Technical Data; Scope Of Delivery; Accessories; Installation - Bell and Gossett ecocirc XL Installation, Operation And Maintenance Manual

Example: ecocirc XL B 15–75
-15
-75

3.3 Technical data

Feature Description
Motor model Electronically commutated motor with perma-
nent magnet rotor
Series ecocirc XL
Rated voltage 1 x 115 V ±10%
1 x 208–230 V ±10%
Frequency 50/60 Hz
Power consumption 100–1700 W
IP protection IP 44
Insulation class Class 155 (F)
Maximum working The maximum pressure is indicated on pump
pressure nameplate
175 PSI (12 bars)
Liquid temperature 14°F (-10°C) to 230°F (110°C)
range
Ambient temperature 32°F (0°C) to 104°F (40°C)
range
Ambient humidity 95% non-condensing
Pumping media Water and water/glycol mixtures
Sound pressure ≤ 43 dB (A)
EMC (electromagnetic EN 55014-1:2006 + A1:2009 + A2:2011, EN
compatibility) 55014-2:1997 + A1:2001 + A2:2008, EN
61000-3-2:2006 + A1:2009 + A2:2009, EN
61000-3-3:2008, 61800-3:2004+A1:2012.
Leakage current < 3.5 mA
I/O auxiliary +15 VDC Imax < 40 mA
power supply
Fault signal relay Vmax < 250 VAC
Imax < 2 A
CSA certification NSF/ANSI-372 compliant (bronze body parts)

3.4 Scope of delivery

Inside the package you will find:
• Pump unit
• Insulating shells for pump body — for heating applications
• O-ring to be used as replacement between motor housing and
pump body
• Two (2) gaskets for flanged connection
• 20 mm x ½" NPT electrical fitting
• IOM and Quick Start guide

3.5 Accessories

• Companion flanges
• Fastener Packs consisting of 4 bolts and 4 nuts (for 2–bolt models)
• Fastener Packs consisting of 8 bolts and 8 nuts (for 4–bolt models)
• Pressure sensor (for details see section 5.2.10 of this manual)
• Temperature sensor (for details see section 5.2.10 of this manual)
• Wireless module
• RS–485 module
1
The pump can be used with water/propylene glycol mixtures up to 50% with a maximum viscosity of 50cST at 14°F (-10°C). The pump has built-in overload and
thermal protection to protect the pump from overload due to increased fluid viscosity. Pump performance is based on 77°F (25°C). Therefore pumping of glycol
mixtures will affect max performance, depending on mixture concentration and temperature.
ecocirc XL Installation, Operation, and Maintenance manual
Maximum pump head (FT)
Maximum pump flow rate (GPM)
1
up to 50%.

4 Installation

Precautions
WARNING:
• Observe accident prevention regulations in force.
• Use suitable equipment and protection.
• Always refer to the local and/or national regulations,
legislation, and codes in force regarding the selection of
the installation site, plumbing, and power connections.

4.1 Pump handling

WARNING:
Observe local codes and regulations setting the limits for
manual lifting or handling.
Always lift the pump by the motor housing or pump body. If the pump
weight exceeds the manual handling limits, use lifting equipment with
lifting straps.

4.2 Tools required for pump installation

• T-Handle with allen screw
• Control screw driver – with 2 mm blade size
Model number Allen screw size (mm) T-handle length (in)
20–35 5
36–45 5
15–75 5
55–45 6
20–140 6
65–130 8
40–200 8

4.3 Facility requirements

4.3.1 Pump location

DANGER:
Do not use this unit in environments that may contain flam-
mable/explosive or chemically aggressive gases or powders.
Guidelines
Observe the following guidelines regarding the location of the prod-
uct:
4 Installation
8
8
8
10
10
12
12
5