Advertisement
Operation Guide 4362
Analog Timekeeping
The analog time of this watch is synchronized with the digital time. The analog time
setting is adjusted automatically whenever you change the digital time.
Note
• The hands for the analog timepiece move to adjust to a new setting whenever any of
the following occurs.
When you change the digital time setting
When you change the Home City code and/or DST setting
• If the analog time does not match the digital time for any reason, use the procedure
described under "To adjust the analog time" to match the analog setting to the digital
setting.
• Whenever you need to adjust both the digital and the analog time settings manually,
make sure you adjust the digital setting first.
• Depending on how much the hands have to move in order to adjust to the digital
time, it may take some time before they stop moving.
To adjust the analog time
1. In the Timekeeping Mode, press C five times to enter
the Hand Setting Mode.
2. Hold down A until the current digital time starts to
flash, which indicates the setting screen.
3. Use D and B to adjust the analog setting as
described below.
When you want to do this:
• Press D.
Move the hand setting
forward 20 seconds
• Hold down D.
Move the hand setting a short
• Release D when the hands reach the setting
way forward at high speed
you want.
• While holding down D to move the hands at
Move the hand setting a
high speed, press B to lock the high-speed
long way forward at high
speed
hand movement.
• To stop the hand movement, press any
button.
• Hand movement stops automatically if the hour
hand makes one full (12-hour) revolution.
4. Press A to exit the setting screen.
• The minute hand will be adjusted slightly to match the seconds when you exit the
setting screen.
• To return to the Timekeeping Mode, press C.
World Time
The World Time Mode digitally displays the current time in
City code
48 cities (29 time zones) around the world.
• If the current time shown for a city is wrong, check your
Home City time settings and make the necessary
changes.
• All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
Current time in
selected city
To view the time in another city
While in the World Time Mode, press D to scroll through the city codes (time zones)
to the east.
• For full information on city codes, see the "City Code Table".
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use D to display the city code
(time zone) whose Standard Time/Daylight Saving Time
setting you want to change.
2. Hold down A to toggle Daylight Saving Time (DST
indicator displayed) and Standard Time (DST indicator
not displayed).
• Note that you cannot use the World Time Mode to
change the DST setting of the Home City code you
currently have selected in the Timekeeping Mode. See
"To set the digital time and date" for information about
turning the Home City code DST setting on and off.
DST indicator
• The DST indicator will appear on the display whenever
you display a city code for which Daylight Saving Time is
turned on.
• Note that the DST/Standard Time setting affects only the
currently displayed city code. Other city codes are not
affected.
Countdown Timer
You can set the countdown timer within a range of one to
60 minutes. An alarm sounds when the countdown
reaches zero.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C.
Minutes
Seconds
1/10 second
To set the countdown start time
1. While the countdown start time is on the display in the Countdown Timer Mode,
hold down A until the current countdown start time starts to flash, which indicates
the setting screen.
• If the countdown start time is not displayed, use the procedure under "To use the
countdown timer" to display it.
2. While a setting is flashing, use D (+) and B (–) to change it.
3. Press A to exit the setting screen.
Perform this button operation:
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached, the alarm sounds for 10 seconds or until
you stop it by pressing any button. The countdown time is automatically reset to its
starting value after the alarm stops.
• Press D while a countdown operation is in progress to pause it. Press D again to
resume the countdown.
• To completely stop a countdown operation, first pause it (by pressing D), and then
press A. This returns the countdown time to its starting value.
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 59 minutes, 59.99
seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• The stopwatch measurement operation continues even
Minutes
if you exit the Stopwatch Mode.
Seconds
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
1/100 second
To measure times with the stopwatch
Elapsed Time
D
➤
D
➤
D
Start
Stop
Re-start
Split Time
D
➤
A
➤
A
Start
Split
Split release
(
displayed)
Two Finishes
D
➤
A
➤
D
Start
Split
Stop
First runner
Second runner
finishes.
finishes.
Display time of
first runner.
Alarm
When the alarm is turned on, the alarm sounds when the
Alarm on indicator
alarm time is reached. You can also turn on an Hourly
PM indicator
Time Signal, which will cause the watch to beep twice
every hour on the hour.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
Hourly time signal
on indicator
Alarm time
(Hour : Minutes)
To set the alarm time
1. In the Alarm Mode, hold down A until the hour setting of the alarm time starts to
flash, which indicates the setting screen.
• This operation automatically turns on the alarm.
2. Press C to move the flashing between the hour and minute settings.
3. While a setting is flashing, use D (+) and B (–) to change it.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (PM indicator).
4. Press A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds, regardless of the mode the
watch is in.
• To stop the alarm tone after it starts to sound, press any button.
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To turn the Daily alarm and the Hourly Time Signal on and off
In the Alarm Mode, press D to cycle through the settings shown below.
Alarm On Indicator / Hourly Time Signal On Indicator
Alarm Off
Alarm On
Signal Off
Signal Off
• The alarm on indicator and the Hourly Time Signal on indicator are shown on the
display in all modes while these functions are turned on.
➤
D
➤
A
Stop
Clear
➤
D
➤
A
Stop
Clear
A
➤
A
➤
Split release
Clear
Display time of
second runner.
Alarm Off
Alarm On
Signal On
Signal On
2
Advertisement
