Table of Contents
Advertisement
Material Safety Data Sheets
SECTION 1 PRODUCT AND COMPANY IDENTIFICATION
Chevron Clarity® Hydraulic Oil AW
Product Number(s): CPS230340, CPS230341, CPS230342
Synonyms: Chevron Clarity® Hydraulic Oil AW ISO 46
Company Identification
Chevron Texaco Global Lubricants
6001 Bollinger Canyon Rd.
San Ramon, CA 94583
United States of America
www.chevron-lubricants.com
Transportation Emergency Response
CHEMTREC: (800) 424-9300 or (703) 527-3887
Health Emergency
Chevron Texaco Emergency Information Center: Located in the USA. International collect calls accepted. (800) 231-
0623 or (510) 231-0623
Product Information
email : lubemsds@chevron.com
Product Information: (800) LUBE TEK
MSDS Requests: (800) 414-6737
Chevron Clarity® Hydraulic Oils AW ISO 32, 46, 68
Chevron Clarity Hydraulic Oils AW are ashless (zinc-free) oils that meet or exceed the performance requirements
of conventional anti-wear fluids while providing an additional level of environmental safety. All grades are
approved Denison HF-O, while ISO 32 and 46 are approved against Cincinnati Milacron P-68 and P-70,
respectively. ISO 46 meets both the Vickers anti-wear requirements of M-2950-S for mobile hydraulic systems and
I-286-S for industrial hydraulic systems. Chevron Clarity Hydraulic Oils AW are inherently biodegradable and pass
the EPA's acute aquatic toxicity (LC-50) test. These oils have substantially better oxidation stability than
conventional hydraulic fluids (18,000 hour TOST life) which equates to greatly extended oil life in severe service
applications. The hydraulic oils are designed for use in the vane-, piston-, and gear-type pumps of mobile and
stationary hydraulic equipment in environmentally sensitive areas. They are especially well suited for applications
that exceed 5000 psi as found in axial piston pumps.
SECTION 2 COMPOSITION/ INFORMATION ON INGREDIENTS
COMPONENTS
/ CAS NUMBER
/ AMOUNT
Non-hazardous additive blend in refined oil
/ MIXTURE
/ 100%weight
SECTION 3 HAZARDS IDENTIFICATION
IMMEDIATE HEALTH EFFECTS
Eye: Not expected to cause prolonged or significant eye irritation.
Skin: Contact with the skin is not expected to cause prolonged or significant irritation. Not expected to be harmful
to internal organs if absorbed through the skin. High-Pressure Equipment Information: Accidental high-velocity
injection under the skin of materials of this type may result in serious injury. Seek medical attention at once
should an accident like this occur. The initial wound at the injection site may not appear to be serious at first; but,
if left untreated, could result in disfigurement or amputation of the affected part.
Ingestion: Not expected to be harmful if swallowed.
Inhalation: Not expected to be harmful if inhaled. Contains a petroleum-based mineral oil. May cause respiratory
irritation or other pulmonary effects following prolonged or repeated inhalation of oil mist at airborne levels above
the recommended mineral oil mist exposure limit. Symptoms of respiratory irritation may include coughing and
difficulty breathing.
SECTION 4 FIRST AID MEASURES
Eye: No specific first aid measures are required. As a precaution, remove contact lenses, if worn, and flush eyes
with water.
Skin: No specific first aid measures are required. As a precaution, remove clothing and shoes if contaminated. To
remove the material from skin, use soap and water. Discard contaminated clothing and shoes or thoroughly clean
before reuse.
Ingestion: No specific first aid measures are required. Do not induce vomiting. As a precaution, get medical
advice.
Inhalation: No specific first aid measures are required. If exposed to excessive levels of material in the air, move
the exposed person to fresh air. Get medical attention if coughing or respiratory discomfort occurs.
Note to Physicians: In an accident involving high-pressure equipment, this product may be injected under the
skin. Such an accident may result in a small, sometimes bloodless, puncture wound. However, because of its
driving force, material injected into a fingertip can be deposited into the palm of the hand. Within 24 hours, there
is usually a great deal of swelling, discoloration, and intense throbbing pain. Immediate treatment at a surgical
emergency center is recommended.
SECTION 5 FIRE FIGHTING MEASURES
Leaks/ruptures in high pressure system using materials of this type can create a fire hazard when in the vicinity of
ignition sources (eg. open flame, pilot lights, sparks, or electric arcs).
FIRE CLASSIFICATION:
OSHA Classification (29 CFR 1910.1200): Not classified by OSHA as flammable or combustible.
NFPA RATINGS: Health: 0 Flammability: 1 Reactivity: 0
FLAMMABLE PROPERTIES:
PAGE 40
Flashpoint: (Cleveland Open Cup) 190 °C (374 °F) (Min)
Auto ignition: NDA
Flammability (Explosive) Limits (% by volume in air): Lower: NA Upper: NA
EXTINGUISHING MEDIA: Use water fog, foam, dry chemical or carbon dioxide (CO2) to extinguish flames.
PROTECTION OF FIRE FIGHTERS:
Hide quick links:
Advertisement
Table of Contents
