Advertisement
SFP Port Options
OSD Part
SFP Description
Number
OSDSFP100Fx
2 fiber SFP @ 1310nm
OSDSFP100WFxA
1 fiber SFP (Tx:1310nm, Rx:1550nm)
OSDSFP100WFxB
1 fiber SFP (Tx:1550nm, Rx:1310nm)
Port Allocation and LED indicators
Ethernet
Port 1/PoE
SFP Port
Ethernet
Port 2
Optical Port LED indicators
3 3 3 3
1 1 1 1
Fiber Link/Act
PoE
Green
-
Link OK
Blinking
-
Link Activity
Red
-
No optical signal received
-
On
PoE On
Copper Port LED indicators
2 2 2 2
4 4 4 4
100Mb/s
Link/Act
(Amber)
-
On
100Mb/s connection
-
Off
10Mb/s connection
On
-
Copper Link OK
Blinking
-
Copper Link Activity
Technical Specifications
Specification
Data Interface
Data Rate
Operating Mode
Data Connector
PoE
PoE
1 1 1 1
Operating Modes
Link/Act
2 2 2 2
Optical Interface
Optical Port
Connector
Transmitter Optical
Power
Fiber Link/Act
3 3 3 3
100Mbps
Receiver Sensitivity
4 4 4 4
2 2 2 2
Link/Act
Receiver Saturation
Standard SM Optical
Link Budget
Fiber Link/Act
4 4 4 4
100Mbps
Power Requirements
Function
Power Connector
Enclosure
Dimensions (mm)
Weight of Module
Operating
Temperature
Relative Humidity
Function
▲
Performance
IEEE 802.3 Ethernet
10/100Mbps
Half or Full Duplex
2xRJ45. PoE on front panel, non-PoE
on rear panel
46 to 50V @ 0.4Amp Maximum
Alternative A (Pins 1/2 and 3/6)
Alternative B (Pins 4/5 and 7/8)
100Base-Fx
SFP - LC for 2-fiber, SC for 1 fiber
-15 to -8dBm into singlemode fiber
(see SFP datasheet for options)
<-33dBm
>-3dB
>10km on multimode fiber @
>18dB:
1310nm
>40km on singlemode fiber
@ 1310nm
+10V
to +35V
DC
DC
22V
to 28V
at 3VA plus up to an
AC
AC
extra 20VA for PoE operation (attached
powered device dependant)
3.5mm 2-way terminal block
Anodised elliptical metal case
52W x 55D x 26H
300g
-20 to 75°C, derated by 3°C/watt
supplied over the Ethernet cable.
Reduces to 30°C when connected to a
15W load
0 to 95% non-condensing
ELECTROMAGNETIC COMPATIBILITY
WARNING: This is a Class A product. In a domestic
environment this product may cause radio interference
in which case the user may be required to take
adequate measures.
Doc. ID 10110803
OPTICAL OUTPUT OPERATION
▲
WARNING: Laser Safety: Class 1 Laser Product
per IEC/EN 60825-1:20011 standard.
Class 1
The OSD2052P is a Class 1 laser product.
Precautions
▲
All service personnel should be provided training as
to the hazards of direct viewing of laser radiation
and of the precautionary measures during servicing
of equipment
Areas where laser products are installed should be
▲
restricted in access to trained service personnel
only and appropriate warning signs posted in the
work area.
▲
All laser apertures should be covered by protective
covers when not connected to optical fibers. Never
leave outputs uncovered.
Laser equipment should be positioned above or
▲
below eye level where possible. Apertures should
be positioned away from personnel
▲
Protective eyewear should be worn in the vicinity of
laser equipment
Warranty/Repairs
Thank you for purchasing equipment designed, manufactured
and serviced by Optical Systems Design (OSD). OSD warrants
that at the time of shipment, its products are free from defects in
material and workmanship and conforms to specifications.
For warranty period and repair service please contact your local
OSD distributor.
OPTICAL SYSTEMS DESIGN PTY LTD
7/1 Vuko Place, Warriewood 2102.
PO Box 891, Mona Vale,
NSW, Australia 1660.
Phone: +61 2 9913 8540
Fax: +61 2 9913 8735
Advertisement
