Table of Contents
Advertisement
ELGAR ELECTRONICS CORPORATION
9250 Brown Deer Road
San Diego, CA 92121-2294
1-800-733-5427
Tel: (858) 450-0085
Fax: (858) 458-0267
Email: sales@elgar.com
www.elgar.com
This document contains information proprietary to Elgar Electronics Corporation. The information contained herein
is not to be duplicated or transferred in any manner without prior written permission from Elgar Electronics
Corporation.
September 21, 2004
SmartWave
SmartWave
AC Power Source
AC Power Source
MODELS
SW 10500
SW 15750
SW 21000
Parallel Installation Manual
©2000 by Elgar Electronics Corporation
T M
T M
Document No. M162002-01 Rev D
Advertisement
Table of Contents
Related Manuals for Elgar SmartWave SW 15750
Summary of Contents for Elgar SmartWave SW 15750
- Page 1 ©2000 by Elgar Electronics Corporation This document contains information proprietary to Elgar Electronics Corporation. The information contained herein is not to be duplicated or transferred in any manner without prior written permission from Elgar Electronics Corporation. September 21, 2004...
- Page 3 Elgar non-warranty service rates. • Warranty field service is available on an emergency basis. Travel expenses (travel time, per diem expense, and related air fare) are the responsibility of the Buyer. A Buyer purchase order is required by Elgar prior to scheduling. •...
-
Page 4: Safety Notice
SAFETY NOTICE Before applying power to the system, verify that the SW Series unit is configured properly for the user’s particular application. WARNING! HAZARDOUS VOLTAGES IN EXCESS OF 280 VRMS, 600V PEAK MAY BE PRESENT WHEN COVERS ARE REMOVED. QUALIFIED PERSONNEL MUST USE EXTREME CAUTION WHEN SERVICING THIS EQUIPMENT. -
Page 5: Safety Symbols
SAFETY SYMBOLS CAUTION Risk of Electrical Shock CAUTION Refer to Accompanying Documents OFF (Supply) STANDBY (Supply) ON (Supply) -
Page 6: Table Of Contents
TABLE OF CONTENTS SW 10500/15750/21000 TABLE OF CONTENTS Warranty............................i Safety Notice ..........................iii Safety Symbols ...........................iv Table of Contents.........................v SECTION I – GENERAL DESCRIPTION Introduction........................1-1 Input Specifications......................1-1 Output Specifications – Normal Operation Mode ............1-1 Measurement System....................1-3 Protection and Safety....................1-4 1.5.1 Programmable Current Limit/Constant Current Ranges ......1-4 Physical Specifications ....................1-4 1.6.1 Cooling ......................1-4 SECTION 2 –... -
Page 7: List Of Figures
LIST OF FIGURES Cabinet Top View......................2-7 Cabinet Front View, SW 15750 (Slide Mounting) ........... 2-8 Cabinet Front View, SW 21000 (Slide Mounting) ........... 2-9 Cabinet Side View, SW 15750 (Slide Mounting) ..........2-10 Cabinet Side View, SW 21000 (Slide Mounting) ..........2-11 Cabinet Side View, SW 15750 (“L”... -
Page 8: Section I - General Description
SECTION 1 – GENERAL DESCRIPTION 1.1 INTRODUCTION The Elgar Models SW 10500, SW 15750, and SW 21000 provide the same high quality power source as the SW 5250A, but at higher power levels. These systems are comprised of one master chassis, one or more slave chassis, a power distribution (PDU) chassis, and an optional input power line filter (required for CE mark). - Page 9 SECTION 1–GENERAL DESCRIPTION SW 10500/15750/21000 Output Current Per Phase SW 21000: 52A to 135V in 156V range, derates linearly to 44.8A @ 156V; 26A to 270V in 312V range, derates linearly to 22.4A @ 312V. Crest Factor: 4.0 (peak output current to RMS output current) Output Frequency: DC or 40 Hz to 5 KHz.
-
Page 10: Measurement System
SW 10500/15750/21000 SECTION 1–GENERAL DESCRIPTION 1.4 MEASUREMENT SYSTEM PEAK PEAK SYSTEM RMS CURRENT POWER CURRENT CURRENT TO 135/270 TO 156/312 SW 10500 1 PHASE 156 Range 0-90A Plus Sign 0-360A Peak 0-310A Peak 0-10800W 0-10800VA 312 Range 0-45A Plus Sign 0-180A Peak 0-155A Peak 0-10800W... -
Page 11: Protection And Safety
SECTION 1–GENERAL DESCRIPTION SW 10500/15750/21000 1.5 PROTECTION AND SAFETY 1.5.1 PROGRAMMABLE CURRENT LIMIT/CONSTANT CURRENT RANGES SW 10500: X2 SW 5250 spec Currents doubled (i.e. 6.5A becomes 13A) SW 15750: X3 SW 5250 spec Currents tripled (i.e. 6.5A becomes 19.5A) SW 21000: X4 SW 5250 spec Currents quadrupled (i.e. -
Page 12: Section 2 - Installation
SECTION 2 – INSTALLATION 2.1 INTRODUCTION The Elgar Model SW 10500, SW 15750, or SW 21000 has been fully calibrated and tested prior to shipment. The system is designed to be mounted in a standard 19” RETMA cabinet. WARNING! The SW 5250S/M weighs over 126 lbs. -
Page 13: Installation
Refer to Figures 2-1 through 2-7 for information on outline and mounting dimensions. If using slides, locate the secondary mounting rail behind the front mounting rail (see Figure 2-1). Use the slides and mounting kits recommended below in Table 2-1. 24" DEEP ELGAR PN ACCURIDE JONATHAN PN ZERO-TRAK PN CABINET... -
Page 14: Input Power Requirements
SW 10500/15750/21000 SECTION 2–INSTALLATION SW 15750 CE A162001-08 Slide Kit (includes all parts listed above) SW 21000 A162001-09 Slide Kit (includes all parts listed above) SW 21000 CE A162001-10 Slide Kit (includes all parts listed above) TABLE 2-1 SLIDES AND MOUNTING BRACKETS 2.5 INPUT POWER REQUIREMENTS Input power is connected to the SW 5250M (master) and the SW 5250S (slave[s]) via the rear panel connectors. -
Page 15: Optional Sw Input Filter Wiring
SECTION 2–INSTALLATION SW 10500/15750/21000 neutral TABLE 2-2 3-PHASE INPUT POWER REQUIREMENTS WARNING! An overcurrent protection device (i.e., circuit breaker) is required in the building installation. The circuit breaker should be rated for continuous current as required by the SW system (see Table 2-2). -
Page 16: Output Connections To The Load
SW 10500/15750/21000 SECTION 2–INSTALLATION 2.6 OUTPUT CONNECTIONS TO THE LOAD Output power is located at the rear of the PDU. Refer to Figures 2-8 through 2-16. For output connections to the load, refer to Section 2.9 in the main manual. For selection of wire gauge, refer to Section 2.10 of the main manual. -
Page 17: Chassis Grounding
SECTION 2–INSTALLATION SW 10500/15750/21000 2.6.2 CHASSIS GROUNDING The master, slave(s), PDU, and optional input filter chassis should be grounded to the cabinet mounting rails using the chassis ground stud provided on each chassis. 2.7 INTERCONNECT OUTPUT POWER CABLES Output power is routed from the master and slave(s) chassis to the PDU through 5161366- 01 cable assemblies. -
Page 18: Cabinet Top View
SW 10500/15750/21000 SECTION 2–INSTALLATION CABINET REAR 26.00 MOUNTING RAIL 4.00 2PL CABINET FRONT FIGURE 2-1 CABINET TOP VIEW... -
Page 19: Cabinet Front View, Sw 15750 (Slide Mounting)
SECTION 2–INSTALLATION SW 10500/15750/21000 FIGURE 2-2 CABINET FRONT VIEW, SW 15750 (Slide Mounting) -
Page 20: Cabinet Front View, Sw 21000 (Slide Mounting)
SW 10500/15750/21000 SECTION 2–INSTALLATION FIGURE 2-3 CABINET FRONT VIEW, SW 21000 (Slide Mounting) -
Page 21: Cabinet Side View, Sw 15750 (Slide Mounting)
SECTION 2–INSTALLATION SW 10500/15750/21000 FIGURE 2-4 CABINET SIDE VIEW, SW 15750 (Slide Mounting) 2-10... -
Page 22: Cabinet Side View, Sw 21000 (Slide Mounting)
SW 10500/15750/21000 SECTION 2–INSTALLATION FIGURE 2-5 CABINET SIDE VIEW, SW 21000 (Slide Mounting) 2-11... -
Page 23: Cabinet Side View, Sw 15750 ("L" Bracket Mounting)
SECTION 2–INSTALLATION SW 10500/15750/21000 FIGURE 2-6 CABINET SIDE VIEW, SW 15750 (“L” Bracket Mounting) 2-12... -
Page 24: Cabinet Side View, Sw 21000 ("L" Bracket Mounting)
SW 10500/15750/21000 SECTION 2–INSTALLATION FIGURE 2-7 CABINET SIDE VIEW, SW 21000 (“L” Bracket Mounting) 2-13... -
Page 25: Cabinet Rear View, Sw 10500 (Slide Mounting)
SECTION 2–INSTALLATION SW 10500/15750/21000 FIGURE 2-8 CABINET REAR VIEW, SW 10500 (Slide Mounting) 2-14... -
Page 26: Cabinet Rear View, Sw 15750 (Slide Mounting)
SW 10500/15750/21000 SECTION 2–INSTALLATION FIGURE 2-9 CABINET REAR VIEW, SW 15750 (Slide Mounting) 2-15... -
Page 27: Cabinet Rear View, Sw 21000 (Slide Mounting)
SECTION 2–INSTALLATION SW 10500/15750/21000 FIGURE 2-10 CABINET REAR VIEW, SW 21000 (Slide Mounting, No Input Line Filter) 2-16... -
Page 28: Wiring For Sw 10500: 3-Phase Load
SW 10500/15750/21000 SECTION 2–INSTALLATION SHIELD SHIELD MASTER SENSE SHIELD SHIELD SHIELD SLAVE 1 LOADS SENSE SHIELD SYSTEM GROUND POWER OUT MASTER SLAVE 1 SLAVE 2 SLAVE 3 OPTIONAL INPUT FILTER (REQD FOR CE) 115/230V IN (SELECTABLE) POWER IN FIGURE 2-11 WIRING FOR SW 10500: 3-PHASE LOAD 2-17... -
Page 29: Wiring For Sw 10500: 1-Phase Load
SECTION 2–INSTALLATION SW 10500/15750/21000 SHIELD SHIELD MASTER SENSE SHIELD LOAD SHIELD SHIELD SLAVE 1 SHIELD SENSE SYSTEM GROUND A B C N POWER OUT MASTER SLAVE 1 SLAVE 2 SLAVE 3 OPTIONAL INPUT FILTER (REQD FOR CE) 115/230V IN (SELECTABLE) POWER IN FIGURE 2-12 WIRING FOR SW 10500: 1-PHASE LOAD 2-18... -
Page 30: Wiring For Sw 15750: 3-Phase Load
SW 10500/15750/21000 SECTION 2–INSTALLATION SHIELD SHIELD MASTER SENSE SHIELD SHIELD SHIELD SLAVE 1 LOADS SENSE SHIELD SYSTEM SHIELD SHIELD SLAVE 2 GROUND A B C POWER OUT MASTER SENSE SLAVE 1 SLAVE 2 SLAVE 3 OPTIONAL INPUT FILTER (REQD FOR CE) 115/230V IN (SELECTABLE) POWER IN... -
Page 31: Wiring For Sw 15750: 1-Phase Load
SECTION 2–INSTALLATION SW 10500/15750/21000 SHIELD SHIELD MASTER SENSE LOAD SHIELD SHIELD SHIELD SLAVE 1 SHIELD SENSE SYSTEM SHIELD SHIELD GROUND SLAVE 2 POWER OUT MASTER SENSE SLAVE 1 SLAVE 2 SLAVE 3 OPTIONAL INPUT FILTER (REQD FOR CE) 115/230V IN (SELECTABLE) POWER IN FIGURE 2-14 WIRING FOR SW 15750: 1-PHASE LOAD... -
Page 32: Wiring For Sw 21000: 3-Phase Load
SW 10500/15750/21000 SECTION 2–INSTALLATION SHIELD SHIELD MASTER SENSE SHIELD SHIELD SHIELD SLAVE 1 L O A D S SENSE SHIELD SYSTEM G R O U N D SHIELD SHIELD SLAVE 2 POWER OUT MASTER SLAVE 1 SENSE SLAVE 2 SLAVE 3 SHIELD SHIELD SLAVE 3... -
Page 33: Wiring For Sw 21000: 1-Phase Load
SECTION 2–INSTALLATION SW 10500/15750/21000 SHIELD SHIELD MASTER SENSE L O A D SHIELD SHIELD SHIELD SLAVE 1 SHIELD SENSE SYSTEM SHIELD SHIELD G R O U N D SLAVE 2 POWER OUT MASTER SENSE SLAVE 1 SLAVE 2 SLAVE 3 SHIELD SHIELD SLAVE 3... -
Page 34: Section 3 - Operation
SECTION 3 – OPERATION 3.1 INTRODUCTION Operating procedures for the SW 10500, SW 15750, and SW 21000 are identical to those for the standard SW 5250A; the only difference is the VA capacity of the SW 10500, SW 15750, and SW 21000 is two, three, and four times greater (respectively) than for the SW 5250A. - Page 35 SECTION 3–OPERATION SW 10500/15750/21000 This page intentionally left blank.
Need help?
Do you have a question about the SmartWave SW 15750 and is the answer not in the manual?
Questions and answers