Summary of Contents for Digital View DVC?3GTx
-
Page 1: Table Of Contents
Table of Contents Introduction 3 System 5 Instruction 6 Dimensions 8 HDMI to 3G/HD/SD‐SDI Converter Box Mounting (Optional) 8 DVC‐3GTx Signal Support Mode Table 9 Manual Specification 10 Specification Warranty, Caution & Limitation of ... -
Page 2: Dvc-3Gtx
DVC‐3GTx Key Features 1. Introduction a. Supports 1.5Gbits & 3Gbits bit rate input signal support. The mode support is listed in section 6 – Signal support mode table. The DVC‐3GTx converts HDMI to HD‐SDI for HD‐SDI equipment. The DVC‐3GTx provides another HDMI output for local monitor connection. b. Convert HDMI to 3G/HD/SD‐SDI channels : Compliance with the SMPTE 274M, 296M, 425M (Level A) standards. The LED’s indicates input and output Convert HDMI to HD‐SDI for HD‐SDI equipment and it provides another HDMI output for local HDMI monitor port status. connection. See Figure below : Ordering Information : Part Number Model P/N 586016210‐3 DVC‐3GTx If you have difficulties, please contact your sales representative or Digital View support, contact details are available on www.digitalview.com/dv_contactus.php. IMPORTANT USAGE NOTE The manufacturer accepts no liability for damage or injury caused by the use of this product. It is the responsibility of the developer, integrators or other users of this product to: • Ensure that all necessary and appropriate safety measures are taken. • Obtain suitable regulatory approvals as may be required. • Check power settings to all component parts before connection. ... -
Page 3: System
2. System 3. Instructions 3.1 Preparation This unit is designed to be as plug and play as possible requiring the minimum of setup for use. The following describes the operation of this monitor unit. Please make sure the whole package in the box includes the items below : DVC‐3GTx, P/N 586016210‐3 Power supply ‐ 12V 2A, P/N 500001701‐3 Power cord HDMI cable, P/N 420000900‐3 (2 meter) 3.2 Powering On • Connect the provided external AC power supply unit. • Power on the unit using the Power on/off switch, the status LED should come on. Item Description Function This LED indicates the controller status. 1 HD/SD SDI Output port Output SDI (3G/HD/SD) signal The definition of the HD/SD SDI Input and output port side are : 2 HDMI Output port Output HDMI signal Ref Description 3 Config Setting Configure the operation modes (Switch HDMI Input port side ... -
Page 4: Dimensions
• Config Setting : 4. DIMENSIONS Position Function 1 UP – HD/SD‐SDI receiver operation (e.g DVC‐Rx/HD‐1000/HD‐2000) DN – 3G‐SDI receiver operation (e.g DVC‐3GRx/HD‐3000) 4 UP – Read DDC setting from internal DDC chip DN – Read DDC settings from the external device connected 5 Reserved for factory use (Default = DN) Other position settings are no function. • Connect the appropriate cable connection. 5. Mounting (Optional) This unit offer an optional wall mount plate P/N 366013305 for mounting purpose. Wall mount plate : P/N 366013305 Page 7 of 12 Page 8 of 12... -
Page 5: Signal Support Mode Table
6. SIGNAL SUPPORT MODE TABLE 7. Specification Supported serial interface standard SMPTE 274M, 296M, 425M (Level A) Mode Supported video mode 3G HD‐SDI formats SMPTE 425M : 3G HD‐SDI format : 1080p@50/60Hz (4:2:2) SMPTE 425M 1080p60 (4:2:2) HD‐SDI formats 1080p50 (4:2:2) SMPTE 274M : 1080i@50/59.94/60Hz, HD‐SDI format : 1080p@30/25/24Hz. SMPTE 274M SMPTE 296M : 720p@50/59.94/60Hz 1080i60 (4:2:2) 1080i59.94 (4:2:2) SD‐SDI formats 1080i50 (4:2:2) 480i (NTSC) 1080p30 (4:2:2) 576i (PAL) 1080p25 (4:2:2) Number of channel output port supported 2 1080p24 (4:2:2) Output port HDMI (v1.3) SMPTE 296M SDI 720p60 (4:2:2) Embedded audio Supported with up to 8 channels embedded audio. 720p59.94 (4:2:2) LEDs ... -
Page 6: Contact Details
8. Warranty 13. CONTACT DETAILS The products are warranted against defects in workmanship and material for a period of one (1) year from the Digital View has offices in Asia, Europe and USA : date of purchase provided no modifications are made to it and it is operated under normal conditions and in compliance with the instruction manual. USA The warranty does not apply to: Digital View Inc. • Product that has been installed incorrectly, this specifically includes but is not limited to cases where 18440 Technology Drive Building 130 electrical short circuit is caused. Morgan Hill, • Product that has been altered or repaired except by the manufacturer (or with the manufacturer’s California, 95037 consent). USA • Product that has subjected to misuse, accidents, abuse, negligence or unusual stress whether physical or electrical. Tel: (1) 408‐782 7773 Fax: (1) 408‐782 7883 • Ordinary wear and tear. Sales: ussales@digitalview.com Except for the above express warranties, the manufacturer disclaims all warranties on products furnished ...