Table of Contents
Advertisement
Quick Links
Installation & Operation Manual
Important Information ............................................2
Safety Information .................................................3
Component Identification ......................................3
Specifications ........................................................4
Electrical Requirements ........................................4
Document # 101522 0608 REV A ER 784
Installation .............................................................5
Operation ..............................................................8
Table Adjustments ............................................... 11
Maintenance ........................................................19
Limited Warranty .................................................19
Advertisement
Table of Contents
Summary of Contents for brewer AssistPRO
-
Page 1: Table Of Contents
Installation & Operation Manual Important Information ..........2 Installation .............5 Safety Information ..........3 Operation ..............8 Component Identification ........3 Table Adjustments ..........11 Specifications ............4 Maintenance ............19 Electrical Requirements ........4 Limited Warranty ..........19 Document # 101522 0608 REV A ER 784... -
Page 2: Important Information
AssistPRO the best prior to operating the table. Become familiar with all of procedure table for every office. -
Page 3: Safety Information
SafEty InfOrMatIOn Safety Information failure to follow instructions with this symbol The primary concern of The Brewer Company is that the could result in serious personal injury and/or damage equipment is operated and maintained with the safety of to the unit. -
Page 4: Specifications
SpECIfICatIOnS Power Cord............... Weight of Table .............550 lbs. Load Rating (maximum): .... Extends 70 in. (Minimum) from table. 18 AWG / 3 ..... conductor, SJT grey jacketed junior hard service Seat/Back .............450 lbs.....with hospital plug Legrest (Flat & Kneeling) ........450 lbs. Type of protection against electrical shock …….. -
Page 5: Installation
InStaLLatIOn Overview Perform the following sequence in order when setting up the table: Uncrating Leveling the Base Installing the Foot Control & Hand Pendant Uncrating NOTE: Inspect all boxes and contents for damage. Re- port any damage to the carrier immediately. DO nOt lift at these points! CaUtIOn to avoid damaging the table’s upholstery or paint-... - Page 6 InStaLLatIOn (COntInUED) Leveling the table A leveling screw pad (Figure 5) is located in six places under the table’s base. Adjust the six leveling pads to achieve a solid, level installation. Figure 5. Leveling Screw Pad (located under table) Installing the power Cord 1.
- Page 7 InStaLLatIOn (COntInUED) Installing the Hand pendant 1. Remove the hand pendant from the shipping bag receptacle 2. Insert the plug end of the cord into the hand pendant receptacle on the backrest shroud. See figure 8. 3. Make sure the tab on the cord plug is aligned with the groove in the receptacle and plug is fully seated 4.
-
Page 8: Operation
OpEratIOn General NOTE: For optimum table performance, allow the table to reach room temperature before operating. NOTE: The table is not designed for continuous opera- WarnInG tion. If the table is operated continuously causing the control to exceed its allowable operating temperature, the If the table malfunctions, immediately remove your hand or foot from the controls, unplug the power table will go into a reduced speed mode. - Page 9 OpEratIOn (COntInUED) program Stop program recall Mode program program recall #1 recall #3 tilt Back table tilt Back table Down program Down program Down Down recall #2 recall #4 Figure 10 Controls 1. See figure 10 for the pedal and button identifications on the foot control 2.
- Page 10 OpEratIOn (COntInUED) Back Up Leg Up Back Down Leg Down tiltUp table Up table Down tilt Down program recall #1 program recall #2 program recall #3 program recall #4 Figure 11 Document # 101522 0608 REV A ER 784...
- Page 11 taBLE aDjUStMEntS table Height (figure 12) The table top can be adjusted to any height between 19” to 40”. 1. To raise the table, depress and hold the Table/Up 2. To lower the table, depress and hold the Table/Down function until the desired height is achieved. function until the desired height is achieved.
- Page 12 taBLE aDjUStMEntS (COntInUED) Back positions (figure 13) The back can be adjusted to any angle between horizon- tal and 85°. 1. To adjust the back from a chair (upright) position to a horizontal position, depress and hold the Back/Down function until the desired angle is achieved. 2.
- Page 13 taBLE aDjUStMEntS (COntInUED) Legrest positions (figure 16) ed preventing the legrest from contacting the treatment pan tray. If the legrest is inoperable, check to ensure The legrest can be adjusted from a horizontal position to that the treatment pan tray is in its fully stowed position a vertical position.
- Page 14 taBLE aDjUStMEntS (COntInUED) 5. When the table is moving in the auto run mode, motion on the foot control will indicate if the “Auto-Run” mode of the table can be stopped by: is on or off. To set the program mode using the hand a.
- Page 15 taBLE aDjUStMEntS (COntInUED) Legrest Extension (figure 18) In the horizontal position, the legrest can be extended 5” CaUtIOn to increase the overall length of the table. to prevent damage to the unit, the legrest must be Lift up on the legrest and pull outward to extend the returned to the shortest position prior to lowering legrest.
- Page 16 taBLE aDjUStMEntS (COntInUED) paper roll (figure 20) To change a paper roll, insert the paper through the slot in the backrest shrouding and set the paper roll in the holder. paper Slot Figure 20. Paper Roll Document # 101522 0608 REV A ER 784...
- Page 17 taBLE aDjUStMEntS (COntInUED) Stirrups perating the tirrupS igure 1. To operate the stirrups, grasp end of stirrup and pull straight out of the table. Lift up slightly while sliding the stirrup out. NOTE: Do not apply any downward pressure when pull- ing stirrup from table or it may be difficult to move.
- Page 18 taBLE aDjUStMEntS (COntInUED) treatment pan (figure 24) NOTE: A safety switch prevents upward motion of the legrest when the treatment pan tray is extended. This pre- vents the legrest from contacting the treatment pan tray. If the legrest upward motion is inoperable, check to ensure that the treatment pan tray is in its fully stowed position (inward).
-
Page 19: Maintenance
The Brewer Company or any part thereof, (b) any actual or alleged failure or de- fect in products of The Brewer company or any part thereof, or (c ) any actual or alleged breach or non-performance by The Brewer Company of this limited warranty.