1. Precautions and Safety Notices 1.1 safety precautions This monitor is manufactured and tested on a ground principle that a user’s safety comes first. However, improper use or installation may cause damage to the monitor as well as the user. Carefully go over the following WARNINGS before installing and keep this guide handy.
Portuguese, Russian, Turkish, French, Czech, ViewSonic CD Wizard Hungarian, Simplified Chinese, Traditional Chinese. Greek, Dutch, Bulgarian, Croatian, Romanian, Serbian, Slovak, Slovenian ViewSonic Quick Start Guide One Page Perfect Suite CD Screen Protector Mylar Foot Protector plastic Base assembly Procedure Card...
Page 6
2.2 Interface description D-SUB connector pin assignment Pin Number Pin Function Red video input Green video input Blue video input No Connection Ground Red video ground Green video ground Blue video ground H/V sync ground No connection (SDA) Horizontal sync (Composite sync) Vertical sync (SCL)
3. Front Panel Function Control Description “Main Menu Controls” Main Menu with OSD controls Front Control Panel shown below in detail Power light Displays the control screen Blue = ON for the highlighted control. Orange = Power Saving Also toggles between two controls on some screens.
Page 8
Do the following to adjust the display setting: 1. To display the Main Menu, press button [1]. NOTE: All OSD menus and adjustment screens disappear automatically after about 15 seconds. This is adjustable through the OSD timeout setting in the setup menu. 2.
Main Menu Controls Adjust the menu items shown below by using the up and down buttons. Control Explanation Auto Image Adjust automatically sizes, centers, and fine tunes the video signal to eliminate waviness and distortion. Press the [2] button to obtain a sharper image.
Page 10
Information displays the timing mode (video signal input) coming from the graphics card in the computer, the LCD model number, the serial number, and the ViewSonic® website URL. See your graphics card’s user guide for instructions on changing the resolution and refresh rate (vertical frequency).
Page 11
Control Explanation Setup Menu displays the menu shown below: Language Select allows the user to choose the language used in the menus and control screens. Resolution Notice advises the optimal resolution to use. OSD Position allows the user to move the OSD menus and control screens. OSD Timeout sets the length of time the OSD screen is displayed.
4. Circuit Description ISP Instruction 1The tool for ISP An i486 (or above) personal computer or compatible. Microsoft operation system Windows 95/98/2000/XP. “ISP_Tool V4.4.1.0” program Software ISP SN Alignment kits The kit contents: ISP BOARD x1 Printer cablex1 VGA CABLE X1 2Connect the ISP board as follow: 3 The process of ISP write is as follows: ,running the program as follows:...
Page 13
b. Select sure, Click icon, search the program ” VA1616W-TSUM16AWR-CMOM156B1L01-L11G-V103a-081015-DE6F.bin” and click save:...
Page 14
C. Click icon, then click . If it burns successfully, it will show as the follow picture:...
DDC Instruction 1 General DDC Data Re-programming In case the main EEPROM with Software DDC which store all factory settings were replaced because a defect, repaired monitor’ the serial numbers have to be re-programmed. It is advised to re- soldered the main EEPROM with Software DDC from the old board onto the new board if circuit board have been replaced, in this case the DDC data does not need to be re-programmed.
Page 16
3 The process of analog DDC write is as follow: ,appear as follow Figs: Double-click Press “program”,it will show “PASS”,it means download OK. Note: The way of digital DDC write is the same as analog DDC write.
5. Adjustment Procedure 1. All Modes Reset You should do “All Model Reset” (Refer to Chap 3. Hot Keys for Function Controls) first. This action will allow you to erase all end-user’s settings and restore the factory defaults. 2. Auto Image Adjust The Auto Adjust is aimed to offer a best screen quality by built-in ASIC.
Page 18
Full Screen 25% White (Gray) Inspection Item: Particle, Line Defect & Mura 8. 50 Gray Test Signal: 1280*1024@60Hz Test Pattern: Full Screen 50% White (Gray) Inspection Item: Bright Dot, Particle, Line Defect & Mura 9. White Box Test Signal: 1280*1024@60Hz Test Pattern: Window standard pattern Inspection Item: Particle, Line Defect, Power, Image Remain &...
Page 19
12. Green Test Signal: 1280*1024@60Hz Test Pattern: Full Screen Green Inspection Item: Bright Dot, Partial & Line Defect 13. Blue Test Signal: 1280*1024@60Hz Test Pattern: Full Screen Green Inspection Item: Bright Dot, Partial & Line Defect 14. Gray_Scale_0-100_V64 Test Signal: 1280*1024@60Hz Test Pattern: Vertical 64 (256) Gray Scale (Right →...
Page 21
Figure 7 Figure 8 Factory Defaults Item Defaults Item Defaults Contrast Input Priority Brightness 100% Resolution Notice Color Temperature 6500K Volume Sharpness 100% Balance OSD H. Position Treble OSD V. Position Bass OSD Time Out ON for E / G / P model Off for M model only OSD Background 1280x768 / 1366x768...
Page 23
Loose or broken pins in the cable connector could cause an improper connection. • Connect the LCD display to another computer. • If you have an older graphics card, contact ViewSonic® for a non-DDC adapter. Control buttons do not work • Press only one button at a time.
Page 27
According to NDS's request to change According to NDS's request to move type of R101 from 0402 to 0603. the capacitors(C102, C103). H_Sync R101 0R05 1/10W 5% R102 100R 1/16W 5% DSUB_H V_Sync R103 100R 1/16W 5% FB102 DSUB_V R104 C101 VGA_B+ DSUB_B+...
Page 29
R434 has to be changed from 0805 to 1206 PANEL_VCC CN403 PA[0..1] PB[0..9] PA[0..1] PB[0..9] R434 C420 PA[4..9] PA[4..9] 330 OHM 1/4W 0.1uF/16V CMVCC 2006-11-7 Add pull up 4K7 to MVCC AO3401L CMVCC R433 C419 R435 10K 1/16W 5% 0.1uF/16V PANEL_VCC 4K7 1/16W 5% Q405...
Page 30
Due to current limit is too low, change from 93G1004-3 to 93G3004-3. 3/16 BAT54C : IF 10mA,VF=0.4V CMVCC DSUB_5V BAV70 IF 10mA,VF=0.855V(drop voltage too much) 5, 6 CMVCC DSUB_5V 5 VCC3.3 VCC3.3 CN404 BAT54C VCC3.3 D401 R437 R439 CMVCC1 SM340A D402 10K 1/16W 5% 10K 1/16W 5%...
12. Different Parts List Diversity of T67MRHDD2WVSNND compared with T67MRHDD2WV3N2 Location Part No. Description Remark N37G0023 1 HINGE 41-D022650 N40G000196870A S/N LABEL FOR VA1616W EDIDVSC16A003 CHECKSUM 0X9E N41G6002968 5A MANUAL N41G780P968 1A WARRANTY CARD- 78-D021250 F40G 16N968 5A SAFETY LABEL N40G000296838A Energy Star Label N40G000296810A...
Page 52
Reader’s basic dada: Name: Title: Company: Add: Tel: Fax: E-mail: After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile 1-909-839-7943. You may also e-mail any suggestions to the Director, Quality Systems & Processes (marc.maupin@viewsonic.com)