T-ONE T-EP01 User Manual

Alarm
Undercover User Manual
A sensor is bulit-in to detect the vibration, while someone is trying to move your bike, the Bike
Guard will alert you in 3 second.
Master&Slave will alarm for 5 seconds and repeat alarm until vibration is stop. Front & Rear View
Disarm Alarm:
Under standby mode, turn OFF the Master unit within 3 meters from your bicycle and wait for the
Front
Distance
approval sound "Di-du" on Master unit. When you hear "Di-du", you have disarmed Bike Guard.
indication
Mute
Press the Mute button to mute searching melody from the Master unit. Listen to beep sound from Signal
indication
Mute
the Slave unit to assist short range searching.
button
Search button
Wake up / Standby
Hanging hole
for strap
a.) Switch Master & Slave power On, Master will enter wake-up process. The Signal indicator, right
and left LEDs blink while Master is waking Slave up within 8~15 seconds if Slave is within range Clip
and NOT being blocked. After Slave been woken up, Master enters Search mode. Press Search
key to go back to Standby mode.

Specifications

b.) Under Standby mode, Master's LED blinks every second. When wake-up, Master enters Search
mode automatically. If Master cannot wake-up Slave within 160 seconds, due to out of range or
T-EP01
Model Name
signal is blocked, it will enter Standby mode and beeps to indicate lost signal. User can push
Search, Alarm, 1 to 1
Function
Search key to enter wake-up process again.
Search Range 0~120m/328ft
Alarm Distance Prolonged Vibration of 3 second
Important: Please turn off the Master unit if NOT in use to save battery life.
Master/Slave Master (M05S)x1 Slave (S07A)x1
Battery Type LR44 CR2032
Out of range or Loss signal
Battery Life Time with Standby 50 days(8 hrs) 60 days (8 hrs)
Battery Life Time with Sleep Over 90 days Over 90 days
a.) Master beeps, vibrates and signal LED blinks for 160 seconds out of range or loss signal;
Beep Sound (at 10cm/3.9inch) 95 db 102 db
then Master will enter sleep mode automatically.
Bulid-in None Vibration Sensor None
b.) master beeps once a minute (to remind user to switch power OFF for Master unit for
52.8x39x13.2mm 38x120x6.2mm
Dimension (L/W/H)
power-saving.)
2x1.6x0.52inch 1.5x4.72x0.24inch
c.) To wake-up Master , press Search button to go to wake-up process.
Getting Start
Low battery
1.For first time use, please insert the batteries into the Master and the Slave sets according to the battery
When the Matser and Slave is under low battery condition, it will beep at a 2 minutes interval,
installation as follows.
please change the battery.
-Master
Important: Under low battery condition, it may cause abnormal function of alarm or searching. b
Please Note
a.) The connection range is based on clear line of sight. Actual range will vary depending
on user's environment and location.
a
b.) When the Master and Slave units are turned ON, it takes 8 to 15 seconds for the synchronization.
c.) The signal will be disconnected while the Master and Slave units are too close within 10 cm (the
signal connection will be overloaded). When the Master unit can't connect to Slave unit, Master
c
unit alarms every second and Slave unit's LED light flashes.
a. Slide out the battery cover.
Care and Maintenance
b. Insert the batteries. Make sure that the
a). The Slave units are water-repellent, but not waterproof! +/-
polarity of the battery follow the markings
on the bottom of the battery compartment.
Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain
minerals that may corrode electronic circuits. If your device gets wet, remove the battery, and
allow the device to dry completely before replacing it.
2.Mark sure the Master is powered OFF in the first place and install the Slave on the bike (in case the alarm is
b). Do not use or store the device in dusty, dirty areas as its moving parts and electronic triggeved while installation) take the Master with you or clip it on your belt.
components can be damaged.
3.Switch the power button of the Master to "ON".
c). Do not store the device in hot areas. High temperatures can shorten the life of electronic device
, damage Batteries, and warp or melt certain plastics.
Front Back
Back
Buzzer
Power on
Power off
Battery cover
Package Contents
Modle Name
T-EP02
Search, Alarm, 1 to 1
Master
0~200m/546ft
Slave
Prolonged Vibration of 3 second
Master (M05A)x1 Slave (S07A)x1 Batteries
LR44 CR2032
User manual
30 days (8 hrs) 60 days (8 hrs)
Strap
90 days Over 90 days
95 db 102 db
Vibration Sensor
52.8x39x13.2mm 38x120x6.2mm
2x1.6x0.52inch 1.5x4.72x0.24inch
c
b
a
c.Place the battery cover back.
d). Do not store the device in cold areas. When the device returns to its normal temperature,
Preferred setting place
moisture can from inside the device and damage electronic circut boards.
e). Do not attempt to open the device other than as instructed in this guide.
f). Do not drop ,knock or shake the device. Rough handling can break internal circuit boards and
fine mechanics.
g). Do not use harsh chemicals, cleaning solvents,or strong detergents to clean the device.
h). Do not paint the device. paint can clog the moving parts and prevent proper operation.
i). Do not put the master and the Slave at same place in case of this kit is unable playing functions
to guard your valued goods.
j). Search, detection, and alarm range depend on the terrain environment.
Search
k). If the beep sound is not loud enough, the batteries may be low. Change with new batteries for
For searching the Slave unit, please press the "Search button" on the Master unit once. If the distance between the
louder alarm sound.
Master and the Slave is closer, more LED lights are lit and the melody from the Master becomes more rapid.
l). This product only assists in providing a warning alarm to remind the user. It does not guarantee
Battery cover Contrarily, if the distance between the Master and the Slave is farther, less LED lights are lit and the melody from
to prevent theft or robbery of personal property.
the Master becomes slower. Use the LED and the melody indication as guides to find the Slave unit.
m). If you want to use the device during flight trips, please comply with the flight safety law
according to each country.
n). We reserve the right in changing the specification of the hardware and software designs to
manuals at any time and without prior notice. Information in this document is subject to change
without notice.
T-EP01/T-EP02 o). This product operational temperature is between 32℉ ~131℉(0˚C~50˚C). Storage Temperature
1 set
is between -4℉~185℉(-20˚C~85˚C) .
Under search mode, always place the Master in front of your body and turn to different
1 set Recycle: The Batteries provided in this product should be recycled to protect the local environment.
directions to check the signal. If you point at the right direction, The master will show
Please contact your local recycle department for detail.
LR44x4 lights and plays the melody more rapidly
Warning: Do not put the batteries into the fire or heat sources. If the distance between the Master and the Slave is out of detectable working range and
CR2032x2
you are turning into the wrong direction making the distance farther , the Master plays the
It may cause danger or even explosion.

melody and beeps every second to remind you to go back to the right direction and detectable

FCC Certifications
distance ASAP.
If you want to stop the search mode, press the "Search button" on the Master unit once.
Federal Communication Commission Interference Statement
While searching, the Slave makes low beep sounds every second. This can assist you in
This equipment has been tested and improved to comply with the limits of a Class B digital device,
finding its position by tracking the sound when the Master and the Slave are already close.
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
(Suggestion: Press and hold the mute button on the Master to turn of
harmful interference in a residential installation. This FCC Certifications equipment generates, uses and
temporarily. Once you release the mute button, the searching melody resumes again.)
can radiate radio frequency energy, if installed and used not in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determinedly turning the
equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:
■ Reorient or relocate the receiving antenna.
■ Increase the separation between the equipment and receiver.
■ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
■ Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept an interference
received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications are not expressly approved by the party responsible for
compliance which could void the user's authority to operate this equipment.
EU Declaration Conformity
This product is carrying the CE-Mark in accordance with the related European Directives.
91E-T1B6-U50G01
bolt
working range 0~120(200)m/328(546)ft
(line of sight) (the distance may be short
depends on the terrain environment )
.
During Search
Correct
Holding
*** Do not sway Master. Master is always in front the body when take a turn.
Holding Way
Correct Wrong
Holding
Holding
*** Do not cover the top side of Master.
Assembled
bottle cage
f the melody
Wrong
Holding