Related Manuals for OEM PS-12
Summary of Contents for OEM PS-12
-
Page 1: Owners Manual
PS-12 OWNERS MANUAL 300 Watt Powered Subwoofer 12” E X T R A L O N G –T H R O W Heavy Duty Woofer F R E E - S T A N D I N G P O W E R E D S U B W O O F E R... -
Page 2: I M P O R T A N T S A F E T Y I N S T R U C T I O N S
“dangerous voltage “ within the product’s en- (servicing) instructions in the literature accompa- closure that may be of sufficient magnitude to nying the product. constitute a risk of electric shock to persons. PS-12 O W N E R ’ S M A N U A L... -
Page 3: Table Of Contents
This will ensure that you have a complete understanding of how to setup and operate your subwoofer properly for optimum performance. Thank you again for choosing the PS-12, and we hope that you enjoy the enhanced dimension that a fine subwoofer adds to the sonic experience. -
Page 4: A T T A C H I N G T H E F E E T
DO NOT try to slide your subwoofer with the feet installed. This will damage the foot supports or the feet. If the PS-12 is placed on carpet, the spikes are likely the best choice since they will penetrate the carpet and provide a solid and stable footing for the subwoofer. -
Page 5: C O N N E C T I O N
C O N N E C T I O N No signal connection cable is provided with the PS-12 subwoofer since the type and length of cable is installation specific. A shielded RCA type coaxial cable, a shielded two-conductor wire with RCA type connectors, or a 2-channel speaker cable is required for connection of the PS-12 to the audio system. - Page 6 Use care to ensure that the proper polarity is observed (R+ is connected to R+ of PS-12, R- is connected to R- of PS-12, etc). Failure to do so will result in little to no subwoofer output or erratic output.
- Page 7 SUR. FRONT SURROUND. WOOFER BACK Line Level Line Level input input Speaker Level Input Left/ Left/ Right Right Right Left OPTION 1 OPTION 2 OPTION 3 PS-12 O W N E R ’ S M A N U A L...
-
Page 8: S E T U
In many cases the designated location may already be chosen and the only available adjustments may be the subwoofer’s controls. The PS-12 controls will allow you to make the best of virtually any installation. If you feel uncomfortable with setting up your PS-12 after reading through this section then you should consider enlisting the help of an experienced person or contacting your dealer. -
Page 9: Ps-12 Controls
S E T U P (continued) PS-12 Controls The PS-12 subwoofer has thee variable controls for tailoring its output to the room and to the primary speakers (also known as satellites). These controls are Level, Crossover Frequency, and Phase. The control with the most audible effect is the Level control, followed by the Crossover Frequency, and then the Phase control, which has the least audible effect. -
Page 10: S P E C I F I C A T I O N
The PS-12 contains a circuit that automatically powers up the amplifier when a signal is detected. The same circuit also places the PS-12 into standby mode when no signal has been detected for a period of approximately 10 minutes. This signal sensing circuit can be bypassed by switching the Auto switch the OFF position if it is preferable to control the PS-12’s power with a remotely operated power source. -
Page 11: N O T E S
N O T E S PS-12 O W N E R ’ S M A N U A L... - Page 12 OEM SYSTEMS COMPANY Sparks, Nevada (775) 355-0405 (800) 291-0561 FAX www.oemsystems.com info@oemsystems.com Rev. F...
Need help?
Do you have a question about the PS-12 and is the answer not in the manual?
Questions and answers