Advertisement
A few years ago, I was at the Dallas Vintage Guitar Show and
my band was scheduled to perform a few times. A friend said,
"Hey. You need an amp to play through, and I have a friend
who makes great amps." He took me to the booth of a Texas
amp builder, Doug Sewell. I loved the way his amps sounded,
and after barely saying hello, Doug and I were inside rewiring
the amp I was going to play through. Since that day, Doug and I
have spent years rewiring and listening to every single possible
variation to finalize the circuits. Our goal was to have highly
usable and musical amplifiers.
I am not an amp collector. I am an amplifier user who keeps
the amps I am presently playing through. That said, after Doug
and I got several of the prototypes finalized, I sold some of
my old coveted live and studio amps because ours sounded
considerably better. The next step was to take the prototypes
to musicians who are known for their amplifier tone as well as
their playing. What's interesting is that when I spoke to these
artists about trying the amps, they all said the same thing.
"Sure I'll use them, if I love them."
In a real way, amplifiers are musical instruments. They are the
devices that "amplify" the sound of the player's hands, the
guitar and possibly the pedal board. They must share many
qualities. They must work - they have to have a beautiful
balance of bass, midrange, and treble; the highs should be
sweet - not harsh; they should be easy to operate and be
highly musical. In addition, amps should clean up really well
when you turn your guitar down. The final quality that Doug
and I looked for are amps that sound good no matter where
the knobs are. It is a rare quality that we insisted on.
I hope this hand-crafted amplifier gives you years of
enjoyment, musical results, and pride in ownership. I
appreciate your confidence.
Using your PRS Amplifier
IMPORTANT: Before using your amplifier, refer to the IMPORTANT SAFETY INSTRUCTIONS insert
supplied with the product.
Powering Up:
1. Make sure your speaker cabinet is connected to the correct speaker output impedance jack with a
high quality speaker cable. Do not use guitar cords.
2. Make sure the power cord is connected to the correct grounded outlet.
3. Make sure there is at least 6 inches of clearance behind the amplifier to allow for proper cooling.
Never place the amplifier against a wall or other equipment, and keep it clear of other heat sources,
such as other amplifiers or stoves. Make sure there are no flammable items, such as curtains,
behind the amp. Do not drape items over the amps that can prevent proper cooling. Do not set
drinks or other liquids on top of the amp that can spill into the amp.
4. To increase the life of the tubes, set the "Standby" switch to the STANDBY position before
powering on. Turn the POWER switch on and let the amplifier warm up for 2 minutes before setting
the standby switch to "ON". If this is the first time you are turning on the amp, check to see if all of
the tubes are glowing.
5. Plug in the guitar cable, turn the volume knob down, and turn the standby switch on and wait a few
seconds for the bias to settle. Bring the volume up and play some tunes.
Original Sewell Amplifier Front Panel Controls
INPUT
VOLUME
TREBLE
BASS/BOOST
MASTER
Input: 1/4" standard guitar cord.
Volume: The volume is one of the most important controls on the amp. Depending on the output of
your pickups, you can find your sweet spot at various locations on the sweep. There will be a point
in which actual volume stops increasing and the tone becomes thicker and more compressed. Each
guitar will react differently and exploring this control should be a source of great enjoyment. Be
aware that settings beyond 2 o'clock will increase background noise.
Treble: The treble control is very sensitive and should be used with discretion. Like all three knobs,
there are no numbers to encourage you to set the amp with your ears. It affects the gain and
distortion of the amp and can work effectively with the bright switch to produce more mid-60's
American "scooped-mid/bell tones". Just roll back the treble to say 11 o'clock and flip on the bright
switch.
Bass/Boost: This control increases bass and gain when turned up. Note: This is not a push-pull
control.
Master: Controls the overall volume of the amplifier. The master volume is a post phase-inverter
style, and allows you to drive the preamp into distortion while maintaining low volumes. Turn it
all the way up (with the volume down) for maximum clean settings, and reverse that setting for
distortion.
Bright Switch: This switch uses a capacitor to bypass highs around the volume potentiometer. It is
only effective when the volume is set low, and increasingly fades out as the volume is increased. This
switch adds sparkle to your clean settings.
Jewel Power Indicator: Power indicator. If the jewel is lighted, the amp is on. This does not indicate
the standby setting of the amp. Note: An amplifier may be plugged in and "on", but a malfunctioning
or burnt-out indicator will not show the amp is on. Check the power cord and Power Switch if the
jewel light is not on. If these are connected correctly, then check the main fuse. If the main fuse
burns out, check for proper speaker connections. If the fuses continue to blow, the amplifier may
need servicing.
Sample Settings: For maximum clean settings, set the treble to taste, switch on the bright switch, set
the bass at noon, max the master volume and bring up the volume to about 10 o'clock. You can get
some pretty classic chimey cleans. For maximum distortion, set the volume at 2 o'clock, lower the
master volume, set the bass at about 2 o'clock, then bring up the master to the required volume level.
Rear Panel Controls
ADJUSTMENTS ONLY TO BE MADE BY QUALIFIED TECHNICIAN
Input Power
120V~60HZ
325 W
FUSE
CAUTION
ATTENTION
FUSE - 3A 250V
Type 3AG
Replace fuse only with
same type and rating.
Fuse: Blown fuses may indicate that the amplifier needs servicing. Use only the type and rating
specified on the back of the amplifier. See the section on Service Notes for proper fuse servicing
and replacement.
Power Switch: This cuts off all power to the amplifier. No filament current or tube voltages are
supplied.
Standby Switch: When this switch is in STANDBY, the amplifier tubes are effectively turned off, but
are still being warmed by the filaments if the POWER is on. Keep this switch set to STANDBY when
powering on the amplifier for at least 2 minutes to allow the tubes to warm up. This also helps
extend the life of the tubes. When set to ON, the tubes are turned on the amplifier can be used.
Always check this switch if the amp is ON but no sound is being heard.
Bias Jacks: Biasing and Tube Replacement should be performed only by a qualified technician.
Speaker Jacks: Get into the habit of checking these first. The jacks include a connection for 4, 8 and
16 ohm loads. There is an extension (EXT) jack with the 4 ohm and 8 ohm connection to connect
two 8 ohm loads if you wish. This scenario could most commonly be the use of an 8 ohm extension
speaker along with the internal speaker—connect each to the 4 ohm jacks since their combination
produces a 4 ohm load. Do not connect an 8 ohm load in the 8 ohm jack along with a 4 ohm or
16 ohm load in those jacks. This procedure halves the reflected impedance of each and will not
allow ideal operating conditions. If you are using more than one speaker, they must be the same
impedance. For example, use two 4-ohm speakers, or two 8-ohm speakers. Never use 2 different
speaker impedances - You should not mix and match. The maximum number of speakers you can
safely connect is 2. Always ensure that the speaker impedance matches the correct speaker jack,
since this amp is designed to be played "wide open". Mismatching impedances from a lower tap to
a higher speaker impedance stresses the amp more than going into a lower impedance mismatch,
and can cause arcs on the tube sockets, failure of power tubes, or even failure of the output
transformer.
Confirm that the speaker cabinet you are using matches to the correct speaker jack on the back of
the amp. For the 4 OHM and 8 OHM speaker jacks, a second cabinet may be plugged into the "EXT"
(Extension) cabinet. Note: The total speaker impedance must be determined before connecting to
the speaker jacks.
© 2009 PRS Guitars
All rights reserved.
"Paul Reed Smith," "PRS," the PRS logo, the PRS Paul Reed Smith logo, the Paul Reed Smith signature, the
bird inlays, the headstock bird, the PRS headstock shape, the PRS body shape, the PRS "scoop" design,
"Singlecut", "Mira" and the "SE" are all registered trademarks of Paul Reed Smith Guitars "Custom
24," "Modern Eagle," "SE Custom," "SC 245," "SC 250," "Starla", "Tonare", "Sewell", " Blue Sierra", and
"Angelus" are all trademarks of Paul Reed Smith Guitars. The Birds, New Birds, are copyrighted by PRS
Guitars.
TO AVOID DAMAGE, NEVER OPERATE WITHOUT PROPER SPEAKER LOAD
- RISK OF ELECTRIC SHOCK - DO NOT OPEN. No user serviceable parts inside
- RISQUE DE CHOC ÉLECTIQUE - NE PAS OUVRIR. No pièce réparable par l'utilisateur
WARNING
- TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE
AVIS
- POUR RÉDUIRE LE RISQUE D'INCENDIE OU DE CHOC ÉLECTRIQUE,
NE PAS EXPOSER CET EQUIPEMENT A LA PLUIE OU L'HUMIDIT
Advertisement
