Advertisement
Quick Links
Advertisement
Summary of Contents for Centro Theatre Set 2
- Page 1 Centro Theatre Set 2 Assembly Instructions...
- Page 3 Align acrylic cap notches Fully join posts and tighten Stand base assembly on the in upper 8-way post remaining grub screws to ground. Loosen grub screws assembly with protruding make assembly secure. and slide both connector bars connectors at stage 1. Repeat for other base post.
- Page 4 4.2.1 4.2.2 4.2.3 The horizontal (H, H1 and H2) and vertical (V and V1) frame profiles are joined in a similar manner to the posts 4.1) Loosen grub screws and slide connector bars halfway out of the channel. 4.2) Join profiles ensuring graphic fixing strips are aligned and the expanding clamps are at either end of the assembled profiles.
- Page 5 4.2i 4.2ii 4.2i) Centre vertical ‘V1’ differs due to the presence of twin graphic fixing strips. 4.2ii) Bottom horizontal ‘H2’ differs with the introduction of the adjustable thumb screw foot in the centre. 4.3) Tighten grub screws to make secure.
- Page 6 Connect two vertical (V) 1531mm assembly rails at 90º to each end of the 1500mm horizontal rail (H2) ensuring that the graphic fixing strip is outermost and the verticals are flush with the end of the 1500mm rail. Bottom horizontal 1500mm rail (H2) should have an adjustable thumbscrew foot in the middle of a 260mm connector bar.
- Page 7 Connect second horizontal 1500mm rail assembly (H), using the expanding clamps, to top of assembled verticals (V, V1 and V) ensuring that the graphic fixing strip is at the bottom. Tighten grub screws on vertical rails to secure. This completes the bottom section of the framework.
- Page 8 For the top section of the framework, connect the two 220mm profiles, with expanding clamps at both ends and the single fixing strip, at 90º flush to each end of the third 1500mm horizontal rail (H). Ensure that the graphic fixing strip on the verticals are outermost and the graphic fixing strip on the horizontal 1500mm rail is at the top.
- Page 9 Slot final top horizontal 1500mm rail assembly (H1) to the 220mm verticals, ensuring that the graphic fixing strip is at the top. Tighten grub screws on verticals to secure framework. This completes the top section of the framework.
- Page 10 Slot the bottom section framework into the channel of the assembled post at 90º to the base plate. Ensure framework is equidistant from the base plate, adjustable foot rests on the ground, and graphic fixing strip is adjacent to the floor. Tighten both grub screws in the horizontals (H2 and H) to secure.
- Page 11 10.1 10.2 Slot open end of framework into other assembled post, at 90º to the base plate. Ensure bottom section is equidistant from the floor at both ends and the adjustable foot rests on the floor. Tighten remaining grub screws in horizontals (H2 and H) to secure bottom section framework to both post assemblies.
- Page 12 11.1 11.2 Affix the top section framework into the same channel as the bottom section ensuring graphic fixing strips are all on the same side of the system. Leave a gap of 60mm in between bottom and top framework assemblies and tighten all grub screws in horizontals (H and H1) to secure to post.
- Page 13 12.1 12.2 Prepare and cut aperture in graphic according to the graphic spec appropriate Unpack the LCD/Plasma to the desired screen size. Screen Mounting Bracket, 4 off Apply magnetic tape to 260mm connector bars, and 4 rear of graphic panels in suitable screws and washers locations shown on graphic to thread into connector bars.
- Page 14 14.1 14.2 14.3 14.4 Insert 2 screws through upper corner mount holes as shown and clearance holes in 2 off connector bars. Position mount centrally over upper horizontal rail in aperture and screw (not fully) into other 2 off 260mm connector bars, situated on the other side of the horizontal rail, to hold in position.
- Page 15 15.1 15.2 15.3 Raise screen mount so bottom holes are above the lower horizontal rail in aperture. Insert remaining 2 screws through lower mount holes (4 openings from either end of the screen mount) and clearance holes in 2 off 260mm connector bars adjacent to mount.
- Page 16 16.1 16.2 Align other 2 off 260mm connector bars, located behind horizontal rails, and screw into threaded holes. Ensure bottom screws rest on lower horizontal rail, mount is in centre of aperture, and tighten all 4 screws to secure assembly.
- Page 17 With the elongated holes Position screen centrally on the mounting arms above bracket and lower until uppermost, align arms top of both mounting arms centrally with 4 off fixing hook over mount. points on rear of screen equidistant from the top. Insert 4 off screws with suitable washers and tighten.
- Page 18 19.1 19.2 Slide locking bar between the mounting arms and the plasma mounting bracket if desired. For extra security, there is a facility to add a padlock to the locking bar.
- Page 19 To complete Centro Theatre Set 2 display, please affix podium table to the front of one of the posts.