Special Tools - Kaiser-Jeep Jeep CJ-3B Service Manual

u
M I S C E L L A N E O U S
U - l l . SPECIAL TOOLS
Below are listed the tools applicable to models
covered in this manual. These special tools are
essential not only for the time they will save but
also because many operations described cannot be
performed without them.
Note; Tools W-274, W-283, and W-285 are univer-
sal and can be used on all engines.
Tool Description
H U R R I C A N E F4 E N G I N E
W-172 Puller, Timing Gear, U-Joint Flange, Vibration Damper
W-231 K i t , Flywheel Dowel Installing
W-238 Driver, Intake and Exhaust Valve Guide
W-2 74 Pliers, Spark Plug Terminal Removal and Installing
W-283 Gauge, F a n Belt Tension
W-285 Studs, Oil Pan Gasket Aligning
C-690 Scale and Gauge, Piston Fitting
D A U N T L E S S V - 6 E N G I N E
W-274 Pliers, Spark Plug Terminal Removal and Installing
W-283 Gauge, F a n Belt Tension
W-285 Studs, Oil Pan Gasket Aligning
W-323 Rear Main Bearing Cap Remover Bolt
W-338 Piston Pin Remover and Installer Set
J-6047-1 Support, J-6047-3 Spring,
J-6047-4 Driver, J-6047-5 Collar, J-6047-20 Pilot
C-690 Scale & Gauge, Piston Fitting
J-5127-2 Carburetor Float Gauge
J-5830-1 Reamer, .004" [0,102 mm.] Oversize
E l e c t r i c a l G r o u p
C-3858 Installer, Rotor, Housing and Shaft Bearing Assembly
C-3935 Driver, Alternator Rotor Bearing (Small)
C-3936 Puller, Alternator Rotor Bearing (Small)
C-4068 Puller, Alternator Rotor Bearing (Large)
T r a n s m i s s i o n G r o u p
KF-128-A Driver, Main Drive Shaft Bearing
W-166 Arbor & Sleeve, Countershaft Needle Bearing Aligning
W-193 Arbor, Countershaft Needle Bearing Aligning
W-194 Plate, Transmission Main Shaft Retaining
W-329 Puller — Main Drive Gear and Mainshaft Bearing (used with SP-5350 Adapters)
W-331 Driver Set — Main Drive Gear and Mainshaft Bearing (used with SP-5361 Driver Heads)
W-334 Thrust Yoke Tool — Second-Third Synchronizer Clutch Protecting
W-335 Arbor — Countershaft Needle Bearing Aligning
W-336 Arbor — Reverse Idler Shaft Needle Bearing Aligning
C-3105 Driver, Mainshaft Rear Oil Seal (2WD)
T r a n s f e r C a s e G r o u p
W-130 Thimble & Driver, Shifter Rod Oil Seal
W-131 Thimble & Driver, Pinion Shaft Rear Bearing Cone
W-133 Driver, Speedometer Drive Pinion Bushing
W-139 Driver, Output Shaft Front Bearing Cone Removing
W-141 Ring, Output Shaft Front Bearing Cone Removing
W-143 Driver, Output Shaft Front & Rear Oil Seal Installer
W-176 Puller, Shift Rod Oil Seal
W-192 Pilot Pin, Transfer Case Intermediate Gear
Thrust Washer
W-251 Puller, Pinion Shaft Oil Seal, Transfer Case Front
and Rear Oil Seal Removing
U n i v e r s a l J o i n t G r o u p
W-162 Tool, U-Joint Flange Installer
W-220 Jig & Bushing, Power-Take-Off U-Joint Pin
Remover & Installer
C-3281 Wrench, U-Joint Holding
360