Alpha Arsenal Photo EXPRESS E3 Operating Manual
  1. Manuals
  2. Brands
  3. Alpha Arsenal Manuals
  4. Security System
  5. Photo EXPRESS E3
  6. Operating manual

Alpha Arsenal Photo EXPRESS E3 Operating Manual

Gsm motion detector alpha arsenal photo express e3
Hide thumbs
Table of Contents

Advertisement

Quick Links

CONTENTS
1
1.1
1.2
1.3
1.4
1.5
1.6
2
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
3
4
5
GSM MOTION DETECTOR
EXPRESS E3
OPERATING MANUAL
1
3
3
3
4
4
5
5
7
7
7
10
10
11
12
13
13
13
14
15
16
17
17

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Photo EXPRESS E3 and is the answer not in the manual?

Questions and answers

Summary of Contents for Alpha Arsenal Photo EXPRESS E3

  • Page 1: Table Of Contents

    GSM MOTION DETECTOR EXPRESS E3 OPERATING MANUAL CONTENTS DESCRIPTION AND FUNCTION Purpose Technical specifications Motion Detector package contents Motion Detector structural design Keychain Remote Controller structural design Device set-up and operation SET-UP PROCEDURE Preparing the device for operation Setting up the Motion Detector Entering the programming mode Erasing the phonebook and SMS messages Initial programming (set-up)
  • Page 2 Dear Customer! Thank you for choosing our state of the art high tech security product. In order for this product to serve you for a longtime, please familiarize yourself with this operating manual. In the event that you would like to make any suggestions or comments, please do not hesitate to contact us by using the information located at the back of this manual.

  • Page 3: Description And Function

    DESCRIPTION AND FUNCTION Purpose This EXPRESS E3 GSM Motion Detector (further referred to as Motion Detector) was specifically designed to detect penetration of a protected zone and to transmit notification via a call and SMS text message to a GSM standard telephone; also to photograph the penetrated protected zone and transmit an E-mail via GPRS.

  • Page 4: Motion Detector Package Contents

    Motion Detector package contents Motion Detector package contents in accordance with chart 2. Chart 2 - Motion Detector contents Description Quantity GSM Motion Detector EXPRESS E3 AA Batteries LR6 1.5v User manual Keychain (RC) Remote Control BN-3S Motion Detector design structure Structurally the Motion Detector consists of a main body base, a front cover, a rear lid (removable), detector circuit board and GSM module circuit board (refer to fig.

  • Page 5: Keychain Remote Controller Structural Design

    Fig. 2 Motion Detector structural design with rear lid removed. Keychain remote control structural design The keychain Remote Control structural design consists of a base, a cover, button unit (3 button) and a light diode (refer to fig. 3). Inside the keychain Remote Control is a CR2032 Lithium 3v battery. In order to replace the power source, it is necessary to remove the screw, lift the cover, remove the depleted battery and then, observing polarity, install a new battery.
  • Page 6 -auto reset to armed mode; -auto detection of telephone number for remaining Motion Detector SIM card balance and of GPRS* settings; -disarm alarm mode via a telephone call after triggered alarm. *Footnote- for mobile providers T-Mobile, AT&T, Orange & Vodafone. Basic Keychain Remote Control functions The Keychain Remote Control executes the following functions: -arms the Motion Detector using button "A";...

  • Page 7: Set-Up Procedure

    The status message contains the remaining SIM card account balance. When an alarm event is triggered, the Motion Detector transmits an SMS message and places an outgoing call to the 1st (primary) telephone number and then subsequently calls the additional telephone numbers. The Motion Detector will terminate the outgoing call and proceed to call the next telephone in the following case: - When the subscriber is in network, but does not pick up after 30 seconds.
  • Page 8 Chart 4 - Motion Detector Settings Cell# Default Cell label Description Available values position value 1sms 1st telephone number Enter number in the following (primary) for notification format +1********** e.g.:+17180000000 2sms 3sms Enter number in the following Telephone numbers for 4sms format +1********** notification...
  • Page 9 ZadPost Arming delay in seconds Parameter should be between 15-250 sec. ZadOpov Notification delay, after Parameter should be between triggered alarm, in order to 0-250 sec. facilitate disarming seconds EcoBat Battery economy mode 0- Battery economy mode. Disarms via Remote Control only after triggered Alarm.

  • Page 10: Entering The Programming Mode

    Entering the programming mode In order to access the Motion Detector programming mode, execute these following steps in consecutive order. 1. Install the SIM card as shown in fig. 7 fig. 7 SIM card installation 2. Remove the protective insulating insert from the battery contacts as shown in fig. 7. If the protective insulating insert was previously removed, then remove the battery, wait 2 minutes, then re- insert the batteries making sure to observe proper polarity.

  • Page 11: Initial Programming (Set-Up)

    2. Remove the protective insulating insert from the battery contacts as shown in fig. 7 or install batteries observing correct polarity in the event they were previously removed. 3. Not later than 5 seconds after the initial beep, press the button located on the Motion Detector circuit board, keeping it depressed until the start of numerous beeps.

  • Page 12: Adjusting The Settings

    After transmitting an SMS containing settings and values, the Motion Detector resets to the "Disarmed" mode. Set-up verification 1. Press the "A" button on the Remote Controller. The indicator diode will flash yellow, then red and the Motion Detector device will emit a single confirmation beep. The Motion Detector will continue to emit beeps for 40 seconds, during which time the protected zone must be vacated (e.g.

  • Page 13: Adding A Telephone Number For Notification Messages

    Adding a telephone number for notification messages There are two methods to add a telephone number notification messages. First method: 1. Access the Motion Detector programming mode (see 2.3). For a span of 3 minutes, the Motion Detector will stand by to receive incoming calls. 2.

  • Page 14: Installing The Motion Detector

    2.10 Installing the Motion Detector Install the Motion Detector in the zone to be protected at a location where it will be protected from exposure to atmospheric precipitation, physical damage and access by any unauthorized personnel. The Motion Detector should be installed in a manner that takes into account the likely path of a violator crossing into and through the axis of the protected zone.

  • Page 15: Arming And Disarming The Motion Detector Device

    Warning! After evaluating the detection zone, reset the parameter values at “Opov” to 0 or 1. 2.11 Arming and disarming the Motion Detector device Armed/disarmed alarm modes of the protected zone are controlled via the keychain Remote Controls programmed and registered with the Motion Detector. To arm alarm mode briefly (1-2 sec.) press the “A”...

  • Page 16: Troubleshooting

    Troubleshooting Chart 5 – Troubleshooting Issue Possible reason Solution No sound beeps and GSM light 1. Batteries incorrectly 1. Remove & properly re-insert the diode flashes on the Motion installed; batteries, check polarity; Detector after installing batteries 2. Dead batteries. 2.

  • Page 17: Contact Information

    Contact Information ALPHA ARSENAL LLC 104-20 Queens Blvd., STE 1B Forest Hills, NY 11375, US T/F: +1.718.440.3281 +1.718.355.9281 Skype: alpha.arsenal E-mail: info@alpha-safe.com support@alpha-safe.com Website: www.alpha-safe.com Warranty Coverage The warranty period is one year from date of purchase. During the Warranty period, the manufacturer will repair, exchange, adjust, or replace at its discretion, any defective product.

Table of Contents