Advertisement
Quick Links
Important
1.
To get the best operation and life from your machine, please read and comply with these instructions.
2.
Clean machine thoroughly before and after each use using cleaning instructions below.
3.
Minimize the use of alkaline cleaners as they may cause pitting and dulling of the finish.
Operation of CanPRO
1.
Set side handle #20 in the unlock position.
2.
Place can on the Table Base Can Sitter and gently lower the U-shaped pin of the Cutter Housing Assembly #41 is over the lid. Be sure
that the can is against the face of the can opener.
3.
Lock the can in place by pushing down on the Side Handle. Turn Top Handle #4 in a CLOCK-WISE direction to open can. Warning:
Over-rotating beyond the initial seam cut may cause metal slivers. Incision point may be sharp. Train operators when to stop cutting and
how to remove lid safely.
To Clean
WARNING: Cutting area must be kept clean at all times as indicated in the "CLEANING INSTRUCTIONS – USE OF BRUSH." Inspect and
clean the cutter and gripper with the included brush after each use to ensure proper operation. Failure to follow the included "Cleaning
Instructions" will cause damage and VOID WARRANTY.
Disassemble for Cleaning.
1.
UNLOCK SIDE HANDLE #20. Slightly press Gripper Housing #7 face to pull out Side Locking Pin #16.
2.
Tilt back Gripper Housing #7.
3.
IMPORTANT: Pull out Cutter Housing Assembly #41 and clean with brush. Use brush provided to clean around outside of Cutter
Housing and inside the Mechanism Housing. Also use brush to clean all debris from around the Gripper.
4.
After cleaning with brush, rinse off residue. SEE SEPARATE "CLEANING INSTRUCTIONS – USE OF BRUSH" FOR LOCATIONS.
Reassemble.
5.
Insert Cutter Housing Assembly #41.
6.
Return Gripper Housing #7 to closed position.
7.
Slightly press Gripper Housing #7 face to re-insert the Side Locking Pin #16. (Ensure side handle #20 is unlocked.)
1.
56050 - ( ) CanPRO
OPERATING INSTRUCTIONS
If cleaned in DISHWASHER, disassemble and clean with brush per above instructions.
2. Proper cleaning maximizes the life of the parts.
Can Size
#2
#5
#10
Note:
Recommended Handle Turns:
Diameter
Handle Turns
3"
3 Revolutions
5"
5 Revolutions
6"
6 Revolutions
Advertisement
Summary of Contents for Nemco CanPRO 56050-()
- Page 1 56050 - ( ) CanPRO OPERATING INSTRUCTIONS Important To get the best operation and life from your machine, please read and comply with these instructions. Clean machine thoroughly before and after each use using cleaning instructions below. Minimize the use of alkaline cleaners as they may cause pitting and dulling of the finish. Operation of CanPRO Set side handle #20 in the unlock position.
- Page 2 Replacing Cutter from Cutter Housing Assembly Hold Cutter Shaft #26 with wrench and loosen Cutter Locking Bolt #31 (left hand thread) with another wrench by turning clockwise. Remove Cutter Washer #30 and Cutter Spacer #29 and Cutter #28. Replace with new Cutter. Reverse steps 2 and 1 to re-assemble.
- Page 3 The warranty provided herein shall be limited to parts and labor. Any determination that a product is defective or covered by this warranty shall be made by Nemco, in its sole discretion. The determination of whether to repair or replace a defective, covered product, or to refund the purchase price for the product, will be at Nemco's sole discretion.
- Page 4 FROM AROUND GRIPPER. USE BRUSH TO CLEAN ALL DEBRIS FROM THE INSIDE OF THE HOUSING. USE BRUSH TO CLEAN ALL DEBRIS FROM THE CUTTER. NEMCO FOOD EQUIPMENT 301 Meuse Argonne, Hicksville, OH 43526 Phone: (419) 542-7751 419) 542-6690 1-800-782-6761 Fax :(...
-
Page 5: Installation
NEMCO Food Equipment 301 Meuse Argonne Road Hicksville, OH 43526 419-452-7751 1-800-782-6761 419-542-6690 FX CanPRO Compact Model 56050-1 Basic mount Prior to Base Installation: Think about the "ideal" location for the can opener. 1. Be certain that there is enough room for the operator to comfortably and efficiently turn the handle.
Need help?
Do you have a question about the CanPRO 56050-() and is the answer not in the manual?
Questions and answers