Table of Contents
Advertisement
Quick Links
About KeypadLinc's Certification
KeypadLinc has been thoroughly tested by ITS ETL SEMKO, a nationally
recognized independent third-party testing laboratory. Products bearing
North American ETL Listed mark signifies that the product has been
tested to and has met the requirements of a widely recognized
consensus of U.S and Canadian product safety standards, that the
manufacturing site has been audited, and that the manufacturer has
agreed to a program of quarterly factory follow-up inspections to verify
continued conformance.
Smarthome Limited Warranty
Smarthome warrants to the original consumer purchaser of this product that, for a period of two years
from the date of purchase, this product will be free from defects in material and workmanship and will
perform in substantial conformity to the description of the product in this Owner's Manual. This warranty
shall not apply to defects or errors caused by misuse or neglect.
If the product is found to be defective in material or workmanship or if the product does not perform as
warranted above during the warranty period, Smarthome will either repair it, replace it or refund the
purchase price, at its option, upon receipt of the product at the address below, postage prepaid, with
proof of the date of purchase and an explanation of the defect or error. The repair, replacement, or
refund that is provided for above shall be the full extent of Smarthome's liability with respect to this
product.
For repair or replacement during the warranty period, call Smarthome customer service to receive an
RA# (return authorization number), properly package the product (with the RA# clearly printed on the
outside of the package) and send the product, along with all other required materials, to:
Smarthome
ATTN: Receiving Dept.
16542 Millikan Ave
Irvine, CA 92606-5027
Limitations:
THE ABOVE WARRANTY IS IN LIEU OF AND SMARTHOME DISCLAIMS ALL OTHER WARRANTIES,
WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. ANY IMPLIED WARRANTY, INCLUDING
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, WHICH MAY NOT BE
DISCLAIMED OR SUPPLANTED AS PROVIDED ABOVE SHALL BE LIMITED TO THE ONE YEAR PERIOD OF
THE EXPRESS WARRANTY ABOVE. NO OTHER REPRESENTATION OR CLAIM OF ANY NATURE BY ANY
PERSON SHALL BE BINDING UPON SMARTHOME OR MODIFY THE TERMS OF THE ABOVE WARRANTY
AND DISCLAIMER.
IN NO EVENT SHALL SMARTHOME BE LIABLE FOR SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER
DAMAGES RESULTING FROM THE POSSESSION OR USE OF THIS PRODUCT, INCLUDING WITHOUT
LIMITATION DAMAGE TO PROPERTY AND, TO THE EXTENT PERMITTED BY LAW, PERSONAL INJURY, EVEN
IF SMARTHOME KNEW OR SHOULD HAVE KNOWN OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts and/or the exclusion or
limitation of damages, in which case the above limitations and/or exclusions may not apply to you. You
may also have other legal rights, which may vary from state to state.
ControLinc, TesterLinc, SignaLinc, LampLinc, ToggleLinc, BoosterLinc, ApplianceLinc, KeypadLinc, FilterLinc,
ProbeLinc, SwitchLinc, TempLinc, IR Linc & SmarthomeLive are trademarked by Smarthome, Inc.
© Copyright 2003 Smarthome, 16542 Millikan Ave., Irvine, CA 92606-5027
800.SMART.HOME - 949.221.9200- www.smarthome.com
rev 112603
KeypadLinc
Wall-Mounted X10 Controller
Wall-Mounted X10 Controller with Integrated Dimmer
For models:
#12063W & #12064W
Controller only
#12073W & #12074W
with Dimmer and Amber LEDs
#12073WB & #12074WB
with Dimmer and Blue LEDs
#12073WW & #12074WW
with Dimmer and White LEDs
TM
Advertisement
Table of Contents
Related Manuals for Smarthome 12063W
Summary of Contents for Smarthome 12063W
- Page 1 The repair, replacement, or refund that is provided for above shall be the full extent of Smarthome's liability with respect to this product.
- Page 2 • User-adjustable dimming Ramp Rate and On-Level Mounts in single or multiple-ganged J-box • Programs and behaves like other Smarthome 2-Way products Invest in better Home • Responds to 64 scene addresses, each with different ramp rates and dimming...
-
Page 3: Glossary Of Terms
Glossary of Terms CAUTION!! PLC- Power Line Control- A control signal that is embedded onto the electricity Read and understand these instructions before installing! This device lines. X10 signals are a form of PLC signals. is intended for installation in accordance with the National Electric Code X10 Address- The Address part of a PLC signal contains the House and Unit code. -
Page 4: Installation Instructions
Look for sources of electrical noise. Turn off motor- The keypad is detecting load does not ized devices, dimmers, & fluorescent lights. When the any questions, consult an electrician or contact Smarthome's Tech Support electrical noise. respond. noise clears, the KeypadLinc will send the signal. -
Page 5: Helpful Tools
If you see a 10% or greater change, use a filter on that KeypadLinc’s Status LED/ Set Button top until it is even with the front plastic device. Smarthome has three units to choose from: trim ring. Once the Set Button is pressed in, power will be supplied to the KeypadLinc. - Page 6 Important: If you plan on sending status request signals to the integrated dimmer of KeypadLincs or any 2-way Smarthome product, make sure that each is programmed with a different primary address. Otherwise, their simultaneous responses to a status request may collide with one another.
- Page 7 Assigning a Button to the integrated dimmer (optional) Once the integrated dimmer has been assigned a primary address, it needs to be assigned to one or two of the control buttons on the KeypadLinc. 1. Push and hold ANY 2 buttons for at least 5 seconds. When all of the lights under the buttons begin blinking, release the 2 buttons.
- Page 8 PLC signals from being 30.0 210.0 absorbed and raise the signal strength of the entire home. 32.0 240.0 Smarthome has many filters that will fix the problem. An 270.0 34.0 average home will need between three and five filters. If you 38.5 300.0...
-
Page 9: Factory Reset
ApplianceLincs and LampLinc modules. The scenes for all these in a scene or modules can be setup simultaneously using the same make a mistake, programming sequence. Signals transmitted by Smarthome 2- you can just re- enroll that Way module will be received and understood by the KeypadLinc's... -
Page 10: Setting Up Groups
Setting Up Groups Removing the integrated dimmer from a Scene: 1. Transmit the “clear” sequence: Buttons can be programmed in Groups, which allow the indicator lights under the button to be illuminated when the button is pressed. When another button in that Group is pressed, the KeypadLinc sends the programmed signal, turns off the light 2. - Page 11 KeypadLinc will be ready to use. Address & Command (A-1, A-ON) 6. The Smarthome scene-enabled units that were enrolled in that scene will One Address momentarily blink their lights (if they are still on).
- Page 12 Investing in a X10 Maxi-Controller, (Smarthome #4020), will 5. Send the one or two X10 units or commands you want programmed into this provide access to all five button modes.