General Operations; Snooze Control; Usb/Sd Operation - Hyundai H-1550 Instruction Manual

buttons on the unit ( /TUNING and
TUNING buttons on the RC) to set hours of
the 1st alarm (AL1). Press ALARM (ALARM.
SET/MEM-DN) button to save hours; minute
digits will flash. Press repeatedly
/TUN+ ( /TUNING and
buttons to set hours of the 1st alarm. Press
ALARM (ALARM.SET/MEM-DN) button to
save minutes; the unit is in the signal sound
selection mode. Press repeatedly
and /TUN+ ( /TUNING and
buttons to set USB/SD (USB and SD indicators
blinks), radio (FM indicator blinks) or buzzer
(no indicator blinks) as the sound signal of the
1st alarm.
• Press ALARM (ALARM.SET/MEM-DN)
button to save the settings of the 1st alarm.
AL2 indicator will be blinking showing that the
2st alarm is being set.
• Press repeatedly
buttons on the unit ( /TUNING and
TUNING buttons on the RC) to set hours of
the 2nd alarm (AL2). Press ALARM button
(ALARM.SET/MEM-DN button) to save hours;
minute digits will flash. Press repeatedly
/TUN- and /TUN+ (
/TUNING) buttons to set hours of the 2nd
alarm. Press ALARM (ALARM.SET/MEM-DN)
button to save minutes; the unit is in the signal
sound selection mode. Press repeatedly
/TUN- and /TUN+ (
TUNING) buttons to set USB/SD (USB and SD
indicators blinks), radio (FM indicator blinks) or
buzzer (no indicator blinks) as the sound signal
of the 2nd alarm.
• Press ALARM button (ALARM.SET/MEM-
DN button) to save the settings of the 2nd alarm.

General operations

• In any mode, press repeatedly ALARM
button (ALARM.SET/MEM-DN button) to check
settings of 1st and 2nd alarms.
• Ensure that the function switch is in MODE
position and AL1 and AL2 indicators are on,
otherwise the alarm will not work. To switch
off the alarm mode, press and hold SNOOZE
button; AL1 and AL2 indicators will be off.
/
/TUN- and
/TUNING)
/TUN-
/TUNING)
/TUN- and /TUN+
/
/TUNING and
/TUNING and /
Instruction manual
Repeat the operatios again to switch on the
alarm mode.
• Do not select USB/SD as alarm signal
if USB or memory card is not connected,
otherwise the alarm will not work.
• If you want to select radio as alarm signal,
switch to the needed station first.

Snooze control

• When the alarm is on, press SNOOZE
button once, after 9 minutes the alarm will
be on again. This operation can be repeated
several times.
• When the alarm is on, press ALARM
button (ALARM.SET/MEM-DN button) or set
the function switch to another position to stop
the alarm.
• When the alarm is on, if you don't press
ALARM button (ALARM.SET/MEM-DN button),
it will stop after 90 minutes.

USB/SD operation

Playback
• Insert a USB device into the USB port.
Insert an SD memory card into the memory
card slot according to the marking on the unit.
• Set the function switch to USB/SD
position. Playback of the first track contained in
the USB/memory card will start automatically.
If both USB and SD are connected
simultaneously, USB will be played by default.
If you connect an SD card while USB is being
played, the unit will switch to SD card playback.
Press USB/SD button on the RC or press and
hold /MEMO/USB/SD button on the unit to
switch between USB and SD playback. When
USB is being played, USB indicator flashes;
when SD is being played, SD indicator flashes.
• The display starts by showing the number
of the first track for 10 seconds, then the
display shows clock. Press SNOOZE button to
switch between track number and clock display.
• Press /MEMO/USB/SD button on the unit
( /PLAY/PAUSE button on the RC) to pause
5