Download
Share
Print this page
  1. Manuals
  2. Brands
  3. AZON COLOR Manuals
  4. Cutter
  5. CC48
  6. User manual

AZON COLOR CC48 User Manual

Cc series contour cutter
Hide thumbs

Advertisement

Quick Links

Download this manual
AZONCOLOR CC SERIES
CONTOUR CUTTER
USER MANUAL
V.1.1 SEPT
2014

Advertisement

loading

Summary of Contents for AZON COLOR CC48

  • Page 1 AZONCOLOR CC SERIES CONTOUR CUTTER USER MANUAL V.1.1 SEPT 2014...
  • Page 2 V.1.1 SEPT 2014...
  • Page 3 1. Important Information Before you use the cutting plotter, please make sure that you have read the safety precautions and instructions below. Notes, Cautions, and Warnings...

  • Page 5: Stand (Optional)

    3. Set up your cutting plotter 3.1 Stand (optional) CAUTION: Must use M5*45 screws with washers. Must use M5*10 screws to fix the cutting plotter to the stand. 3.2 Connect your cutting plotter 3.2.1 Connect the AC cable Connect the AC cable to the AC connector on the plotter and to the electrical outlet.
  • Page 6 3.2.2 Connect the USB cable (optional) If you want to use the USB cable, you have to install the USB driver. 1.Find the following files from the CD, Double-click CDM20814_Setup.exe connect USB cable with computer，it will display ‘ Found New Hardware’ as follow window. 3 3 .Click “NEXT”...
  • Page 7 4. Click “Finish” ○ ．If driver was installed successfully，You can find a new port in Device Manager, shown as below if you want to modify the default port No. of USB driver, just right-click port（COM3）as shown above, and select “Properties” in context menu.
  • Page 8 Select “Advanced…”, Select the Port Number. that you want to modify, then press “OK” 3.2.3 Connect the RS-232 cable (optional) When you want to connect the RS-232C cable, you must observe the following notes NOTE (1) When connecting the cables, turn off first the power to the device and that to the host computer which the power cable is to be connected.

  • Page 9: Blade Installation

    3.3 Blade installation Figure 3-1 and 3-2 are the drawings of the blade holder. Figure 3-1 Figure 3-2 How to install a blade (1) Remove the blade sheath by rotating it. (2) insert the blade into the hole of the blade handle. (3) Adjust the blade tip to suitable length by rotating the adjusting knob and blade sheath clockwise or count-clockwise.
  • Page 10 3.5 loading a sheet Either a piece of sheet or a roll of sheet can be loaded on the plotter. Figure 3-3 Figure 3-4 (1) Lift the lever to rise the pinch rollers. (see Figure 3-3) (2) Load the sheet and slide to under the pinch rollers form either the front side or backside. The alignment ruler on the platen will help you to adjust the sheet precisely.

  • Page 11: Advanced Operations

    5. Advanced operations 5.1 Cut in FlexiSTATER AZONColor Edition (1) Install the software (2) After finishing the installation, run the Production Manager, Click “Setup”->”Add setup…”. (3) Select the names of brand and model upon your plotter, and click “Next”...
  • Page 12 (4) Set parameters as below: (5) Click “Finish”.
  • Page 13 5.3 Cut 5mm or smaller letters To achieve the best quality output, we suggest you use a narrow sheet. If use wide sheet, you should: (1) Position two pinch rollers as close as possible to both edges of the cutting area. (2) Make sure the loaded sheet is placed the flat with equal tension.
  • Page 14 ○ In ARTCUT: 5.4 Contour Cut (optional) (1) If you are the first time to use this function, you should set the distance between red dot and pen firstly (see P17-4.5 (2) Create or open a graphic file in Flexi, and click “Effects”->”Contour Cut…” to create a contour.
  • Page 15 (3) A djust related parameters in “DesignCentral” pop-up window, and then click...
  • Page 16 “Effects “Contour Cut Mark…” to add a contour cut mark for the graphic file. Click ”-> (5) Select “4 Point” in “DesignCentral” pop-up window, and then click...
  • Page 17 (6) Click file “File” “Print” to print the graphic file. -> (7) In the “Print” window, there are some print options for your choice (e.g , if you want to print original size, just select “100cm = 1m [100%]”)
  • Page 18 (8) Load the printed sheet on the plotter, and click file “File” “Cut Contour…” ->...
  • Page 19 (9) In “Cut Contour” window, select your plotter model, and click “Options” tab -> “Edit…” button.
  • Page 20 (10) It will pop up a dialog box, please set the parameters Offset X 0.00mm, Offset Y 0.00mm as below, and click “Apply”-> “OK”. (11) Then click “Send”, It will pop up a “Alignment” dialog box in “Production Manager” window, select “Interactive alignment (Manual)”,and click “OK”. (12) It will popup the first point dialog box, make the red dot of the plotter aim at the center of the mark by clicking 4 arrow keys, and then click “OK”.
  • Page 21 (13) Then it will popup the second point dialog box, and At the same time, the red dot moves to the second point automatically, make the red dot of the plotter aim at the center of the second mark by clicking 4 arrow keys, and then click “OK”. (14) The operations for the third and fourth points are similar as above.

  • Page 22: Wireless Control (Optional)

    (15) Then it will pop up a dialog box as blow, press Origin button on control panel of plotter. And then press “OK”, the plotter will perform the contour cut. 5.5 Wireless control (optional) How to use WIFI with Flexi soft 1.
  • Page 23 2. Click the cut icon to display a cutter checkbox below the cutter listing 3. Click ”setup” and then select “add setup”...
  • Page 24 4. Select AZONColor and your model from the available dropdown menus. After you select your AZONColor CC series product, click “NEXT”...
  • Page 25 6. Choose “TCP/IP” connection from the dropdown list to display the following dialog box. Input IP address and port number, then click “OK”. 8. After you click “Finish”, your new AZONColor CC Series cutter will be available from the Cut/Plot device dropdown menu.
  • Page 26 WiFi Setup 1.Open “network connections”, click right-button of mouse on “wireless Network Connection”, click “properties” 2. Select “Internet Protocol (TCP/IP)”,click “properties”...
  • Page 27 3.Select “use the following IP address” ,Input IP address and subnet mast and default gateway. (caution: subnet mast must be 255.255.255.0, default gateway must be 192.168.0.1.) 4.click “ok” 5. click right-button of mouse on “wireless Network Connection”,click “view Available wireless networks”...
  • Page 28 6.Chose a wireless network for “WIFI-XXX”,and click “connect” 7. display connected is Ok,Close this Box,...
  • Page 29 Find More Information and Resources. Please visit our Website: http:/www.azonequipment.com/ If you have any questions, please contact us or email to info@ azonequipment.com Information in this document is subject to change without notice. Reproduction of these materials in any manner whatsoever without the written permission of AZONColor lnc.

This manual is also suitable for:

Cc64