RED SHIELD WS100G2 User Manual

Wire-free home protection system red shield ws100g2

Hide thumbs

Table Of Contents

USER GUIDE

WIRE-FREE HOME PROTECTION SYSTEM WS100G2

CONTENTS

Section 1 – Getting started

1.1 General system overview

1.2 Introduction to the system

1.3 Items included with the system

1.4 Introduction to the Smart Panel

1.5 Introduction to the Smart Panel backlight

Section 2 – Installing the Wire-free Home Protection System

2.1 Installing the Smart Panel

2.2 Powering up the Smart Panel

2.3 Understanding the battery and AC adaptor icon

Section 3 – Using the Wire-free Home Protection System

3.1 Programming your 4-digit PIN

3.2 Transmitting an emergency (Panic) alarm

3.2.1 Using the Panic alarm

3.2.2 Using the Panic alarm without activating the siren

3.3 Operating different modes

3.3.1 STANDBY mode

3.3.2 ARM mode

A. Adjusting Exit Delay

B. Adjusting Entry Delay

C. Adjusting the Alarm Duration

D. Muting the Audible Countdown

E. Arming the system

F. Disarming the system

G. Zone settings

H. Triggers in ARM mode

3.3.3 ALERT mode

A. Entering the ALERT mode

B. Exiting the ALERT mode

C. Zone settings

3.3.4 HOME mode

A. Entering the HOME mode

B. Exiting the HOME mode

C. Zone settings

Section 4 – Installing the Sensors

4.1 Introduction to the Sensors

4.2 Installing the Sensors

4.2.1 Installing the Door/Window Sensor

A. Powering up the the Door/Window Sensor

B. Installing the Door/Window Sensor

C. Mounting with the double-sided adhesive pad

4.2.2 Installing the Motion Sensor

A. Powering up the Motion Sensor

B. Installing the Motion Sensor

C. Sensor sensitivity

D. Walk test

E. Mounting using screws

4.2.3 Introduction of Key Fob Remote Control

A. Introduction

Table of Contents

Need help?

Do you have a question about the WS100G2 and is the answer not in the manual?

Questions and answers

Summary of Contents for RED SHIELD WS100G2

Page 1 2.3 Understanding the battery and AC adaptor icon Section 3 – Using the Wire-free Home Protection System 3.1 Programming your 4-digit PIN WIRE-FREE HOME PROTECTION SYSTEM WS100G2 3.2 Transmitting an emergency (Panic) alarm 3.2.1 Using the Panic alarm 3.2.2 Using the Panic alarm without activating the siren 3.3 Operating different modes...
Page 2: Section 1 - Getting Started
WARNING: Security system devices cannot compensate for loss of life or property. 1.2 Introduction to the system The Wire-free Home Protection System WS100G2 is a high quality security system combined with a range of user-friendly features. The system is controlled by a Smart Panel, which gathers information from wireless sensors placed inside and at the entry points of your home or office.
Page 3: Section 2 - Installing The Wire-Free Home Protection System Ws100G2
Function Buttons: WARNING: The Red Shield Smart Panel has a built-in tamper-proof switch to prevent the system being disabled by an intruder. When fixing the Smart Panel to a wall, first ensure that it is in Standby mode to avoid the alarm sounding.
Page 4: Section 3 - Using The Wire-Free Home Protection System Ws100G2
Fig. 1 (WS-301) Fig. 2 (WS-301) SECTION 3 – USING THE WIRE-FREE HOME PROTECTION SYSTEM WS100G2 3.1 Programming your new 4-digit PIN The Wire-free Home Protection Smart Panel is supplied with a default PIN of “1234”. This can be changed to...
Page 5: Standby Mode
New 4-digit Re-enter new PIN for - LCD display flashes with “2” Sensor Zone Status (MODE) PIN + followed by for final - Re-enter the new 4-digit PIN Door/Window Sensor confirmation - Press for final confirmation Door/Window Sensor (One beep indicates that you entered a valid PIN, two beeps indicate that an invalid operation was performed).
Page 6 E. Arming the system (1234/ Enter the default PIN “ 1 2 The Smart Panel will display the below image: On the Key Fob Remote Control: Press to ARM the system. 4-digit PIN) 3 4 ” OR your new 4-digit On the Smart Panel: First make sure the Smart Panel is in STANDBY mode, and then ARM the system by PIN for setting followed by taking the following steps:...
Page 7: Alert Mode
• On the Smart Panel: First make sure the Smart Panel is in STANDBY mode, and then enter into ALERT 4-digit PIN) Enter 4-digit PIN for setting The Smart Panel will display the below image: mode by taking the following steps: followed by Keys Description...
Page 8: Section 4 - Installing The Sensors
Press to complete the Confirm the setting and return the Smart Panel to STANDBY setting by pressing (One beep indicates that you entered a valid PIN three 3.3.4 HOME mode beeps indicate that an invalid operation was performed). There are default settings that allow the system to operate after opening the package. These settings can be adjusted to suit your individual requirements The HOME mode allows the system operate in both the Enter 4-digit PIN for setting The Smart Panel will display the below image:...
Page 9: Installing The Motion Sensor
A. Introduction - away from extreme temperature sources (radiators, ovens, stoves etc.) The Red Shield Wire-free Home Protection System Remote Control allows you to operate the systems Smart - away from direct sunlight. Panel remotely, from inside or outside the property. Using the control the system can be armed or disarmed - indoors only and not behind partitions and the siren can be activated instantly if required (using the Panic function).
Page 10 Keys Description Note Keys Description Note (1234/ You must be in STANDBY *To make sure you are in (1234/ You must be in STANDBY *To make sure you are in STANDBY mode: 4-digit PIN) mode before enrolling a STANDBY mode: 4-digit PIN) mode before deleting a - Enter the default PIN “...
Page 11: Section 5 - Troubleshooting
*Jumper: ON = Pushed in, OFF = Pulled out A.5: The Wire-free Home Protection System WS100G2 is designed for easy installation. This means that the wireless sensors are in a default setting already registered to the Smart Panel and will therefore function...
Page 12: Section 6 - General Information
5.2 Troubleshooting PIR detection range: “H”:< 15M “M”:< 6M “L”:< 4M AC power failure: House Code: 4 Jumpers This may occur if your security system is accidentally unplugged or if there has been a mains power cut. If a Zone Code: Pin header: 8 pin Power saving timer: 3 minutes...