Advertisement
Leg Angle Adjustment Lock
Reversible Center Column
Rubber Foot
1
2
3
1/4-20 + 3/8
Mounting Screw
Locking
Nut
Wrench
4
5
6
Unlock
Lock
Center Column
Locking Knob
Retractable
Weight Hook
Leg Lock Grip
Interchangeable
Spiked Foot
(on select models)
7
8
SETUP
Head Mounting
(FIGURES 1 & 2)
If your Tripod did not come with a Head,
select one of the fine Benro Ballheads or
Panheads that match your size Tripod and
install by screwing the Head clockwise
onto the 3/8" Mounting Thread of the Top
Plate. Once it is hand tight, secure by fully
tightening the Head Locking Screw(s) (on
select models) from below.
Most Heads have a 3/8" base mount so
your Benro Tripod is shipped with the
3/8 Mounting Thread exposed, but if the
Head you choose uses a 1/4–20 you can
attach it by simply reversing the Mounting
Screw. To do this turn the Locking Nut
counter-clockwise (using the supplied
Wrench) until it becomes loose, and
unscrew the Mounting Screw until it can
be completely removed. Reverse the Screw,
so that the threads are in position and
screw it back into place, secure with the
Locking Nut using the Wrench.
NOTE: Allow enough of the screw threads
to be available for maximum security
when the Tripod Head is mounted onto
the Tripod. It's recommended that at least
5 to 6 threads be exposed before locking
the Mounting Screw in place.
OPERATION
Before using your Tripod, adjust each Leg
Section to the desired height and Leg
Angle Setting.
Make sure that the Tripod is firmly resting
on a level surface and mount your camera
securely on the Tripod Head. Always
engage any safety locks on the Tripod Head
to prevent any accidental dismounting.
FOR BEST RESULTS: Do not raise the Tripod
higher than necessary and extend the
largest diameter Leg Sections first. Only
extend the Center Column if required to
reach maximum height or to fine-tune the
vertical position.
FOR EXTRA STABILITY: Carefully hang
your camera bag or other weight on the
Retractable Spring-Loaded Weight Hook at
the bottom of the Center Column.
NOTE: Never carry your Tripod with camera
gear attached.
Leg Angle Adjustment
(FIGURE 3)
To accommodate uneven terrain, awkward
shooting situations or for low angle shooting,
your Benro Tripod includes a 2-position Leg
Angle Adjustment Sliding Lock. Each Leg can
be adjusted by pulling the Leg Angle Lock
out and selecting one of the two positions.
Please make sure that the Leg Angle Lock is
securely pushed back into the lock position
after you have selected the desired Leg Angle.
After use, the Leg Angle Adjustment Sliding
Lock releases the Travel Angel's unique
Tripod Legs so they can be folded up 180°
making it extremely compact for easy
carrying and packing.
Leg Section Adjustment
(FIGURES 4 & 5)
Each Leg section can be adjusted to the
desired length by turning the leg lock grip
1/2 turn (180°) clockwise until the Leg is free
to slide in or out. Once the desired length is
achieved, turn the Leg Lock Grip counter-
clockwise until the Leg Section is securely
locked. Repeat this step for each Leg and
each Section until the Tripod is set to the
desired height.
NOTE: To prevent any accidental damage
to your gear, always remove any mounted
equipment (camera, etc.) from the Tripod
before adjusting the Leg Sections.
Raising and Lowering the Center Column
(FIGURE 6)
To raise or lower the Center Column, turn
the Center Column Locking Knob clockwise
and set the Column to the desired position.
While holding the Column in position, turn
the Center Column Locking Knob counter-
clockwise to secure the Column in place.
Don't over-tighten the Center Column Lock,
as this could damage the threads.
NOTE: Take special care when raising or
lowering the Center Column, if a camera or
equipment is mounted on the Tripod. Never
loosen the Center Column Locking Knob
without holding the Center Column. Failure
to follow these instructions could result in
damaged equipment.
Reversible Center Column
(FIGURES 7 & 8)
Your Tripod has the ability to reverse the
Center Column for close-up photography,
copy work and for difficult to reach objects.
To reverse the Center Column, unscrew the
Retractable Weight Hook located on the
bottom of the Center Column. Loosen the
Center Column Locking Knob and pull
the Center Column out. Insert the Center
Column through the bottom with the
Mounting Plate upside-down and retighten
the Center Column Locking Knob securely.
The Center Column has an anti-twist groove
(on select models), be sure to line-up the
groove with the key before inserting the
Column back into the Main Casting.
NOTE: Do not reverse the Center Column
when a camera or equipment is mounted.
(continued on back page)
Advertisement
