1. Manuals
  2. Brands
  3. King Controls Manuals
  4. Marine GPS System
  5. 1200-KU
  6. Installation and operating instructions manual

King Controls 1200-KU Installation And Operating Instructions Manual

15” marine satellite system with built-in dvb for positive satellite identification
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
®
15" Marine Satellite System
with built-in DVB for positive satellite identification
Model 1200-KU
Installation and Operating Instructions
®
Satellite Solutions for Mobile Markets
11200 Hampshire Avenue South, Bloomington, MN 55438-2453
Phone: (800) 982-9920
Fax: (952) 922-8424
www.kingcontrols.com
MEMBER
20430 REV C

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 1200-KU and is the answer not in the manual?

Questions and answers

Summary of Contents for King Controls 1200-KU

  • Page 1 ® 15” Marine Satellite System with built-in DVB for positive satellite identification Model 1200-KU Installation and Operating Instructions ® Satellite Solutions for Mobile Markets 11200 Hampshire Avenue South, Bloomington, MN 55438-2453 Phone: (800) 982-9920 Fax: (952) 922-8424 www.kingcontrols.com MEMBER 20430 REV C...

  • Page 3: Table Of Contents

    The satellite TV market is expanding and changing. The information in this manual was accurate at the time of printing. If your Sea-King does not operate as outlined in this manual please call King Controls at (800) 982-9920 or visit our website at www.kingcontrols.com.

  • Page 4: Introduction

    INTRODUCTION SECTION 1 The Sea-King 1200-KU Marine Satellite System includes 2 main components (Fig. 1). Dome (Antenna) Unit Mounted on the vessel. The dish is covered by a protective dome that keeps operational components free from the elements. Controller Located in the vessel. Activates the search mode and provides limited diagnostic functions using the status light.

  • Page 5: Definition Of Terms

    DEFINITION OF TERMS SECTION 2 AZIMUTH: Circular rotation around the vessel. Using a clock as reference, the bow of the vessel is 12:00 o’clock, and the stern is 6:00 o’clock (Fig. 2). Fig. 2 ELEVATION: Angle in degrees measured from a level plane (Fig. 3). Fig.

  • Page 6: Installation

    • appropriate fasteners and tools to install all components and wiring • adhesive sealant, compatible with vessel material • #1844 King Controls Installation and Diagnostic Keypad #1844 (may be obtained from an authorized dealer or King Controls) Diagnostic Keypad KIT CONTENTS 1. Unpack and identify all components (Fig. 4).

  • Page 7: Remove Shipping Restraints

    REMOVE SHIPPING RESTRAINTS 1. Remove and save the dome cover screws. (Fig. 5). 2. Carefully remove the dome cover. Do not allow dome cover to catch on internal components or wiring. DO NOT SET THE DOME COVER UPSIDE DOWN. 3. Remove and discard the shipping bolt. Fig.

  • Page 8: Dome Location

    The dome unit requires a 16.5“ diameter mounting area on the vessel surface. You may also use an industry standard mount. (Call King Controls or visit www.kingcontrols.com for more information.) Exact hole spacing is shown at right. Distances are to centers of holes.

  • Page 9: Coax Requirements

    Fig. 7 1200-KU TYPICAL INSTALLATIONS COAX REQUIREMENTS IMPORTANT! USE ONLY THE COAX CABLE SUPPLIED WITH THE SEA-KING. COIL AND STORE EXCESS CABLE IN THE CABINET WITH THE COMPONENTS. DO NOT CUT COAX. If coax cable other than that supplied with the Sea-King is used, the following guidelines...

  • Page 10: Pre-Installation Hookup For Initial Search

    PRE-INSTALLATION HOOKUP FOR INITIAL SEARCH To verify proper operation of the components, temporarily connect the unit and perform an initial search as follows: Fig. 9 1. Place the dome unit in its mounting location and temporarily secure the unit from falling. Depending on the location, you may have to use the supplied right angle F-connectors to avoid bending the coax too sharply during the...

  • Page 11: Wiring Schematics

    Dish Network / ExpressVu / DIRECTV Fig. 10 Sea-King Model 1200-KU Single satellite (or) multi-satellite with auto-switching from master receiver only Note: HDTV receivers require HDMI or component video/audio cable connection to TV. Page 9...
  • Page 12 DIRECTV Fig. 11 Sea-King Model 1200-KU Multi-satellite with auto-switching from any receiver Note: To automatically switch between satellites using any receiver, tune all other receivers to channel 202 on the 101 satellite. IMPORTANT! Main coax cable must be connected to 18V input on multi-switch.
  • Page 13 This page intentionally left blank. Page 11...

  • Page 14: Satellite Configuration

    If you do not have a keypad, contact your local authorized King-Dome dealer or call King Controls at (800) 982-9920. The Sea-King is factory pre-set for DIRECTV standard digital programming broadcast from the 101° W satellite.
  • Page 15 SWITCHING MODE AND PROVIDER CODE CHART Service Satellites Switching Provider Mode Code DIRECTV Single Satellite 101 (Factory Preset) DIRECTV Plus 101, 119 Dish Network Single Satellite 119 Dish 500 (SW21 Switch) 110, 119 Dish 1000 (SW64 Switch) 110, 119, 129 Dish 1000a (SW64 Switch) 61, 110, 119 Bell ExpressVu...
  • Page 16 SATELLITE SERVICE OPTIONS DIRECTV Single Satellite 101 Receive programming from the DIRECTV 101 satellite only. DIRECTV Plus: 101, 119 Automatically switch between the 101 and 119 satellites for DIRECTV. IMPORTANT: This Sea-King will not receive channels broadcast from DIRECTV’s Ka band satellites at 99° and 103°.
  • Page 17 SATELLITE SERVICE OPTIONS DISH NETWORK Single Satellite 119 Receive programming from the 119 satellite only. Dish 500 Automatically switch between the 110 and 119 satellites for Dish Network by using the receiver’s remote control. Dish 1000/1000a Dish Network HD programming is broadcast from 4 satellites (61,110,119,129). The 61 and 129 satellites broadcast identical programming.
  • Page 18 Perform the programming on these two pages using the codes you determined from the chart on page 13 (EXCEPT DIRECTV 101 SERVICE - see page 12). SET SATELLITE SWITCHING MODE 1. The Diagnostic Keypad should be plugged in (page 8). If not, unplug the controller and plug in the Keypad.
  • Page 19 SET SATELLITE PROVIDER CODE * 24 # 1. Press to display the current service provider. * 96 # 2. To change the current service provider, press * 66 # * 88 # 3. Press the UP and DOWN arrows (2 and 8 keys) to choose the desired service provider. * 25 # 4.
  • Page 20 IMPORTANT: YOU MUST PROGRAM IN YOUR CURRENT ELEVATION ZONE EVEN IF YOU DO NOT CHANGE YOUR SWITCHING MODE OR PROVIDER CODE. DIRECTV: SET ELEVATION ZONE AND PERFORM INITIAL SEARCH 1. Determine your elevation zone from the map on page 19. 2.
  • Page 21 Page 19...

  • Page 22: Dish Network - Expressvu Check Switch Procedure

    THE DOME UNIT MUST BE ON THE GROUND, DOCK, OR MOTIONLESS PLATFORM WITH NO MOVEMENT. For automatic satellite switching, King Controls recommends using a Dish Network model 311 receiver for Dish 500, and a Dish Network model VIP211 or a VIP211k HDTV receiver for Dish 1000/1000a.
  • Page 23 5. When test is complete, a screen similar to DISH 119 and EXPRESSVU 91 one of the following should appear: (Screen graphics may vary.) NO SWITCH DETECTED INSTALLED DEVICE UNKNOWN DISH 500 EXPRESSVU HDTV 82/91 MUST SHOW “SW21” NO “X”s DISH 1000 DISH 1000a NO “X”s...

  • Page 24: Dome Installation And External Wiring

    When configuration and search are successfully completed, disconnect the unit as follows: a) Turn power off at the keypad. b) Turn power off at the receiver. c) Disconnect power. d) Disconnect coax. DOME INSTALLATION AND EXTERNAL WIRING Fig. 13 1. Apply foam gasket to bottom of dome unit (Fig. 13). Note: The Sea-King is wired for multiple receiver support.
  • Page 25 Fig. 14 IMPORTANT! Use right angle F-connector ONLY IF ROUTING COAX TO THE SIDE with a direct to deck installation method. Fill ends of F-connectors with grease. IMPORTANT! You must fill the ends of ALL external coax with the supplied dielectric grease. Failure to do so will void warranty.

  • Page 26: Internal Wiring

    INTERNAL WIRING 1. Refer back to your desired wiring configuration and make all permanent connections as shown, keeping in mind the following important points: a) For the permanent installation, use the Wall Mount Controller, not the keypad. b) The connection between the dome unit and the receiver must be a direct connection with no devices in between.
  • Page 27 This page intentionally left blank. Page 25...

  • Page 28: Operation

    This Sea-King will not receive channels broadcast from DIRECTV’s Ka band satellites at 99° and 103°. Satellite TV and receiver technology are constantly changing. If you experience difficulty go to www.kingcontrols.com or contact the King Controls Service Department at (800) 982-9920, ext. 373. 1. Turn on TV and Receiver.
  • Page 29 AUTOMATIC SATELLITE SWITCHING 1. Simply choose your desired channel using the receiver’s remote control. The Sea-King will automatically switch to the appropriate satellite. Note: For better performance when using the automatic satellite switching feature, change channels by selecting your program from the channel guide rather than channel surfing. It is common for the picture to pixel or display an error message when the antenna is switching between satellites, the vessel is pitching or rolling excessively, or the signal has been temporarily blocked.

  • Page 30: Troubleshooting

    Did not initiate alternate search method Hold ON/SEARCH button for 3 correctly. FULL SECONDS. (See OPERATIONS, page 26.) Call King Controls. STATUS light flashes orange. Before search: bad coax connection. Move vessel to have unobstructed After unsuccessful search view of southern sky.
  • Page 31 CHOOSING A NEW ZONE USING THE WALL MOUNT SWITCH Note: Choose a new zone only if you have traveled a significant distance and are unable to acquire the satellite IMPORTANT! You must complete step 3 within 5 seconds of step 2. 1.

  • Page 32: Maintenance

    This loss of signal is commonly referred to as “rain fade” and is caused by the combination of water in the atmosphere and water on the dome surface. To minimize this issue and eliminate the effects of water on the dome, apply King Controls ®...

  • Page 33: Limited Warranty

    This warranty does not apply where: • The product has been abused, misused, improperly installed or improperly maintained. • Repairs have been made or attempted by others that are not certified by King Controls to do such repairs. • Repairs are required because of normal wear and tear.
  • Page 34 Notes: Page 32...
  • Page 36 ® 11200 Hampshire Avenue South, Bloomington, MN 55438-2453 Phone: (800) 982-9920 Fax: (952) 922-8424 www.kingcontrols.com...

Table of Contents