING SPEEDS FOR AIRETOOL TUBE CUTTERS MODELS “EIC”, “PIC” & “ T I C ” T U B E TUBE MATERIAL 1/4" 3/8" 1/2" 5/8" 3/4" 7/8" 1" 1 1/4" 1 1/2" 2" 7500 5000 3800 3000 2500 2200...
- Page 16 Tel: +55 15 2383929 Tel: +36 96 66 1383 Tel: +52 (442) 211-3800 Fax: +55 15 2383260 Fax: +36 96 66 1135 Fax: +52 (442) 103-0443 Apex Tool Group, LLC Airetool 1000 Lufkin Road ® Apex, NC 27539 Phone: 919-387-0099 Fax: 919-387-2614 www.apextoolgroup.com...
Need help?
Do you have a question about the EIC-626-626 and is the answer not in the manual?
Questions and answers