Advertisement
Available languages
Available languages
MODELO 2515
ARMADO
1. Para facilitar el armado, recueste el Ventilador de modo que la
parrilla negra y el tablero de control den hacia arriba.
2. Localice el Cable Eléctrico en la parte inferior del Ventilador.
Coloque el Cable Eléctrico en los Canales Para Cable de los
Soportes De Columna . Encaje firmemente los Soportes De
Columna el uno con el otro de modo de formar un Conjunto De
Soportes De Columna . (Figura 1)
3. Una el Conjunto De Soportes De Columna a la Base Del Motor
con (4) Tornillos M5 de 1/2"de largo . Cerciórese de alinear la
Llave del Conjunto De Soportes De Columna con la Muesca
Localizadora de la Base Del Motor . (Figura 1)
Conjunto De Soportes De Columna
Base Del
Tornillos
Motor
M5 de 1/2"
Soportes
De Columna
Canales
Para Cable
Muesca
Localizadora
Llave
Cable
Eléctrico
Soportes
De Columna
4. Arme las Bases de Soporte, introduciendo las Copas en la Base
de Soporte A en los Orificios De Copas de la Base de Soporte
B . Pase el Cable de Electricidad por el orificio grande en el
centro del Conjunto de la Base de Soporte. (Figura 2)
Conjunto de la Base de Soporte
-
Vista des de Arriba
Cable
Eléctrico
Base de
Soporte A
Base de
Copas
Soporte B
Rev. C 9/04
5. Fije los Tornillos (2) #8 X 1/2" en los cuatro orificios que se
encuentran en la parte inferior de la base. (Figura 3)
Conjunto de la Base de Soporte
Vista des de Abajo
Conjunto
de la Base
de Soporte
#8 X 1/2"
Tornillos
6. Alinee el Conjunto de la Base de Soporte con el Soporte de
Columna , cerciorándose de que el canal del cable en la parte
inferior de la base de soporte esté orientado hacia la parte
posterior del Ventilador. Ensamble el Conjunto de la Base de
Soporte con el Conjunto del Soporte de Columna utilizando
los Tornillos M5 de (4) 1" de largo. Jale con cuidado toda holgura
excesiva del Cable de Electricidad e introdúzcala por el Canal
Conductor de Cable . (Figura 4)
Figura 1
Conjunto de Columna Para la Base
Conjunto De
Soportes De
Columna
Conjunto
Cable
de la Base
Eléctrico
de Soporte
Figura 2
M5 X 1"
Tornillos
6
OPERATION
This Fan may be operated by the Manual Controls located on top
of the unit (as shown in Figure 5 ) or by the Remote Control
(shown in Figure 6) .
-
1. Remove the Fan from the carton and assemble as instructed.
2. Place the Fan on a firm, level surface.
WARNING:
Plastic or rubber tabs, like the feet on this unit, may
stick to hardwood floors. The unit may leave a residue that could
darken, stain or leave permanent blemishes on the finish of certain
hardwood floors.
3. Plug the power supply cord into a 120 V~ electrical outlet. Be
sure plug fits tightly in outlet.
4. When the Fan is plugged in, there will be a "beep" to indicate
there is power to the unit.
5. Turn the Fan ON by pressing the Power Button ( ). The Fan will
"beep" twice to indicate that the unit has been turned ON.
6. SPEEDS: Press the Fan Speed Button ( ) to desired speed
setting. Each time the Fan Speed Button is pressed, the speed
will change from Low (1), to Medium (2), to High (3). When intially
Cable
plugged in, the Fan will be in Low Speed. When the Fan is turned
Eléctrico
OFF and ON again, the unit will resume the speed at which it
Figura 3
was turned OFF.
7. OSCILLATION: Press the Oscillation Button ( ) to start and
stop the oscillation function.
8. TIMER: The timer function allows the unit to be set to operate
for a length of time from 1/2 hour to 7 1/2 hours, in increments of
a 1/2 hour. Press the Timer Button ( ) to set the length of time
desired. Each time the timer button is pressed, the time is
increased by 1/2 hour. After reaching 7 1/2 hours, pressing the
timer button once more will reset the Fan to continuous running.
The lights on the front of the unit will light up appropriately with
the length of time that the Fan is set for.
9. SLEEP: This function allows the unit to be set in Sleep Mode.
Pressing the Sleep Button ( ) once will set the unit on Low for
6 continuous hours. Pressing the Sleep Button ( ) a second
time will reset the unit to 6 continuous hours. The Oscillation
Button ( ) will function when the Fan is in Sleep Mode. Pressing
any other button (Timer, Fan Speed or the Power Button) will
shut off the Sleep Mode.
10.To turn the Fan OFF, press the Power Button ( ) and unplug
the unit from the electrical outlet.
Canal
Conductor
de Cable
Figura 4
Rev. C 9/04
2515ES
MODEL 2535
MODEL 2515
REMOTE CONTROL
1. Install the two "AAA" batteries supplied as shown in Figure 6 .
2. The Remote Control Power Button is labeled as ( ).
3. All the functions performed with the Remote Control work
identically to the Manual Controls.
Front of
Remote
If you lose your remote control, please call Customer Service to
order a replacement at 1-800-233-0268, Monday through Friday,
between the hours of 8:00 a.m. and 5:00 p.m. EST.
MAINTENANCE
WARNING:
ALWAYS UNPLUG THE CORD BEFORE MOVING
OR SERVICING.
WARNING:
DO NOT IMMERSE FAN IN WATER!
CLEANING: Clean the Fan with the vacuum brush attachment
on your vacuum cleaner. This will remove dirt and lint that may
accumulate over time. DO NOT ATTEMPT TO TAKE APART
FAN. Clean the body of the Fan with a soft cloth.
CAUTION:
Do not use gasoline, benzine, thinner, harsh clean-
ers, etc. as they may damage the Fan. NEVER use ALCOHOL
OR SOLVENTS.
SERVICING: All other servicing, with the exception of general user
maintenance, should be performed by an authorized service repre-
sentative. Call 1-800-233-0268, Monday through Friday, between
the hours of 8:00 a.m. and 5:00 p.m. EST for the location of your
nearest service center.
STORAGE: Store the Fan, with these instructions, in a cool, dry place.
Remote Storage
Figure 5
3
(Figure 6)
Back of
Remote
Figure 6
2515ES
Advertisement
