Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for oConnor C1241-0001
- Page 1 Cine Follow Focus One C1241-0001 User Guide...
-
Page 2: Caution
Copyright © 2011 The Vitec Group plc All rights reserved throughout the world. No part of this document may be stored in a retrieval system, transmitted, copied or reproduced in any way, including, but not limited to, photocopy, photograph, magnetic or other record without the prior agreement and permission in writing from the Vitec Group plc. -
Page 3: Table Of Contents
OConnor Offices worldwide........ -
Page 4: The Cine Follow Focus One
The Cine Follow Focus One... -
Page 5: Specification
Specification Cine Follow Focus One (C1241-0001) ight (incl. main bridge, studio rod, handwheel) ... 1.83 lbs (0.83 kg) Weight of handwheel ........0.73 lbs (0.33 kg) Dimensions (WxHxD) . -
Page 6: In The Box
In the box Marking Discs (10 pack) C1241-1530 Swing Arm C1241-1200 Main Bridge C1241-1400 CFF-1 Studio Handwheel (full-size offset knob) C1241-1100 Studio Rod Bridge C1241-1300... -
Page 7: Accessories
Fujinon ENG focus 50 tooth 60 tooth C1241-1900 C1241-1800 Foam insert for Storm Case iM2200 C1241-2126 Matching OConnor accessories: Studio rod bridge C1241-1300 (depending on lens) Handwheel (for double-sided use) C1241-1100 (Cine) C1242-1100 (Photo) Handwheel extension (70 mm) C1241-1500 “Glow-in-the-dark” marking disc... - Page 8 DO NOT hang heavy items over the handwheel. Ÿ AVOID overtightening the drive gear onto the lens focus drive. Ÿ ALWAYS use genuine OConnor parts and accessories with the Cine Follow Ÿ Focus One. NEVER use solvents or oil-based cleaners to clean the Cine Follow Focus Ÿ...
-
Page 9: Components
Components index CFF-1 handwheel drive gear swing arm witness marker lock lever main bridge lock lever rod clamp lock lever studio rod bridge marking disc... -
Page 10: Repositioning The Lock Levers
repositioning the lock levers To reposition the lock levers: Pull the lock lever towards you. Slide the studio rod bridge onto the main bridge. Rotate the lock lever to the correct position. Secure the studio rod bridge using the two lock levers. Push the lock lever to secure into position. -
Page 11: Mounting The Swing Arm & Drive Gear
mounting the swing arm & drive gear Ensure that the teeth on the swing arm and main bridge interlock. Firmly hold the top of the swing arm (where the drive gear fits) whilst tightening the knurled screw. Note: The swing arm can be mounted on either side of the main bridge. -
Page 12: Mounting The Handwheel
mounting the handwheel Push the handwheel firmly into the end of the main bridge. PUSH Hold the handwheel firmly in position at the end of the main bridge and secure using the lock lever. Important note: Ensure that you can clearly see the witness marker. -
Page 13: Mounting Onto The Camera Rods
mounting onto camera rods Place the Cine Follow Focus One onto the camera rods so that the drive gear is adjacent to the lens focus drive. Secure into position using the knurled screws at the end of the studio rod bridge. The Cine Follow Focus One can be mounted from camera rods suspended above the camera. -
Page 14: Engaging The Drive Gear
engaging the drive gear Position the swing arm, so that the drive Loosen the lock lever securing the swing arm in position. gear engages with the lens focus drive. Secure the swing arm into position using the lock lever. Note: If the swing arm is mounted on the back of the main bridge, as shown, turn the lock lever clockwise to loosen the swing arm. - Page 15 Turn the handwheel. Ensure that the drive gear engages and drives the lens focus drive. Note: The drive gear can be positioned above or below the lens depending on your camera setup.
-
Page 16: Markings Discs & Witness Marker
marking discs & witness mark Set the focal distances for the Cine Follow Focus One. Using To move the witness mark: a suitable pen mark the lens focal reference points on the marking disc. The handwheel is supplied ready with a marking disc. -
Page 17: Dismounting
Dismounting Loosen the knurled screws at the end of the studio rod bridge to release the rod clamps. Loosen the lock lever on the swing arm to disengage the drive gear from the lens focus drive. Position the drive gear away from the lens and secure using the lock lever. -
Page 18: Storage
Storage Remove the drive gear from the swing arm. Loosen the lock lever securing the swing arm and fold the swing Remove the handwheel(s) by arm down onto the main bridge. loosening the lock lever at the back of the handwheel and sliding the handwheel free from the main bridge. -
Page 19: Oconnor Offices Worldwide
OConnor Offices worldwide ASIA EUROPE HEADQUARTERS CHINA FRANCE 2701 N. Ontario St. Room 706, Tower B 171 Avenue des Gr sillons é Burbank, CA 91504 Derun Building 92635 Gennevilliers CEDEX YongAn Dongli A No. 8 France Tel.: +1 818 847 8666 Jianwai Ave. - Page 20 Connor ™ itec Group brand C1241-4980/2...
Need help?
Do you have a question about the C1241-0001 and is the answer not in the manual?
Questions and answers