Notice Malfunction or damage to equipment! Do not install the unit near any direct heat source. Keep the unit away from naked flames. Do not block areas of ventilation. Failure to do so could result in fire. Mix 1832 FX...
Contents Important safety notes ....................2 Introduction ......................... 4 Features ........................4 Useful information ...................... 4 Front side ........................5 Quick start ........................6 Control elements ......................8 Installation and connection ..................16 Audio connections ..................... 17 Operation instructions for music player ..............19 Preset list ........................
All the above features and its audio quality, make it perfect for piano bar, karaoke, as well as fixed PA installation. Enjoy your Mix 1832 FX and please carefully read this manual before operation! Features •...
MIC 4 MIC 5 MIC 5 MIC 6 MIC 6 TAPE IN TAPE OUT TAPE IN TAPE OUT MIX 1832 FX MIX 1832 FX Professional Mixer Professional Mixer LINE IN 1 LINE IN 1 LINE IN 2 LINE IN 2...
Quick start This is the fastest way to get something out from your Mix 1832 FX, if you have a keyboard and a microphone Plug the microphone into Channel 1 MIC IN. Turn down AUX and LEVEL controls on the input channel.
Page 7
MIC 4 MIC 4 MIC 5 MIC 5 MIC 6 MIC 6 TAPE IN TAPE OUT TAPE IN TAPE OUT MIX 1832 FX MIX 1832 FX Professional Mixer Professional Mixer WIRELESS WIRELESS LINE IN 1 LINE IN 1 LINE IN 2...
Control elements Mono MIC/LINE channels Your Mix 1832 FX is equipped with 4 low-noise microphone preamplifiers with optional MIC 1 phantom power, 50 dB of Gain and over 115 dB of S/N ratio. You can connect almost any type of microphone. Dynamic microphones do not need phantom power. Use phantom power for condenser microphones only, but make sure that the phantom power button is disengaged before connecting the microphone.
Page 9
LOW-CUT button By pressing this button, you will activate a 75 Hz low frequency filter with a slope of 18 dB per octave. You can use this facility to reduce the hum noise infected by the mains power supply, or the stage rumble while using a LINE LINE microphone.
PEAK LED Inside your Mix 1832 FX mixer, the audio signal is treated in several different stages and then sent to the PEAK LED. When the LED is red illuminated, it warns you that you are reaching signal saturation and possible distortion.
Control Room Source You can choose to monitor any combination of MAIN MIX, SUB1- 2, SUB 3-4 and 2TK IN via these Matrix switches. Engaging these switches, the stereo signals will be delivered to the Phones, Control MAIN GRAPHIC EQ Room and Meters display.
EQ OFF EQ ON MAIN GRAPHIC EQ DSP SECTION There is a powerful 24-bit/256 preset multi-effects included in your Mix 1832 FX. Effects include reverbs, cho- rus, flanger, delay and combinations of the above. Mix 1832 FX...
PRESETS Adjust this knob to select the effect you wish to perform. There are 16 options for you: several kinds of reverb, mono and stereo delay, effects with modulation, and versatile two-effect combination. ∞ ∞ EFFECTS OUT AUX1 DFX2(INT) RETURNS EFFECTS TO MONITOR VARIATIONS Once you have selected the desired PRESET effect type, then you can choose among the 16 variations the...
AC inlet with fuse holder Use it to connect your Mix 1832 FX mixer to the main AC with the supplied AC cord. Please check the voltage available in your country and how the voltage for your Mix 1832 FX mixer is configured before attempting to connect your Mix 1832 FX mixer to the main AC.
Page 15
MONO Level control This knob sets the level of mono mix output signal, which can be varied from – to +15 dB. ∞ MONO (BAL/UNBAL) output jack This ¼-inch phone jack is balanced/unbalanced mono mix output connector, it can be regarded as a sum out- put of the left and right of MAIN MIX.
Installation and connection Ok, you have got to this point and you are now in the position to successfully operate your Mix 1832 FX. However, we advise you to read the following section carefully to be the real master of your own mix. Not paying enough attention to the input signal level, the routing of the signal and the assignment of the signal will result in unwanted distortion, a corrupted signal or no sound at all.
Audio connections You can connect unbalanced equipment to balanced inputs and outputs. Simply follow these schematics. 2=Hot(+) 2=Hot(+) 1=Ground/Screen 1=Ground/Screen 3=Cold(-) 3=Cold(-) Use for Balanced Mic Inputs Use for Main output (For unbalanced use, leave pin3 unconnected) (For unbalanced use, connect pin 1 to 3) 3-pin XLR Male Plug 3-pin XLR Line Socket (seen from soldering side)
Playing type: MP3 only It can read up to 7 rank folders of your USB flash drive. Operation Instruction 1. When no USB flash drive is inserted, your Mix 1832 FX display will show the following screen: INSERT USB KEY 2.
Preset list Controllable Parameter Preset Description Parameter Variable range Decay time 1.0 ~ 2.9s WARM HALL Simulates a small acoustic space of the sound. Pre-delay 20 ~ 45ms Decay time 3.6 ~ 5.4s BRIGHT HALL Simulates a large acoustic space of the sound. Pre-delay 23 ~ 55ms Decay time...
T1.25 A, 250 VL Main Connection Standard IEC receptacle Physical Dimension (W 415 mm 400 mm 35/115 mm (16.3 × D × H) × × in × 15.8 in × 1.49/4.53 in) Net weight 6.7 kg (14.8 lbs) Mix 1832 FX...
Protecting the environment Disposal of the packaging material For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed and are not in the reach of babies and young children.
Need help?
Do you have a question about the Mix 1832 FX and is the answer not in the manual?
Questions and answers