Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for ruegg KEA
- Page 1 Operation Manual Pellet stove KEA...
-
Page 2: Table Of Contents
Technology______________________________________________________________________________ 6 Ease of use – operational safety _____________________________________________________________ 6 Highest efficiency – Lowest emissions _________________________________________________________ 6 KEA green in favour of the environment _______________________________________________________ 6 4. Installing the pellet stove __________________________________________________ 7 General instructions _______________________________________________________________________ 7 Electric connection ________________________________________________________________________ 7 Combustion air ___________________________________________________________________________ 7 Connecting the Rüegg room sensor __________________________________________________________ 8... - Page 3 INFO Menu ________________________________________________________________________ 18 Supplementary information ________________________________________________________________ 18 6. Operational sequences and automatic safety functions ________________________ 19 7. Error message __________________________________________________________ 20 Error message (traversing on display): _______________________________________________________ 20 Service menu ___________________________________________________________________________ 20 Faults – causes - measures ________________________________________________________________ 21 Cleaning, warranty, service ___________________________________ 22 8.
-
Page 5: Introduction
Dear customer and you will have long lasting pleasure from your Kea Congratulations to the purchase of your new Rüegg pellet stove! pellet stove. We are convinced that this stove will be a major part of your heating system. If installed by a... -
Page 6: Specifications For High- Quality Pellets
To ensure trouble-free pellet combustion pellets should be stored in a dry and clean place. Technology The KEA pellet stove is optimally suited to be refitted The state of the art of your new pellet stove is with such fine particulate collector by your special ensured by years of laboratory and practice based dealer. -
Page 7: Installing The Pellet Stove
General instructions Electric connection For leveling of the stove the machine mounts under The stove is supplied with an approximately 2.5m long the device can be adjusted in height and locked connection cable with a Euro plug. Connect the cable (counter nut SW13). -
Page 8: Connecting The Rüegg Room Sensor
Safety distances Connecting the Rüegg room sensor For flammable objects: Disconnect stove from the power supply before (Measured from the outside of the stove): connecting the multi-pin plug. Subsequently carefully tighten multi-pin plug on board using screws. -20 cm from the back and the sides -80 cm from the front For non flammable objects: (Measured from the outside of the stove):... -
Page 9: Assembly Dimension
Assembly dimension... -
Page 10: Operation
30%. Your KEA pellet stove can also be operated in fully automatic mode by the thermostat or by selecting the heating time. If you like to use this comfortable mode or want to perform further settings you need to change to advanced operating mode first. -
Page 11: Important Information On How To Use The Menu (Illustrations)
Important information on how to use the menu (illustrations) The illustrations below always depart from the display field in the oval frame. The illustrations in these operating instructions show the display screens and the buttons that have to be pressed in order to access the next screen (in the direction of the arrow). - Page 12 The main menu tree The main menu tree is the departing position for all following illustrations in these operating instructions and all settings for your pellet stove. Instructions on the individual submenus can be found on the following pages below the corresponding number in a circle from this illustration. The main menu tree can only be accessed when in advanced operating mode.
-
Page 13: Changing The Function Mode
Changing the function mode To access this menu item the supplied Rüegg room temperature sensor must be connected. The menu item MODE allows switching between the function modes HEAT, ROOM and AUTO operation. Any other settings for the selected function mode will be made in different submenus which are described in separate illustrations. -
Page 14: Heating In Auto Mode (Automatic Operation)
Heating in AUTO mode (automatic operation) Heating based on pre-selected heating times and temperatures. Before the AUTO mode can be used the current time and date must be entered. For information on how to do that see page 166, section 3 “Setting time and date“. After the time has been set the heating times can be programmed. -
Page 15: Programming The Heating Times
Programming the heating times You may either program each day individually (DAY) or program the same times for the complete week in a superposed program level (WEEK). In order to shorten the entering process it is recommended to program the complete week and subsequently change individual days, if required (e.g. -
Page 16: Setting Of Time And Date
Setting of time and date Departing point is from the number main menu tree (see page 12) Device settings (Setup) Refer to illustration on following page. Various settings can be made in the menu item SETUP: FROST = activating/deactivating of the frost protection function If the frost protection function is set to “FROST On“... - Page 17 Continued from page16 Departing point is number from main menu tree (see page 12) Frost protection function (on/off) Indoor air fan (on/off for optional indoor air fan GSM setup External release for third party thermostats (on/off) GSM functions (on/off) Text message confirmation or error message to mobile phone (on/off)
-
Page 18: Info Menu
INFO Menu The menu item INFO shows information mainly used by the service partner. Inputs Outputs Parameter Departing point is number from main menu trees Screw conveyor (see page 12) Operating hours Flame temperature Feeding interval Pellet amount fed pellets (Kg) Room temperatures Software version... -
Page 19: Operational Sequences And Automatic Safety Functions
Overheating Power failure during operation A safety temperature limiter (STB) will stop the stove After a power failure the flame temperature will be automatically when overheated. After cooling down of checked. If the temperature exceeds 300°C the the pellet stove manual reset of the STB is required. device will not attempt to restart but continue the Remove the STB protection cap (see image) and normal operation. -
Page 20: Error Message
Fuel feed of the pellet container is less than 2kg. Check the filling level regularly. The container lid should, IMPORTANT! Avoid contact of pellet bag with the hot however, always be kept closed unless the container stove during fuel feeding! is being filled. -
Page 21: Faults - Causes - Measures
Faults – causes - measures MEASURES PROBLEM/ERROR FAULT DESCRIPTION (Start with first step. If not successful, perform with next DISPLAY step) Check pellet supply and refill pellets, if required (for first start add some pellets manually to the fire pan) “NOT IGNITED“... -
Page 22: Cleaning, Warranty, Service
Light ash can be removed from the side and bottom of manual. We strongly recommend using only tested the fire pan and the containers by use of an ash pellets al fuel for your Kea! vacuum cleaner. Important remark! Caution: Embers may be hidden in the ash – use... -
Page 23: Small Service Procedure
the door opener. This is necessary to prevent an early deviation of the smoke gasses. Cleaning the door glass It is best to clean the combustion chamber door with a wet cloth. Stubborn dirt can be removed with a special cleaner which is supplied with the operating kit. -
Page 24: Service Procedure
Procedure: Remove the bottom convection grate. (lift and pull towards you) Remove cover plate of inspection hole by unscrewing the two hexagon screws (SW10). Clear manifold channel form combustion residues with vacuum cleaner. (see image) Refit parts in the reverse order. Ensure tight fitting! Inspecting the door seals CAUTION! -
Page 25: Options, Accessories And Parts
Procedure: 1. Turn off stove and disconnect from mains supply. On the back of the KEA pellet stove you will find a 15- pin plug (see image), which can be used for 2. Use a small screw driver to loosen the two connection of the Rüegg room sensor as well as of a... -
Page 26: Accessories
Ash-clean ash recipient 20 l, for use with vacuum cleaner 47.60.00000 Glass cleaner, with spray nozzle, 750 ml/ 1 bottle 55.60.00100 Spray paint silver, for KEA/TAOSI, bright metal parts Spare parts list Combustion chamber door Item no. 52.57.00005 Thermo glass for combustion chamber door Item no. - Page 27 Side panel right, anthracite, recessed (KEA II & KEA III) Item no. 52.57.00125 Insert plate silver (1 pc) to side panel left and right for KEA II Item no. 52.57.00130 Natural stone insert for side panel for KEA III (order in pairs, if possible) Item no.
-
Page 28: Warranty/ Customer Service
for all seals Scope of warranty and of liability Excluded from the warranty and/or To enable us to provide our free service in case of a defect during the warranty period, warranty claims, guaranty are: sent us a copy of the “report of system acceptance” Minor deviations of the product regarding the and a copy of the invoice, in order to ensure dimensions, the colour or the design compared... -
Page 29: Service Logbook
Service logbook Please store a copy of the “report of system acceptance” together with this continually updated service logbook The service has to be executed by a certified partner. (Querformat) Signature or stamp Other remarks Flame Auger Chimney connection Electronic components Door position Sealing Cleaning exhaust ducts... -
Page 31: Specifications
Your Rüegg service partner: Your Rüegg partner: Certified Rüegg service partner for: If your Rüegg dealer does not offer the required service (see field on the right) please contact the Nein Initial commissioning Rüegg customer service or the service company below. - Page 32 Rüegg Cheminée AG Rüegg Kamine GmbH Schwäntenmos 4 Biergasse 7 8126 Zumikon 4616 Weisskirchen Schweiz Österreich Tel. +41 (0)44 919 82 82 Tel. +43 (0)7243 56946 Fax +41 (0)44 919 82 90 Fax +43 (0)7243 56946 10 info@ch.ruegg-cheminee.com info@at.ruegg-cheminee.com Rüegg Cheminées S.A.S...
Need help?
Do you have a question about the KEA and is the answer not in the manual?
Questions and answers