Advertisement
WWW.CONCESSIONSTANDS.COM
4-SLOT STANDARD TOASTERS - CTW-4M & CTS-4
120 volts / 208 volts / 220 volts models available; single phase
6-SLOT STANDARD TOASTERS - CTW-6
208/220 volts models available; single phase
2-SLOT STANDARD TOASTERS - CTB-2 & CTW-2
120 volts / 1250 watts / 10.5 amps / single phase
Slot dimensions: W:1”, H:5”, L:5”
l
Fits bread and standard size bagels
1 or 2 slot selector switch
l
Timer knob (turns unit on)
l
Ejector knob
l
Pull-out crumb tray
l
2-SLOT BAGEL TOASTERS - CBT-2 & CBT-2B
120 volts / 1200 watts / 10 amps / single phase
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
Slot dimensions: W:1”, H:5”, L:5”
l
Fits bread and standard size bagels
2 or 4 slot selector switch
l
Timer knob (turns unit on)
l
Pull-out crumb tray
l
Ejector knob
l
Slot dimensions: W:1”, H:5”, L:5”
l
Fits bread and standard size bagels
2, 4 or 6 slot selector switch
l
Timer knob (turns unit on)
l
Pull-out crumb tray
l
Ejector knob
l
Slot dimensions: W:1.25”, H:5”, L:5”
l
Fits bread and larger size bagels
Timer knob (turns unit on)
l
Pull-out crumb tray
l
Ejector knob
l
NOTE: This model does not have a selector
l
switch; both slots heat when unit is turned on
4
GENERAL OPERATING INSTRUCTIONS
ALL MODELS EXCEPT CBF-4M BUFFET TOASTER
(note, if you have the discontinued Models:
CTB-4E, CTS-4E, or CSTW-2, see separate manuals)
1) Prior to the initial use or after the toaster has not been used for a period
of time (60-90 minutes), it is important to PREHEAT your toaster. This
avoids uneven toasting and will provide more efficient toasting throughout
the day. To preheat, press the slot selector switch to the maximum
number of slots, and turn the timer dial to the desired setting. Preheat
for at least 1 - 2 minutes.
2) After preheating, lift up the Ejector Knob and place bread in proper slots.
Select proper setting of selector switch for the number of slices being toasted,
(see 3) below) and turn the timer dial to the desired shade.
IMPORTANT: By turning the timer dial on, your toasting cycle will begin
immediately. Once the toasting has begun you should notice the neon light
will illuminate. Please note that the higher the timer number, the darker the
toast will be.
3) Selector switch settings vary by model:
4-Slot Standard Toasters:
l
-Selector I I should be pressed when toasting 1 or 2 slices of product. Make
sure to use the far left toaster slots.
-Selector I I I I should be pressed when toasting 3 or 4 slices.
6-Slot Standard Toasters:
l
-Selector I I should be pressed when toasting 1 or 2 slices of product. Make
sure to use the far left toaster slots.
-Selector I I I I should be pressed when toasting 3 or 4 slices. Make sure
to use the 3 or 4 left toaster slots.
-Selector I I I I I I should be pressed when toasting 5 or 6 slices of product.
2-Slot Standard Toasters:
l
-Selector I should be pressed when toasting 1 slice of product. Make sure
to use the far left toaster slot.
-Selector Il should be pressed when toasting 2 slices of product.
2-Slot Bagel Toasters:
l
This model does not have a selector switch. Turning on the toaster
with the timer knob will heat both slots.
4) When the timer reaches zero and when the ticking stops, the toasting cycle
is complete. The neon light will also switch off. You may interrupt the toasting
to check the progress at any time during the cycle by lowering the ejector
knob. This will raise the toast in the slot to check the product for doneness
without shutting the toaster off. (This will not change or “reset” the toasting
time as set by the timer.) After checking progress, raise the ejector knob to
lower the toast in the slot to complete the toasting cycle.
5) To eject the toast or bagel, simply press lightly down on the ejector knob. The
toast will remain in the slots until you do this (a keep warm feature appreciated
in the commercial industry.)
5
Advertisement
