Summary of Contents for HANGIL CONTROL HCT-2216
-
Page 1: Remote Controller
REMOTE CONTROLLER Digital Remote Control System Digital Remote Control System USER’S MANUAL USER S MANUAL HCT-2216 / HCR-2216 HANGIL CONTROL Co., Ltd. Hangil Control Co., Ltd 2008-09-24... -
Page 2: Table Of Contents
4 SPECIFICATIONS AND DRAWING 4. SPECIFICATIONS AND DRAWING -------------- 5. INSTALLATION AND SETUP ------------------ 6. OPERATING PROCESS ---------------------- 7. OPERATING FLOWCHART ------------------- 8. MAINTENANCE ---------------------------- 9. TROUBLESHO OTING GUIDE ------------------ 10. CHARGER AND BATTERY ------------------ Hangil Control Co., Ltd 2008-09-24... -
Page 3: Introduction
4,096 Electronic K e y Code Numbers to prevent any electronic interferences. 2-6. Enough Distance for Operation The operating distance of transmitter is 70 meters which is eno ugh to operate and be in safe operation. Hangil Control Co., Ltd 2008-09-24... -
Page 4: Configurations
3. CONFIGURATIONS 3 1 Basic Parts 3-1. Basic Parts Transmitter (HCT-2216) ----------------------------- - 1 SET Receiver (HCR-2216) ---- --------------------------- - 1 SET Receivin g Antenna (f or 173MHz ) ----------------------- - 1 EA Char g er (HCG-4814) -------------------------------- - 1 EA... -
Page 5: Specifications And Drawing
-30 ¡ Æ C ~ + 7 0 ¡ Æ C WEIGHT (GROSS) 750g 5.90kg INPUT POWER DC4.8 V ( PAC K ) AC85 V ~ 2 64 V 50/60H z NOMINAL SWITCHING AC250V 5A CAPACITY Hangil Control Co., Ltd 2008-09-24... - Page 6 4-2. Drawing - HCR-2216 (Receiver) - HCR-2216 (Receiver) - HCT-2216 (Transmitter) - HCT-2216 (Transmitter) À ü ¿ ø À ü Á ö HCT-2216 Á Ö ½ Ä Ç Ñ ± æ Á ¦ ¾ î È ¸ » ç P lease use the p roduc t a fte r read i ng the m anua l ca re fu lly .
-
Page 7: Installation And Setup
Found While Using the Transmitte r and the Receiver, Stop its Use and Call to your Local Dealer or Our Factory Stop its Use , and Call to your Local Dealer or Our Factory . Hangil Control Co., Ltd 2008-09-24... - Page 8 Open the case of the tr ansmitter and the receiver; see the Address Code Switch is adj u sted the same position. ADDRESS Eg. Refer to the settin gs of the Channel Switch and fre quenc y as below. ADDRESS Hangil Control Co., Ltd 2008-09-24...
-
Page 9: Operating Process
S f t - See what the Crane and the Transmitter Move the Same Direction - Never to Operate Out of Sight. (Be Sure to Operate in Sight of the Crane and the Freight.) Hangil Control Co., Ltd 2008-09-24... -
Page 10: Operating Flowchart
7. OPERATING FLOWCHART 7. OPERATING FLOWCHART... -
Page 11: Maintenance
6. J o int state of the IC terminal pins. 7. Contact state of antenna 8. Operation state of each operation lamp. 9. The fix i ng state of all fix e d dip switches. Hangil Control Co., Ltd 2008-09-24... -
Page 12: Troubleshooting Guide
Replace the RF Module EX A MINATION WITH THE NAK E D CHECK THE BROK E N PARTS BY A SHOC K AND MAINTENANCE OTHERS NO CAUSES FOUND REQ U EST WARRANTY SERV I CE Hangil Control Co., Ltd 2008-09-24... -
Page 13: Charger And Battery
6. If the batteries life time shorter than usual, push the disch arge switch to discharge. 7. Look out the foreign material to the connection part. 8. Take careful the foreign material is at the bolt make them h ard to move. Hangil Control Co., Ltd 2008-09-24...
Need help?
Do you have a question about the HCT-2216 and is the answer not in the manual?
Questions and answers