1.LCD Monitor Installation 1-1 Installation: (1) The following process offers users the best way to set up your LCD Monitor into a whole PC system with correct and safe installation. (2) Turn off the power switch of the PC and disconnect from the mains input supply.
Page 3
2.Function Keys and operation: 2.1 Function Keys Definition and description: (1) Menu Key: Use this key to select and execute the magnitude and function process. The Sequence flows of Manu Key pressing: (a) Mode Selection: (+ Key) Press Manu key Display 1 press 2 press press...
Page 4
(2) + Key: (a) In the Mode-Selection Mode: Pressing this key to locate forward the icon you want to adjust. Pressing it once, it moves one step forward to the next icon. Pressing it twice, it moves forward one more step to next 2nd icon. And so on. (b) Keep pressing down on this key, it flows continually through every icon and stops at the icon when the key is released.
Page 5
(f) Keep pressing down on this key, and it will keep increasing continually until the key is released. Switch¡ G Power on/off Switch. Press this Key once; the monitor would be turned on. Press this key again and the monitor will be turned off. Users are reminded that prior to press this Key to turn on the monitor, remember to switch on your PC first Version:1.0...
Page 6
2-2. Quick OSD Adjustment & Execution Operation: Key to be pressed Menu Display Remark Step 1 OSD Display Menu Key OSD Menu shows up. 1."Colour Icon” keeps flashing. 2.Mode is ready for Colour Adjustment. 3. Resolution displayed Press/Display: Colour Adjusting Mode Section 1 + key: 1 press...
Page 7
Section 1 : Colour Mode Adjustment Key to be pressed Menu Display Magnitude Range Step 1 Example: Contrast Contrast: 0~255 Brightness: 0~216 Red Gain: 0~255 Menu Key Green Gain: 0~255 Blue Gain: 0~255 Contrast Brightness/ Red/Green/ Blue by 1. “Colour icon” keeps flashing. “+ key”...
Page 8
Step 4 Example: Contrast Menu Key The Contrast adjustment is completed. The system is ready for next selection 1. “Colour icon” keeps flashing. “Contrast” marked by indigo light. Step 5 Example: Brightness If selects: Red, Green, Blue. Repeat step 3~ 5 to +/- key complete the adjustment.
Page 9
Step 7 Example: Brightness * Keeps press the “+ key”: Value in the Scale is increasing until 216 * Keeps press +/-key the “- key”: Value in the Scale is decreasing until 0 Release the key, the value will stop at 1.
Page 10
Step 10 Example: Exit Manu key System backs to Mode Selection Status and is ready to select: 1. “Colour icon” keeps flashing. Step 11 +/-key Section 2 or Section 3 or Section 4 or Section 5 or Section 6 The selected icon become flashing. Version:1.0...
Page 11
Section 2: Image Mode Adjustment Key to be pressed Menu Display Magnitude Range Step 1 Example: H-Position H-Position: 0~146 V-Position: 0~20 Sharpness: 1/2/3/4/5 Menu Key Phase: 0~31 Clock: 0~127 H-Position V-Position/ Sharpness/ Phase/Clock 3. “Image icon” keeps flashing. by “+ key” 4.
Page 12
Step 4 Example: H-Position Menu Key H-Position adjustment is completed. The system is ready for next selection 3. “Image icon” keeps flashing. “H-Posit.” marked by indigo light. Step 5 Example: V-Position If selects: Sharpness, Phase, or Clock: +/- key Repeat step 3~ 5 to complete the To select adjustment.
Page 13
Step 7 Example: V-Position * Keeps pressing “+ key”: Value in the Scale is increasing until 20 * Keeps pressing +/- key “- key”: Value in the Scale is decreasing until 0 Release the key, the value will stop at 3.
Page 14
Step 10 Example: Exit Manu key System backs to Mode Selection Status and is ready to select: 1. “Image icon” keeps flashing. Step 11 +/-key Section 1 or Section 3 or Section 4 or Section 5 or Section 6 The selected icon become flashing. Version:1.0...
Page 15
Section 3: Function Execution Key to be pressed Menu Display Remark Step 1 Example: Auto Configuration Manu pressed and Display: Auto Config. Menu Key Selected by +/- key: Auto Position. Auto config Auto Phase. Auto Clock. Auto Balance. Exit 5. “Function icon” keeps flashing. 6.
Page 16
Step 4 Example: Auto Configuration Menu Key Auto Config. is completed. The system is ready for next selection “Function icon” keeps flashing. Step 5 Example: Auto-Position If selects: Auto Phase, Auto Clock or Auto +/- key Balance: Repeat step 3~ 5 to To select execute.
Page 17
Step 7 Example: Auto-Position * Presses “+ key” to select “Yes.” * Presses “- key” to select “No.” +/- key “Function icon” keeps flashing. Step 8 Example: Auto-Position Manu key Auto-Position execution is completed. The system is ready for next selection “Function icon”...
Page 18
Step 10 Example: Exit Manu key System backs to Mode Selection Status and is ready to select: “Function icon” keeps flashing. Step 11 +/-key Section 1 or Section 2 or Section 4 or Section 5 or Section 6 The selected icon become flashing. Version:1.0...
Page 19
Section 4: OSD Manu Adjustment Key to be pressed Menu Display Remark Step 1 Example: Language Manu pressed and Display: Language Menu Key Selected by +/- key: OSD H-Position. Language OSD V-Position. OSD Timer. Exit 7. “OSD Manu icon” keeps flashing. 8.
Page 20
Step 4 Example: Language Menu Key Language setting is completed. The system is ready for next selection “OSD Manu icon” keeps flashing. Step 5 Example: OSD H-Position Adjusting Range: OSD Position: H-Position: 0~120 +/- key V-position: 0~ 120 To select OSD If selects: H-Position OSD V-Position.
Page 21
Step 7 Example: OSD H-Position * Keeps presses “+ key”: Value in the Scale is increasing until 120 * Keeps presses +/- key “- key”: Value in the Scale is decreasing until 0 Release the key, the value will stop at the satisfied point.
Page 22
Step 10 Example: Exit Manu key System backs to Mode Selection Status and is ready to select: “OSD Manu icon” keeps flashing. Step 11 Section 1 or Section 2 or Section 3 or Section 5 or Section 6 The selected icon become flashing. Version:1.0...
Page 23
Section 5: Function Execution Key to be pressed Menu Display Remark Step 1 Example: Input Source Manu pressed and Display: Input Source. Menu Key Selected by +/- key: Mode Option. Input Source Reset. Exit 9. “Misc icon” keeps flashing. 10. “Input Source” marked by indigo light.
Page 24
Step 4 Example: Input Source Menu Key Input Source Selection is completed. The system is ready for next “Misc icon” keeps flashing. selection. Step 5 Example: Mode Option If selects: Reset. Repeat step 3~ 5 to +/- key execute. To select Mode Option 5.
Page 25
Step 7 Example: Mode Option * Presses “+ key” to select “MAC768-75.” * Presses “- key” to select “VESA768-75” +/- key “Misc icon” keeps flashing. Step 8 Example: Mode Option Manu key Mode Option selection is completed. The system is ready for next “Misc icon”...
Page 26
Step 10 Example: Exit Manu key System backs to Mode Selection Status and is ready to select: “Misc icon” keeps flashing. Step 11 +/-key Section 1 or Section 2 or Section 3 or Section 4 or Section 6 The selected icon become flashing. Version:1.0...
Page 29
User’s Control: Power on/off, OSD control Environmental Operation Temp.: Condition: 0~50 degree C Storage Temp.: -20~60 degree C Humidity: 10~90% Accessories: Signal cable Version:1.0...
Page 30
3-2. Appendix A: Systems Compatible: Input Mode Resolution SXGA 1280 x 1024 1024 x 768 SVGA 800 x 600 640 x 480 DOS (Text) 640 x 480 DOS (EGA) 640 x 350 TEXT 720 x 400 832 x 624 NTSC 720 x 240(I) 720 x 288 (I) 3-3: Appendix B: Modes supported...