Summary of Contents for Lenoxx TL100
- Page 1 USER MANUAL 18V CORDLESS POLE SAW Model : TL100 Read the instructions thoroughly before operating the tool and keep this manual for future reference! MADE IN CHINA...
-
Page 2: Explanation Of Symbols On Your Product
Explanation of Symbols on your product Do not use unit when raining or allow it to become wet Read this manual thoroughly, before you use Read the user manual before using the device Always wear a helmet, goggles and ear protection Risk of fatal electric shock! Keep at least 10m distance from overhead lines DANGER：... -
Page 3: Safety Instructions
SAFETY INSTRUCTIONS WARNING: Read all safety warnings and all instructions. Failure to follow the safety warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or Battery-operated power tool. - Page 4 d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
-
Page 5: Pole Saw Trimming Precautions
additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. 6) Service a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. 7) Storage a) Use of transport guard during transport and storage. - Page 6 Keep other persons away from cutting end of pole saw and at a safe distance from work area. Do not use pole saw near cable, electric power or telephone lines. Maintain a minimum clearance of 3 metres (10 feet) from all power lines. CHARGING THE BATTERY (Fig.1) The battery pack is not fully charged at the factory.
-
Page 7: Important Charging Notes
40.5°C(105 °F) • If the receptacle and temperature are OK, and you do not get proper charging contact Lenoxx Electronics on 1300 666 848 5. The battery pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. -
Page 8: Pole Saw Assembly
POLE SAW INFORMATION OPERATION Fig.2 1. Insert/remove the battery pack (See Fig.2) •Always release the On/Off switch (2) before insertion or removal of the battery pack. •To remove the battery pack, withdraw it from the tool while pulling the Battery Release Button (3) down. - Page 9 Fig.3 3. Turn the locking knob in the “LOCK” direction. (IMPORTANT: Ensure that the locking knob is secured tightly.) (See Fig.4) Fig.4 4. Buckle strap (See Fig.5) You can choose to use the machine with or without the buckle strap. Fig.5 5.
-
Page 10: Saw Chain Tension
Fig.6 6. Slide battery into main handle until release button “snap” together. (Note: Fully charge the battery before first use.) (See Fig.7) Fig.7 SAW CHAIN TENSION WARNING: Remove battery pack from pole saw before servicing. Severe injury or death could occur from body contact with moving chain. WARNING: Cutting edges on chain are sharp. -
Page 11: Saw Chain Tension Adjustment
of operation. Allow chain to cool down. Follow steps below to check saw chain tension.) 1. Remove battery pack from pole saw. 2. Place pole saw on a firm surface to check chain tension. 3. Pull chain with light force 3mm (1/8") away from bottom of guide bar and release (See Fig 8). -
Page 12: Cutting With The Pole Saw
3. Wearing protective gloves pull down on chain to check chain tension 4. Do not over-tension chain. Over-tensioning will cause excessive wear and will reduce the life of the guide bar and chain. Over-tensioning also reduces the amount of cuts per battery charge. - Page 13 place to avoid possible bouncing or skating (sideways movement) of saw. 7. Remove pole saw from a cut with saw running at full speed. Stop pole saw by releasing trigger. Make sure chain has stopped before setting pole saw down. CLEANING AND MAINTENANCE CLEANING SAW BODY Keep saw body clean.
-
Page 14: Sharpening Saw Chain
Fig.14 SHARPENING SAW CHAIN Keep chain sharp. Your saw will cut faster and more safely. A dull chain will cause undue sprocket, guide bar, chain, and motor wear. If you must force chain into wood and cutting creates only sawdust with few large chips, chain is dull. Items Needed to Sharpen Chain Purchase these items from your local dealer, hardware store, or pole saw supplies outlet. - Page 15 Note: This illustration shows file guide placement and filing direction for sharpening cutters on left side of chain. 4. Hold file guide level. Make sure 30° mark on file guide is parallel to center of guide bar (see Fig.16). This will ensure that you file the cutters at 30° angle. 5.
-
Page 16: Replacing Saw Chain
REPLACING SAW CHAIN IMPORTANT: Do not clamp chainsaw in vise to replace saw chain or guide bar. Replace chain when cutters are too worn to re-sharpen or when the chain breaks. Only use replacement chain noted in this manual. Always include a new drive sprocket when replacing the chain. - Page 17 Fig.20 STORAGE If storing saw for more than 30 days, follow steps below. 1. Remove battery from chain saw. 2. Charge battery completely. (Note: It could take up to 7 hours to completely charge the battery.) 3. When battery is completely charged, remove from charger and put protective cap on battery terminals.
-
Page 18: Warranty Card
Warranty Card This warranty is in addition to other rights and remedies of the consumer under a law in relation to the goods or services to which the warranty relates. “Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
Need help?
Do you have a question about the TL100 and is the answer not in the manual?
Questions and answers